Skil Masters 9955 NA [7/144] Declaration of conformity c
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil Masters 9955 NA [7/144] Declaration of conformity c

Skil Masters 9955 NA [7/144] Declaration of conformity c
7
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
• On/o
- switch on/o the tool by pulling/releasing trigger H 3
• Electronic soft-start
Ensures reaching the maximum speed smoothly without
a sudden impact when tool is switched on
• Switch locking for continuous use
- pull trigger H
- press knob J with your thumb
- unlock the switch by pulling again trigger H and then
releasing it
• Speed control 6
- with wheel K the maximum speed can be adjusted
from low to high (1-MAX)
- start with wheel K in position 1 (lower speed)
- if needed, select a higher speed while the tool runs
- the optimal working speed depends on the material
and can be determined with practical trials
• Operating the tool
- switch on the tool
- place the tool fully on the surface to be polished and
move it evenly by sections
- one move should overlap the previous move by one
half
- do not stop at a single spot to avoid burning the
coating
- do not move the tool in circles to avoid staining or
burning the coating
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
• Holding and guiding the tool 7
! while working, always hold the tool at the
grey-coloured grip area(s)
- always hold the tool rmly with both hands, so you will
have full control of the tool at all times
- provide for a secure stance
! do not apply so much pressure on the tool that it
comes to a standstill
- keep ventilation slots L 3 uncovered
MAINTENANCE / SERVICE
• Protect the tool from impact, shock and grease
• Always keep tool and cord clean (especially ventilation
slots L 3)
! disconnect the plug before cleaning
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that the product
described under “Technical data” is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
¹ÊÁÂÆιÆ¼½ÊÇǾ¼½Æ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
Ĺ¾ÁÂÿʹ¹¾
ÈÈÊÇιÄ¹Æ¹¿½Ê
27.01.2014
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 86 dB(A) and the sound
power level 97 dB(A) (standard deviation: 3 dB), and the
vibration 8.5 m/s² (hand-arm method; uncertainty K = 1.5
m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns

Содержание

Похожие устройства

ENVIRONMENT test run tool for at least 30 seconds at highest no load speed in a safe position stop immediately in case of considerable vibration or other defects and check tool to determine the cause On off switch on off the tool by pulling releasing trigger H Electronic soft start Ensures reaching the maximum speed smoothly without a sudden impact when tool is switched on Switch locking for continuous use pull trigger H press knob J with your thumb unlock the switch by pulling again trigger H and then releasing it Speed control with wheel K the maximum speed can be adjusted from low to high 1 MAX start with wheel K in position 1 lower speed if needed sei ect a hi gher speed whi Ie the tool runs the optimal working speed depends on the material and can be determined with practical trials Operating the tool switch on the tool place the tool fully on the surface to be polished and move it evenly by sections one move should overlap the previous move by one half do not stop at a single spot to avoid burning the coating do not move the tool in circles to avoid staining or burning the coating before switching off the tool you should lift It from the workpiece the accessory continues to rotate for a short time after the tool has been switched off Holding and guiding the tool I while working always hold the tool at the grey coloured grip area s always hold the tool firmly with both hands so you will have full control of the tool atari times provide for a secure stance I do not apply so much pressure on the tool that It comes to a standstill keep ventilation slots L uncovered Do not dispose of electric tools accessories and packaging together with household waste material only for EU countries in observance of European Directive 2012 19 EC on waste of electric and electronic equipment and its implementation in accordance with national law electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility symbol will remind you of this when the need for disposing occurs DECLARATION OF CONFORMITY C We declare under our sole responsibility that the product described under Technical data is in conformity with the following standards or standardization documents EN 60745 EN 61000 EN 55014 in accordance with the provisions of the directives 2004 108 EC 2006 42 EC 2011 65 EU Technical file at SKIL Europe BV PT SEU ENG1 4825 BD Breda NL Marijn van der Hoofden Operations Engineering Olaf Dijkgraaf Approval Manager SKIL Europe BV 4825 BD Breda NL 27 01 2014 NOISE VIBRATION Measured in accordance with EN 60745 the sound pressure level of this tool is 86 dB A and the sound power level 97 dB A standard deviation 3dB and the vibration 8 5 m s2 hand arm method uncertainty K 1 5 m s2 The vibration emission level has been measured in accordance with a standardised test given in EN 60745 it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned using the tool for different applications or with different or poorly maintained accessories may significantly increase the exposure level the times when the tool is switched off or when it is running but not actually doing the job may significantly reduce the exposure level I protect yourself against the effects of vibration by maintaining the tool and Its accessories keeping your hands warm and organizing your work patterns MAINTENANCE SERVICE Protect the tool from impact shock and grease Always keep tool and cord clean especially ventilation slots L I disconnect the plug before cleaning I do not attempt to clean ventilation slots by inserting pointed objects through openings If the tool should fail despite the care taken in manufacturing and testing procedures repair should be carried out by an after sales service centre for SKIL power tools send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station addresses as well as the service diagram of the tool are listed on www skilmasters com 7

Скачать