Home
Главная
Makita
Шуруповерты И Винтоверты
6802 BV
Инструкция по эксплуатации Страница: 5

Makita 6802 BV [5/20] Additional safety rules

20. Check damaged parts

Before further use of the tool, a guard or other

part that is damaged should be carefully checked

to determine that it will operate properly and per-

form its intended function. Check for alignment of

moving parts, binding of moving parts, breakage

of parts, mounting, and any other conditions that

may affect its operation. A guard or other part

that is damaged should be properly repaired or

replaced by an authorized service center unless

otherwise indicated elsewhere in this instruction

manual. Have defective switches replaced by

and authorized service center. Do not use tool if

switch does not turn it on and off.

21. Warning

The use of any other accessory or attachment

other than recommended in this operating

instruction or the catalog may present a risk of

personal injury.

22. Have your tool repaired by an expert

This electric appliance is in accordance with the

relevant safety rules. Repairing of electric appli-

ances may be carried out only by experts other-

wise it may cause considerable danger for the

user.

ADDITIONAL SAFETY RULES

1. Always be sure you have a firm footing. Be

sure no one is below when using the tool in

high locations.

2. Hold the tool firmly.

3. Keep hands away from rotating parts.

4. When driving into walls, floors or wherever

“live” electrical wires may be encountered,

DO NOT TOUCH ANY METAL PARTS OF THE

TOOLtool! Hold the tool by the insulated

grasping surfaces to prevent electric shock if

you drive into a “live” wire.

5. Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Removing or installing locator assembly

(Fig. 1)

To remove the locator assembly, pull the locking

sleeve forward and then turn it counterclockwise. To

install the locator assembly, screw it clockwise and

then push the locking sleeve back in lightly toward the

motor. Turn the locking sleeve slightly to match the

locking positions and then push in firmly to lock the

locator in place.

Removing or installing magnetic socket bit

(Fig. 2)

Important:

Always be sure that the tool is switched off and

unplugged before removing or installing the bit.

After removing the locator assembly, pull firmly to

remove the magnetic socket bit. To install the bit,

insert it into the tool as far as it will go.

Depth adjustment (Fig. 3 & 4)

Pull the locking sleeve forward and then turn it to

adjust the depth.

Initially, adjust the locator assembly to create a dis-

tance of approximately 0.5 mm from the tip of the

locator to the tip of the socket bit. One full turn of the

locator equals 1.5 mm change in depth. After adjust-

ing the locator assembly, push the locking sleeve in to

lock the locator in place. Drive a trial screw into your

material or a piece of duplicate material. If the depth

is not suitable for the screw, continue adjusting until

the proper depth setting is obtained.

Switch action (Fig. 5)

CAUTION:

Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the trigger. Machine

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. For continuous

operation, pull the trigger and then push in the lock

button. To stop the tool from the locked position, pull

the trigger fully, then release it. A speed control screw

is provided so that maximum tool speed can be lim-

ited (variable). Turn the speed control screw clock-

wise for higher speed, and counterclockwise for lower

speed.

NOTE:

Even with the switch on and motor running, the bit

will not rotate until you fit the point of the bit in the

screw head and apply forward pressure to engage

the clutch.

Reversing switch action (Fig. 6)

CAUTION:

• Always check the direction of rotation before opera-

tion.

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of rota-

tion before the tool stops may damage the tool.

This tool has a reversing switch to change the direc-

tion of rotation. Move the reversing switch lever to the

i position for clockwise rotation or the j position

for counterclockwise rotation.

Makita 6802 BV [5/20] Additional safety rules

Содержание

Похожие устройства