Festool Precisio CS 70 EB 561136 [15/118] Caution

Festool Precisio CS 70 EB 561136 [15/118] Caution
15
PRECISIO -
GB
Never process material containing asbestos. -
Do not remove offcuts or other workpiece parts -
from the cutting area while the tool is still run-
ning and until the saw blade stops.
If the saw blade is blocked, switch the machine -
off immediately and disconnect the mains
plug. Do not remove the jammed workpiece
until you have done this.
5.2 Emission levels
Noise emissions have been measured in accord-
ance with the specifi cations in EN 61029. These
specifi cations apply for operation as a trimming
saw and bench-mounted circular saw.
Noise level
Sound power level, idling 91 dB(A)
Sound power level,
during operation 103 dB(A)
Measuring uncertainty allowance K = 3 dB
Workplace emission levels
Workplace emission, idling 77 dB(A)
Workplace emission,
during operation 90 dB(A)
CAUTION
The noise produced during work may damage
your hearing.
Wear ear protection!
Measured acceleration < 2.5 m/s²
The emission values specifi ed (vibration, noise)
were measured in accordance with the test con-
ditions stipulated in EN 61029 and are intended
for machine comparisons. They are also used for
making preliminary estimates regarding vibra-
tion and noise loads during operation.
The emission values specifi ed refer to the main
applications for which the power tool is used. If
the electric power tool is used for other applica-
tions, with other tools or is not maintained suffi -
ciently prior to operation, however, the vibration
and noise load may be higher when the tool is
used. Take into account any machine idling times
and downtimes to estimate these values more
accurately for a specifi ed time period. This may
signifi cantly reduce the load during the machine
operating period.
5.3 Other risks
In spite of compliance with all relevant design
regulations, dangers may still present them-
selves when the machine is operated, e.g.:
Saw blades made of High Speed Steel (HSS -
steel) must not be used.
Transport and store the tools in a suitable re- -
ceptacle;
Wear suitable personal protective equipment: -
ear protection to reduce the risk of hearing
loss, safety goggles, a dust mask to prevent
inhalation of harmful dust, protective gloves
when working with raw materials and when
changing tools.
Only use tools that meet standard EN 847-1. -
Pull the plug from the main power socket be- -
fore changing tools and rectifying faults such
as removing trapped splinters.
When cutting wood, connect the machine to a -
dust extractor corresponding to EN 60335-2-
69, dust category M.
To minimise noise, the tool must be sharpened -
and all noise reducing elements (covers etc.)
must be properly adjusted.
Only use the machine if all safety devices are in -
their correct positions, the machine is in good
condition and has been well maintained.
Faults on the machine, including the separat- -
ing guards or the tool, must be reported to
maintenance staff immediately upon discov-
ery. The machine must not be used until the
fault has been eliminated.
Cutting rebates or grooves is only permitted -
with a suitable protective device fi tted, e.g. a
protective tunnel over the saw table.
Do not use circular saws for cutting slots -
(grooves in workpiece).
Do not use the top protective cover as a handle -
for transportation!
Before transporting the machine, make sure -
that the top protective guard covers the top
section of the saw blade.
Use a suitable device to support long work- -
pieces and ensure that they are horizontal.
Make sure that there is adequate lighting in -
the room or workplace.
Operating personnel must have received ade- -
quate training in the use, set-up and operation
of the machine.
Always assume the correct position before -
starting work:
- front at the operating end,
- facing the machine,
- next to the cutting line.

Содержание

Скачать