![Makita LXT DCS551RMJ [5/80] For battery cartridge](/img/pdf.png)
Makita LXT DCS551RMJ [5/80] For battery cartridge
![Makita LXT DCS551RMJ [5/80] For battery cartridge](/views2/1888812/page5/bg5.png)
5
sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
17. Check the operation and condition of the
lower guard spring. If the guard and the
spring are not operating properly, they must
be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a buildup of debris.
18.
Lower guard may be retracted manually only for
special cuts such as "plunge cuts" and "compound
cuts". Raise lower guard by retracting handle and
as soon as blade enters the material, the lower
guard must be released.
For all other sawing, the
lower guard should operate automatically.
19.
Always observe that the lower guard is covering
the blade before placing tool down on bench or
floor.
An unprotected, coasting blade will cause the
tool to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
20. To check lower guard, open lower guard by
hand, then release and watch guard closure.
Also check to see that retracting handle does
not touch tool housing. Leaving blade exposed
is VERY DANGEROUS and can lead to serious
personal injury.
Additional safety warnings
21. Do not stop the blades by lateral pressure on
the blade.
22. DANGER:
Do not attempt to remove cut material when
blade is moving.
CAUTION: Blades coast after turn off.
23.
Place the wider portion of the tool base on that part
of the workpiece which is solidly supported, not on
the section that will fall off when the cut is made.
24. Never attempt to make a cut with the tool held
upside down in a vise. This is extremely
dangerous and can lead to serious accidents.
25. Wear safety goggles and hearing protection
during operation.
26. Do not use any abrasive wheels.
27. Only use the blade with the diameter that is
marked on the tool or specified in the manual.
Use of an incorrectly sized blade may affect the
proper guarding of the blade or guard operation
which could result in serious personal injury.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
ENC007-9
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50
ﾟ C (122 ﾟ F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. Follow your local regulations relating to
disposal of battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
2. Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10
ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
Содержание
- Dcs551 1
- Ec declaration of conformity 3
- Explanation of general view 3
- Specifications 3
- Cordless metal cutter safety warnings 4
- General power tool safety warnings 4
- Save all warnings and instructions for future reference 4
- For battery cartridge 5
- Important safety instructions 5
- Save these instructions 5
- Tips for maintaining maximum battery life 5
- Warning 5
- Functional description 6
- Indicating remaining battery capacity 6
- Indicating the remaining battery capacity 6
- Installing or removing battery cartridge 6
- Switch action 6
- Adjusting depth of cut 7
- Automatic speed change function 7
- Lighting the lamp 7
- Sighting 7
- Tool battery protection system 7
- Assembly 8
- Hex wrench storage 8
- Installing or removing hook 8
- Operation 8
- Removing or installing blade 8
- Rip fence guide rule optional accessory 8
- Inspecting blade 9
- Maintenance 9
- Optional accessories 9
- Es izjava o skladnosti 10
- Razlaga splošnega pogleda 10
- Tehnični podatki 10
- Shranite vsa opozorila in navodila za kasnejšo uporabo 11
- Splošna varnostna opozorila za električno orodje 11
- Varnostna opozorila za brezžični rezalnik kovin 11
- Nasveti za maksimalno življenjsko dobo akumulatorja 12
- Opozorilo 12
- Pomembna varnostna navodila 12
- Shranite ta navodila 12
- Za baterijske vložke 12
- Delovanje stikala 13
- Nameščanje ali odstranjevanje akumulatorske baterije 13
- Opis delovanja 13
- Prikaz preostale zmogljivosti akumulatorja 13
- Prikazuje preostalo zmogljivost akumulatorja 13
- Funkcija samodejne spremembe hitrosti 14
- Nastavljanje globine rezanja 14
- Poravnanje na rezalno linijo 14
- Prižiganje lučke 14
- Zaščitni sistem orodja akumulatorja 14
- Delovanje 15
- Montaža 15
- Namestitev ali odstranitev kavlja 15
- Odstranjevanje ali nameščanje rezila 15
- Shranjevanje inbus ključa 15
- Dodatni pribor 16
- Pregled rezila 16
- Vzdrževanje 16
- Vzporedni prislon vodilno ravnilo dodatni pribor 16
- Deklarata e konformitetit me ke në 17
- Shpjegim i pamjes së përgjithshme 17
- Specifikimet 17
- Paralajmërimet e përgjithshme për sigurinë e veglës 18
- Paralajmërimet për sigurinë e prerësit të metalit me bateri 18
- Ruajini të gjitha paralajmërimet dhe udhëzimet për të ardhmen 18
- Paralajmërim 19
- Për kutinë e baterisë 19
- Ruajini këto udhëzime 19
- Udhëzime të rëndësishme për sigurinë 19
- Instalimi ose heqja e kutisë së baterisë 20
- Këshilla për të ruajtur jetëgjatësinë maksimale të baterisë 20
- Përshkrimi i punës 20
- Ruajini këto udhëzime 20
- Treguesi i kapacitetit të mbetur të baterive 20
- Funksioni i ndryshimit automatik të shpejtësisë 21
- Sistemi i mbrojtjes së veglës baterisë 21
- Treguesi i kapacitetit të mbetur të baterisë 21
- Veprimi i ndërrimit 21
- Heqja ose instalimi i diskut 22
- Instalimi ose heqja e grepit 22
- Montimi 22
- Ndezja e llambës 22
- Rregullimi i thellësisë së prerjes 22
- Ruajtja e çelësit hekzagonal 22
- Shikimi 22
- Inspektimi i diskut 23
- Kufizuesi vizorja udhëzuese aksesor opsional 23
- Mirëmbajtja 23
- Përdorimi 23
- Aksesorë opsionalë 24
- Ez izjava o sukladnosti 33
- Objašnjenje općeg pogleda 33
- Specifikacije 33
- Opća sigurnosna upozorenja za električne ručne alate 34
- Sačuvajte sva upozorenja i upute radi kasnijeg korištenja 34
- Sigurnosna upozorenja za bežični rezač metala 34
- Savjeti za održavanje najduljeg vijeka trajanja baterije 35
- Upozorenje 35
- Važne sigurnosne upute 35
- Za bateriju 35
- Čuvajte ove upute 35
- Funkcionalni opis 36
- Instalacija ili uklanjanje baterije 36
- Prikaz preostalog kapaciteta baterije 36
- Uključivanje i isključivanje 36
- Funkcija za automatsku promjenu brzine 37
- Kada se alat koristi na način pri kojemu troši neobično mnogo struje alat se automatski zaustavlja bez prethodne najave u tom slučaju isključite alat i zaustavite primjenu koja je izazvala preopterećenje alata zatim uređaj ponovno uključite da biste ga pokrenuli 37
- Montaža 37
- Podešavanje dubine rezanja 37
- Sustav zaštite alata baterije 37
- Točno rezanje 37
- Uklanjanje ili postavljanje lista 37
- Uključivanje svjetla 37
- Održavanje 38
- Paralelni graničnik ravnalo za vođenje dodatni pribor 38
- Postavljanje ili uklanjanje kuke 38
- Rad sa strojem 38
- Čuvanje imbus ključa 38
- Dodatni pribor 39
- Pregled lista 39
- Declaraijie de conformitate ce 48
- Explicitarea vederii de ansamblu 48
- Specificaıii 48
- Avertismente generale de siguranijĕ pentru unelte electrice 49
- Avertismente privind siguranıa pentru maşina de tĕiat metal cu acumulator 49
- Pĕstraiji toate avertismentele şi instrucijiunile pentru consultĕri ulterioare 49
- Avertisment 50
- Instrucıiuni importante privind siguranıa 50
- Pentru cartuşul acumulatorului 50
- Pĕstraıi aceste instrucıiuni 50
- Descriere funcıionalĕ 51
- Indicarea capacitĕijii rĕmase a acumulatorului 51
- Instalarea sau scoaterea cartuşului acumulatorului 51
- Pĕstraıi aceste instrucıiuni 51
- Sfaturi pentru obijinerea unei durate maxime de exploatare a acumulatorului 51
- Acijionarea întrerupĕtorului 52
- Funcijie de schimbare automatĕ a turaijiei 52
- Indicarea capacitĕijii rĕmase a acumulatorului 52
- Sistem de protecijie maşinĕ acumulator 52
- Aprinderea lĕmpii 53
- Demontarea sau montarea pânzei 53
- Depozitarea cheii inbus 53
- Montare 53
- Montarea sau demontarea agĕijĕtorii 53
- Reglarea adâncimii de aşchiere 53
- Vizarea 53
- Funcıionare 54
- Inspectarea pânzei 54
- Riglĕ de ghidare regulĕ de ghidare accesoriu opijional 54
- Întreıinere 54
- Accesorii opıionale 55
- 78 db a k 3 db a 80 db a 56
- En60745 56
- Makita dcs551 2006 42 en60745 56
- Makita 80
- Makita corporation 80
Похожие устройства
- Makita LXT DCS551Z Инструкция к товару
- Makita LXT DCS553Z Инструкция по эксплуатации
- Парма 235Д 02.004.00004 Инструкция к товару
- Зубр с 10 битами ОШ-7.2 Н Инструкция к товару
- Зубр с 10 битами ОШ-7.2 Н Приложение к инструкции
- Pulsar ПД 210-1900 793-435 инструкция
- Ресанта ДП-20/190А 75/11/5 Паспорт
- Worx WX255 SD Slide Driver WX255 Инструкция к товару
- Ryobi EWS1150RS2 5133000825 Инструкция по эксплуатации
- Ryobi EWS1150RS 5133000552 Инструкция по эксплуатации
- Ryobi ONE+ R18CS-0 5133002338 Таблица времени работы инструментов ONE+ с аккумуляторами разной емкости
- Ryobi ONE+ R18CS-0 5133002338 Инструкция по эксплуатации
- Ryobi ONE+ R18CSP-0 5133002628 Таблица времени работы инструментов ONE+ с аккумуляторами разной емкости
- Ryobi ONE+ R18CSP-0 5133002628 Инструкция к товару
- Ryobi ONE+ RWSL1801M 5133001164 Таблица времени работы инструментов ONE+ с аккумуляторами разной емкости
- Ryobi ONE+ RWSL1801M 5133001164 Инструкция по эксплуатации
- Ryobi RCS1400-G 5133002778 Инструкция по эксплуатации
- Ryobi RCS1600-K 5133002779 Инструкция по эксплуатации
- Stalex QCS-400 388040 Инструкция к товару
- STATUS CP190C 4071101 Инструкция по эксплуатации