Home
Главная
Skil Masters
Полировочная Машина
9955 NA
Инструкция по эксплуатации Страница: 6

Skil Masters 9955 NA Инструкция по эксплуатации онлайн [6/144] 161168

a) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating accessory.

The accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in the direction opposite to the wheel’s movement

at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

GENERAL

• Only use this tool for dry polishing

• Only use the anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

• Do not use damaged, deformed or vibrating accessories

OUTDOOR USE

• When used outdoors, connect the tool via a fault current

(FI) circuit breaker with a triggering current of 30 mA

maximum, and only use an extension cord which is

intended for outdoor use and equipped with a

splashproof coupling-socket

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Always mount auxiliary handle A 3 or B 3; never use the

tool without it

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• When working, always hold the tool rmly with both

hands and take a secure stance

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• In case of current interruption or when the plug is

accidentally pulled out, release switch H 3 in order to

prevent uncontrolled restarting

AFTER USE

• Before you put down the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of auxiliary handles 5

! disconnect the plug

- screw auxiliary handle A on the right or the left of the

tool (depending on the work to be carried out)

- mount auxiliary handle B as illustrated and tighten

both screws supplied with hex key C

• Mounting of accessories 3

! disconnect the plug

- clean spindle D and all parts to be mounted

- screw VELCRO backing pad E onto spindle D while

pushing spindle-lock button F

! push spindle-lock button F only when spindle D is

at a standstill

- simply press wool bonnet G onto VELCRO backing

pad E

- for removing accessories handle vice-versa

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

Содержание

Похожие устройства

a Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces Always use auxiliary handle If provided for maximum control over kickback or torque reaction during start up The operator can control torque reactions or kickback forces if proper precautions are taken b Never place your hand near the rotating accessory The accessory may kickback over your hand c Do not position your body in the area where power tool will move If kickback occurs Kickback will propel the tool in the direction opposite to the wheel s movement at the point of snagging d Use special care when working corners sharp edges etc Avoid bouncing and snagging the accessory Comers sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback e Do not attach a saw chain woodcarving blade or toothed saw blade Such blades create frequent kickback and loss of control Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning wear a dust mask and work with a dust extraction device when connectable Follow the dust related national requirements for the materials you want to work with Secure the workpiece a workpiece clamped with clamping devicesorin a vice is held more securely than by hand Do not clamp the tool in a vice Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps DURING USE When working always hold the tool firmly with both hands and take a secure stance Always keep the cord away from moving parts of the tool direct the cord to the rear away from the tool If the cord is damaged or cut through while working do not touch the cord but immediately disconnect the plug Never use the tool when cord is damaged have it replaced by a qualified person In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug In case of current interruption or when the plug is accidentally pulled out release switch H in order to prevent uncontrolled restarting AFTER USE Before you put down the tool switch off the motor and ensure that all moving parts have come to a complete standstill After switching off the tool never stop the rotation of the accessory by a lateral force applied against it WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended GENERAL Only use this tool for dry polishing Only use the flanges which are supplied with this tool This tool should not be used by people under the age of 16 years Always disconnect plug from power source before making any adjustment or changing any accessory Do not work materials containing asbestos asbestos is considered carcinogenic ACCESSORIES SKIL can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer For mounting using non SKIL accessories observe the instructions of the manufacturer concerned Use only accessories with an allowable speed matching at least the highest no load speed of the tool Never use accessories with a blind threaded hole smaller than M14 x 21 mm Do not use damaged deformed or vibrating accessories OUTDOOR USE When used outdoors connect the tool via a fault current Fl circuit breaker with a triggering current of 30 mA maximum and only use an extension cord which is intended for outdoor use and equipped with a splashproof coupling socket BEFORE USE Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply Always mount auxiliary handle A or B never use the tool without it Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhalation of the dust may cause allergic reactions and or respiratory diseases to the operator or bystanders wear a dust mask and work with a dust extraction device when connectable USE Mounting of auxiliary handles I disconnect the plug screw auxiliary handle A on the right or the left of the tool depending on the work to be carried out mount auxiliary handle B as illustrated and tighten both screws supplied with hex key C Mounting of accessories I disconnect the plug clean spindle D and all parts to be mounted screw VELCRO backing pad E onto spindle D while pushing spindle lock button F I push spindle lock button F only when spindle Dis at a standstill simply press wool bonnet G onto VELCRO backing padE for removi ng accessories handl e vi ce versa Before using the tool ensure that accessory is correctly mounted and firmly tightened check if accessory runs freely by turning it by hand 6

Скачать