![Makita LS 1440 [10/36] Assembly](/img/pdf.png)
Makita LS 1440 [10/36] Assembly
10
Electric brake
This tool is equipped with an electric blade brake. If the
tool consistently fails to quickly stop blade after switch
trigger release, have tool serviced at a Makita service
center.
The blade brake system is not a substitute for blade
guard. NEVER USE TOOL WITHOUT A FUNCTIONING
BLADE GUARD. SERIOUS PERSONAL INJURY CAN
RESULT.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing saw blade
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
• Use only the Makita socket wrench provided to install
or remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex bolt.
This could cause a personal injury.
To remove the blade, use the socket wrench to loosen
the hex bolt holding the center cover by turning it coun-
terclockwise. Raise the blade guard and center cover.
(Fig. 10)
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt clockwise. Then
remove the hex bolt, outer flange and blade. (Fig. 11 &
12)
To install the blade, mount it carefully onto the spindle,
making sure that the direction of the arrow on the surface
of the blade matches the direction of the arrow on the
blade case. Install the outer flange and hex bolt, and then
use the socket wrench to tighten the hex bolt (left-
handed) securely counterclockwise while pressing the
shaft lock. (Fig. 13 & 14)
CAUTION:
• The inner flange has a 25 mm diameter on one side
and a 25.4 mm diameter on the other. The side with
25.4 mm diameter is marked by “25.4”. Use the correct
side for the hole diameter of the blade you intend to
use. Mounting the blade on the wrong side can result in
dangerous vibration.
Slip the pin on the blade guard into the slot in the guide
arm while returning the blade guard to its original fully
closed position. Then tighten the hex bolt clockwise to
secure the center cover. Lower the handle to make sure
that the blade guard moves properly. Make sure shaft
lock has released spindle before making cut. (Fig. 15)
Dust bag
(Fig. 16)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove par-
ticles adhering to the insides which might hamper further
collection.
NOTE:
• If you connect a Makita vacuum cleaner to your saw,
more efficient and cleaner operations can be per-
formed.
Securing workpiece
Whenever possible, secure the workpiece with the
optional vise. If you must use your hand to hold the work-
piece, then it must be done firmly and securely so as not
to lose control of the workpiece. Your hand and arm must
be kept well away from the blade area (100 mm mini-
mum). Squeeze the workpiece firmly against the guide
fence with your fingers held over the top of the guide
fence. The workpiece must also rest steadily on the turn
base.
WARNING:
• Never use your hand to hold the workpiece that
requires your hand to be any closer than 100 mm from
the blade area. In this case, always use the optional
vise to secure the workpiece. After any cutting opera-
tion, raise the blade gently. Never raise the blade until it
has come to a complete stop. Serious injury may result.
Horizontal vise (optional accessory) (Fig. 17)
The horizontal vise can be installed on either the left or
right side of the base. When performing 30° or greater
miter cuts, install the horizontal vise on the side opposite
the direction in which the turn table is to be turned. By
turning the vise knob counterclockwise, the screw is
released and the vise shaft can be moved rapidly in and
out. By turning the vise knob clockwise, the screw
remains secured. To grip the workpiece, turn the vise
knob gently clockwise until the projection reaches its top-
most position, then fasten securely. If the vise knob is
forced in or pulled out while being turned clockwise, the
projection may stop at an angle. In this case, turn the
vise knob back counterclockwise until the screw is
released, before turning again gently clockwise.
CAUTION:
• Grip the workpiece only when the projection is at the
topmost position. Failure to do so may result in insuffi-
cient securing of the workpiece. This could cause the
workpiece to be thrown, cause damage to the blade or
cause the loss of control, which can result in PER-
SONAL INJURY.
Holders and holder assembly (optional accessories)
(Fig. 18)
The holders and the holder assembly can be installed on
either side as a convenient means of supporting work-
pieces horizontally. Install them as shown in Fig. 18.
Then tighten the screws firmly to secure the holders and
the holder assembly.
When cutting long workpieces, use the holder-rod
assembly (optional accessory). It consists of two holder
assemblies and two rods 12. (Fig. 19)
CAUTION:
• Always support long workpieces level with the top sur-
face of the turn base for accurate cuts and to prevent
dangerous loss of control of the tool.
Содержание
- Ls1440 1
- Symbole 6
- Символы 6
- Don t force small tools or attachments to do the job of a heavy duty tool don t use tools for pur poses not intended for example don t use circu lar saw for cutting tree limbs or logs 7
- English 7
- Explanation of general view 7
- For safe operation 1 keep work area clean cluttered areas and benches invite injuries 2 consider work area environment don t expose power tools to rain don t use power tools in damp or wet locations keep work area well lit don t use power tools in presence of flammable liquids or gases 3 guard against electric shock prevent body contact with grounded surfaces e g pipes radiators ranges refrigerators 4 keep children away do not let visitors contact tool or extension cord all visitors should be kept away from work area 5 store idle tools when not in use tools should be stored in dry high or locked up place out of the reach of chil dren 6 don t force tool it will do the job better and safer at the rate for which it was intended 7
- Safety instructions 7
- Specifications 7
- Warning when using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following read all these instruc tions before attempting to operate this product and save these instructions 7
- Additional safety rules for tool 8
- Dress properly do not wear loose clothing or jewelry they can be caught in moving parts rubber gloves and non skid footwear are recommended when work ing outdoors wear protective hair covering to contain long hair 9 use safety glasses and hearing protection also use face or dust mask if cutting operation is dusty 10 connect dust extraction equipment if devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used 11 don t abuse cord never carry tool by cord or yank it to disconnect it from receptacle keep cord from heat oil and sharp edges 12 secure work use clamps or a vise to hold work it s safer than using your hand and it frees both hands to oper ate tool 13 don t overreach keep proper footing and balance at all times 14 maintain tools with care keep tools sharp and clean for better and safer performance follow instructions for lubricating and changing accessories inspect tool cords periodically and if damaged have 8
- Warning the use of any other accessory or attachment other than recommended in this operating instruction or the catalog may present a risk of personal injury 22 have your tool repaired by an expert 8
- Watch what you are doing use common sense do not operate tool when you are tired 20 check damaged parts before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and per form its intended function check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation a guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual have defective switches replaced by and authorized service center do not use tool if switch does not turn it on and off 8
- Adjusting the miter angle 9
- Bench mounting 9
- Blade guard 9
- Fence plate 9
- Functional description 9
- Installation 9
- Kerf board 9
- Maintaining maximum cutting capacity 9
- Save these instructions 9
- Switch action fig 9 9
- Assembly 10
- Dust bag 10
- Electric brake 10
- Installing or removing saw blade 10
- Securing workpiece 10
- Carrying tool 11
- Maintenance 11
- Operation 11
- After use 12
- Ec declaration of conformity 12
- Makita international europe ltd 12
- Noise and vibration 12
- Replacing carbon brushes 12
- Achtung beim gebrauch von elektrowerkzeugen sind zum schutz gegen elektrischen schlag ver letzungsund brandgefahr folgende grundsätzli chen sicherheitsmaßnahmen zu geachten lesen und beachten sie diese hinweise bevor sie das gerät benutzen 1 halten sie ihren arbeitsbereich in ordnung unordnung im arbeitsbereich ergibt unfallgefahr 2 berücksichtigen sie umgebungseinflüsse setzen sie elektrowerkzeuge nicht dem regen aus benützen sie elektrowerkzeuge nicht in feuchter oder nasser umgebung sorgen sie für gute beleuchtung benützen sie elektrowerk zeuge nicht in nähe von brennbaren flüssigkei ten oder gasen 3 schützen sie sich vor elektrischem schlag vermeiden sie körperberührung mit geerdeten teilen zum beispiel rohren heizkörpern her den kühlschränken 4 halten sie kinder fern lassen sie andere personen nicht das werk zeug oder kabel berühren halten sie sie von ihrem arbeitsbereich fern 5 bewahren sie ihre werkzeuge sicher auf unbenutzte werkzeuge sollten in trockenem verschlossenem raum un 13
- Deutsch 13
- Sicherheitshinweise 13
- Technische daten 13
- Übersicht 13
- Zusätzliche sicherheitsregeln für die maschine 14
- Befestigung der säge auf einer werkbank 15
- Bewahren sie diese hinweise sorgfältig auf 15
- Funktionsbeschreibung 15
- Montage 15
- Schutzhaube abb 3 u 4 15
- Anschlagplatte 16
- Aufrechterhaltung der maximalen schnittleistung abb 6 u 7 16
- Einstellung des gehrungswinkels abb 8 16
- Elektrische bremse 16
- Montage 16
- Montage und demontage des sägeblatts 16
- Schalterfunktion abb 9 16
- Schlitzplatte abb 5 16
- Abb 19 17
- Betrieb 17
- Sicherung von werkstücken 17
- Staubsack abb 16 17
- Einstellen des schnittwinkels 18
- Tragen der maschine 18
- Wartung 18
- Auswechseln der kohlebürsten 19
- Ce 2003 19
- Ce konformitätserklärung 19
- Einstellung für reibungslose griffbewegung 19
- Geräusch und vibrationsentwicklung 19
- Makita international europe ltd 19
- Nach dem gebrauch 19
- Dane techniczne 20
- Instrukcje bezpieczeństwa 20
- Polski 20
- Wyjaśnienia dotyczące urządzenia i jego użycia 20
- Dodatkowe zasady bezpieczeństwa dotyczące narzędzia 21
- Mocowanie do stołu roboczego 22
- Montaż 22
- Nie wyrzucaj instrukcji obsługi 22
- Opis działania 22
- Osłona tarczy rys 3 i 4 22
- Płyta z nacięciem rys 5 22
- Hamulec elektryczny 23
- Montaż 23
- Płyta osłony 23
- Regulacja kąta cięcia w poziomie rys 8 23
- Wyłącznik rys 9 23
- Zachowanie maksymalnej wydajności cięcia rys 6 i 7 23
- Zakładanie lub zdejmowanie tarczy 23
- Mocowanie obrabianych elementów 24
- Rys 17 24
- Składanie 24
- Worek na pył rys 16 24
- Konserwacja 25
- Przenoszenie narzędzia 25
- Regulacja kąta cięcia 25
- Regulacja w celu uzyskania płynnej pracy uchwytu 25
- Ce 2003 26
- Makita international europe ltd 26
- Po zakończeniu pracy 26
- Szumy i drgania 26
- Ue deklaracja zgodności 26
- Wymiana szczotek węglowych 26
- Держитесь подальше от детей 27
- Для безопасного функционирования 1 поддерживайте чистоту на рабочем месте 27
- Инструкции по мерам безопасности 27
- Правильно храните неработающие инструменты 27
- Предостережение при использовании электрических инструментов следует всегда соблюдать основные меры безопасности для уменьшения опасности пожара поражения электрическим током и персональных травм включая следующие 27
- Предохраняйтесь от поражения электрическим током 27
- Прочитайте эти инструкции перед тем как пытаться управлять этим изделием и сохраните эти инструкции 27
- Русский язык 27
- Технические характеристики 27
- Учитывайте рабочую окружающую среду 27
- Будьте бдительны 28
- Дополнительные правила безопасности для инструмента 28
- Закрепите рабочее изделие 28
- Избегайте случайных запусков 28
- Используйте для ремонта услуги специалиста 28
- Используйте защитные очки и предохранительные приборы для слуха 28
- Используйте правильный инструмент 28
- Не заходите слишком далеко 28
- Не прилагайте усилие к шнуру 28
- Одевайтесь правильно 28
- Осторожно обращайтесь с инструментами 28
- Отсоединяйте инструменты 28
- Подсоедините пылевсасывающее оборудование 28
- Предостережение 28
- Проверяйте поврежденные части 28
- Шнуры удлинители для использования на улице 28
- Прикрепление к верстаку 29
- Сохраните эти инструкции 29
- Установка 29
- Функциональное описание 29
- Щиток лезвия рис 3 и 4 29
- Действия при переключении рис 9 30
- Доска с пропилом рис 5 30
- Направляющая пластина 30
- Поддержание максимальной режущей способности рис 6 и 7 30
- Регулировка угла отрезки 30
- Сборка 30
- Установка или удаление лезвия пилы 30
- Электрический тормоз 30
- Мешок для пыли 31
- Фиксация рабочего изделия 31
- Эксплуатация 32
- Замена угольных щеток 33
- Обслуживание 33
- Переноска инструмента 33
- После использования 33
- Регулировка для плавной работы рукоятки 33
- Регулировка угла отрезки 33
- Ce 2003 34
- Makita international europe ltd 34
- Ес декларация соответствия 34
- Шум и вибрация 34
Похожие устройства
- Gorenje IT612AC Инструкция по эксплуатации
- Ariston ABS Pro Eco 65 H Slim Инструкция по эксплуатации
- Samsung GT-S8530 Metallic Black Инструкция по эксплуатации
- Hyundai H-CF402 Инструкция по эксплуатации
- Siemens ER 847501E Инструкция по эксплуатации
- Hyundai H-CSW504 Инструкция по эксплуатации
- Timberk WHEX-6 OC Инструкция по эксплуатации
- Gorenje IT612AXC Инструкция по эксплуатации
- Samsung GT-S5570 Dark Grey Инструкция по эксплуатации
- Makita LS 1040 F Инструкция по эксплуатации
- Siemens ER 657502 Инструкция по эксплуатации
- Makita LS 0714 Инструкция по эксплуатации
- Hyundai H-CSK502 Инструкция по эксплуатации
- Diam CSN-355А 620016 Инструкция по эксплуатации
- Gorenje EC57341AX Инструкция по эксплуатации
- Siemens ER 657501E Инструкция по эксплуатации
- Makita LH 1040 Инструкция по эксплуатации
- Hyundai H-CSW694 Инструкция по эксплуатации
- Husqvarna DS40 Gyro 9651576-05 Инструкция по эксплуатации
- Siemens ER 617501E Инструкция по эксплуатации
Скачать
Случайные обсуждения