Makita LS 1440 [9/36] Functional description
9
26. Connect miter saws to a dust collecting device
when sawing.
27. Select saw blades in relation to the material to
be cut.
28. Take care when slotting.
29. Replace the kerf board when worn.
SAVE THESE INSTRUCTIONS
INSTALLATION
Bench mounting
When the tool is shipped, the handle is locked in the low-
ered position by the handle latch. Release the handle
latch by lowering the handle slightly and turn the handle
latch to the released position. (Fig. 1)
This tool should be bolted with four bolts to a level and
stable surface using the bolt holes provided in the tool’s
base. This will help prevent tipping and possible injury.
(Fig. 2)
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Blade guard
(Fig. 3 & 4)
When lowering the handle, the blade guard rises auto-
matically. The guard is spring loaded so it returns to its
original position when the cut is completed and the han-
dle is raised. NEVER DEFEAT OR REMOVE THE
BLADE GUARD OR THE SPRING WHICH ATTACHES
TO THE GUARD.
In the interest of your personal safety, always maintain
the blade guard in good condition. Any irregular opera-
tion of the blade guard should be corrected immediately.
Check to assure spring loaded return action of guard.
NEVER USE THE TOOL IF THE BLADE GUARD OR
SPRING ARE DAMAGED, FAULTY OR REMOVED.
DOING SO IS HIGHLY DANGEROUS AND CAN CAUSE
SERIOUS PERSONAL INJURY.
If the see-through blade guard becomes dirty, or sawdust
adheres to it in such a way that the blade is no longer
easily visible, unplug the saw and clean the guard care-
fully with a damp cloth. Do not use solvents or any petro-
leum-based cleaners on the plastic guard.
If the blade guard is especially dirty and vision through
the guard is impaired, use the supplied socket wrench to
loosen the hex bolt holding the center cover.
Loosen the hex bolt by turning it counterclockwise and
raise the blade guard and center cover. With the blade
guard so positioned, cleaning can be more completely
and efficiently accomplished. When cleaning is complete,
reverse procedure above and secure bolt. Do not remove
spring holding blade guard. If guard becomes discolored
through age or UV light exposure, contact a Makita ser-
vice center for a new guard. DO NOT DEFEAT OR
REMOVE GUARD.
Kerf board
(Fig. 5)
This tool is provided with the kerf board in the turn base
to minimize tearing on the exit side of a cut. If the kerf
groove has not yet been cut in the kerf board by the fac-
tory, you should cut the groove before actually using the
tool to cut a workpiece. Switch on the tool and lower the
blade gently to cut a groove in the kerf board.
Maintaining maximum cutting capacity
(Fig. 6 & 7)
This tool is factory adjusted to provide the maximum cut-
ting capacity for a 355 mm saw blade.
When installing a new blade, always check the lower limit
position of the blade and if necessary, adjust it as follows:
First, unplug the tool. Lower the handle completely.
Loosen the hex nut at the rear of the gear housing. Use a
screwdriver to turn the adjusting bolt until the periphery
of the blade extends slightly below the top surface of the
turn base at the point where the front face of the guide
fence meets the top surface of the turn base.
With the tool unplugged, rotate the blade by hand while
holding the handle all the way down to be sure that the
blade does not contact any part of the lower base. Re-
adjust slightly, if necessary.
After adjusting, tighten the hex nut with the wrench while
carefully holding the adjusting bolt in position with the
screwdriver.
CAUTION:
• After installing a new blade, always be sure that the
blade does not contact any part of the lower base when
the handle is lowered completely. Always do this with
the tool unplugged.
Adjusting the miter angle
(Fig. 8)
Loosen the grip by turning counterclockwise. Turn the
turn base while pressing down the lock lever. When you
have moved the grip to the position where the pointer
points to the desired angle on the miter scale, securely
tighten the grip clockwise.
CAUTION:
• When turning the turn base, be sure to raise the handle
fully.
• After changing the miter angle, always secure the turn
base by tightening the grip firmly.
Fence plate
The fence plate is designed to prevent smaller cutting
scraps from jamming inside the blade case. The fence
plate moves right or left automatically as the turn base is
rotated.
Switch action (Fig. 9)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Содержание
- Ls1440 1
- Symbole 6
- Символы 6
- Don t force small tools or attachments to do the job of a heavy duty tool don t use tools for pur poses not intended for example don t use circu lar saw for cutting tree limbs or logs 7
- English 7
- Explanation of general view 7
- For safe operation 1 keep work area clean cluttered areas and benches invite injuries 2 consider work area environment don t expose power tools to rain don t use power tools in damp or wet locations keep work area well lit don t use power tools in presence of flammable liquids or gases 3 guard against electric shock prevent body contact with grounded surfaces e g pipes radiators ranges refrigerators 4 keep children away do not let visitors contact tool or extension cord all visitors should be kept away from work area 5 store idle tools when not in use tools should be stored in dry high or locked up place out of the reach of chil dren 6 don t force tool it will do the job better and safer at the rate for which it was intended 7
- Safety instructions 7
- Specifications 7
- Warning when using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following read all these instruc tions before attempting to operate this product and save these instructions 7
- Additional safety rules for tool 8
- Dress properly do not wear loose clothing or jewelry they can be caught in moving parts rubber gloves and non skid footwear are recommended when work ing outdoors wear protective hair covering to contain long hair 9 use safety glasses and hearing protection also use face or dust mask if cutting operation is dusty 10 connect dust extraction equipment if devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used 11 don t abuse cord never carry tool by cord or yank it to disconnect it from receptacle keep cord from heat oil and sharp edges 12 secure work use clamps or a vise to hold work it s safer than using your hand and it frees both hands to oper ate tool 13 don t overreach keep proper footing and balance at all times 14 maintain tools with care keep tools sharp and clean for better and safer performance follow instructions for lubricating and changing accessories inspect tool cords periodically and if damaged have 8
- Warning the use of any other accessory or attachment other than recommended in this operating instruction or the catalog may present a risk of personal injury 22 have your tool repaired by an expert 8
- Watch what you are doing use common sense do not operate tool when you are tired 20 check damaged parts before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and per form its intended function check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation a guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual have defective switches replaced by and authorized service center do not use tool if switch does not turn it on and off 8
- Adjusting the miter angle 9
- Bench mounting 9
- Blade guard 9
- Fence plate 9
- Functional description 9
- Installation 9
- Kerf board 9
- Maintaining maximum cutting capacity 9
- Save these instructions 9
- Switch action fig 9 9
- Assembly 10
- Dust bag 10
- Electric brake 10
- Installing or removing saw blade 10
- Securing workpiece 10
- Carrying tool 11
- Maintenance 11
- Operation 11
- After use 12
- Ec declaration of conformity 12
- Makita international europe ltd 12
- Noise and vibration 12
- Replacing carbon brushes 12
- Achtung beim gebrauch von elektrowerkzeugen sind zum schutz gegen elektrischen schlag ver letzungsund brandgefahr folgende grundsätzli chen sicherheitsmaßnahmen zu geachten lesen und beachten sie diese hinweise bevor sie das gerät benutzen 1 halten sie ihren arbeitsbereich in ordnung unordnung im arbeitsbereich ergibt unfallgefahr 2 berücksichtigen sie umgebungseinflüsse setzen sie elektrowerkzeuge nicht dem regen aus benützen sie elektrowerkzeuge nicht in feuchter oder nasser umgebung sorgen sie für gute beleuchtung benützen sie elektrowerk zeuge nicht in nähe von brennbaren flüssigkei ten oder gasen 3 schützen sie sich vor elektrischem schlag vermeiden sie körperberührung mit geerdeten teilen zum beispiel rohren heizkörpern her den kühlschränken 4 halten sie kinder fern lassen sie andere personen nicht das werk zeug oder kabel berühren halten sie sie von ihrem arbeitsbereich fern 5 bewahren sie ihre werkzeuge sicher auf unbenutzte werkzeuge sollten in trockenem verschlossenem raum un 13
- Deutsch 13
- Sicherheitshinweise 13
- Technische daten 13
- Übersicht 13
- Zusätzliche sicherheitsregeln für die maschine 14
- Befestigung der säge auf einer werkbank 15
- Bewahren sie diese hinweise sorgfältig auf 15
- Funktionsbeschreibung 15
- Montage 15
- Schutzhaube abb 3 u 4 15
- Anschlagplatte 16
- Aufrechterhaltung der maximalen schnittleistung abb 6 u 7 16
- Einstellung des gehrungswinkels abb 8 16
- Elektrische bremse 16
- Montage 16
- Montage und demontage des sägeblatts 16
- Schalterfunktion abb 9 16
- Schlitzplatte abb 5 16
- Abb 19 17
- Betrieb 17
- Sicherung von werkstücken 17
- Staubsack abb 16 17
- Einstellen des schnittwinkels 18
- Tragen der maschine 18
- Wartung 18
- Auswechseln der kohlebürsten 19
- Ce 2003 19
- Ce konformitätserklärung 19
- Einstellung für reibungslose griffbewegung 19
- Geräusch und vibrationsentwicklung 19
- Makita international europe ltd 19
- Nach dem gebrauch 19
- Dane techniczne 20
- Instrukcje bezpieczeństwa 20
- Polski 20
- Wyjaśnienia dotyczące urządzenia i jego użycia 20
- Dodatkowe zasady bezpieczeństwa dotyczące narzędzia 21
- Mocowanie do stołu roboczego 22
- Montaż 22
- Nie wyrzucaj instrukcji obsługi 22
- Opis działania 22
- Osłona tarczy rys 3 i 4 22
- Płyta z nacięciem rys 5 22
- Hamulec elektryczny 23
- Montaż 23
- Płyta osłony 23
- Regulacja kąta cięcia w poziomie rys 8 23
- Wyłącznik rys 9 23
- Zachowanie maksymalnej wydajności cięcia rys 6 i 7 23
- Zakładanie lub zdejmowanie tarczy 23
- Mocowanie obrabianych elementów 24
- Rys 17 24
- Składanie 24
- Worek na pył rys 16 24
- Konserwacja 25
- Przenoszenie narzędzia 25
- Regulacja kąta cięcia 25
- Regulacja w celu uzyskania płynnej pracy uchwytu 25
- Ce 2003 26
- Makita international europe ltd 26
- Po zakończeniu pracy 26
- Szumy i drgania 26
- Ue deklaracja zgodności 26
- Wymiana szczotek węglowych 26
- Держитесь подальше от детей 27
- Для безопасного функционирования 1 поддерживайте чистоту на рабочем месте 27
- Инструкции по мерам безопасности 27
- Правильно храните неработающие инструменты 27
- Предостережение при использовании электрических инструментов следует всегда соблюдать основные меры безопасности для уменьшения опасности пожара поражения электрическим током и персональных травм включая следующие 27
- Предохраняйтесь от поражения электрическим током 27
- Прочитайте эти инструкции перед тем как пытаться управлять этим изделием и сохраните эти инструкции 27
- Русский язык 27
- Технические характеристики 27
- Учитывайте рабочую окружающую среду 27
- Будьте бдительны 28
- Дополнительные правила безопасности для инструмента 28
- Закрепите рабочее изделие 28
- Избегайте случайных запусков 28
- Используйте для ремонта услуги специалиста 28
- Используйте защитные очки и предохранительные приборы для слуха 28
- Используйте правильный инструмент 28
- Не заходите слишком далеко 28
- Не прилагайте усилие к шнуру 28
- Одевайтесь правильно 28
- Осторожно обращайтесь с инструментами 28
- Отсоединяйте инструменты 28
- Подсоедините пылевсасывающее оборудование 28
- Предостережение 28
- Проверяйте поврежденные части 28
- Шнуры удлинители для использования на улице 28
- Прикрепление к верстаку 29
- Сохраните эти инструкции 29
- Установка 29
- Функциональное описание 29
- Щиток лезвия рис 3 и 4 29
- Действия при переключении рис 9 30
- Доска с пропилом рис 5 30
- Направляющая пластина 30
- Поддержание максимальной режущей способности рис 6 и 7 30
- Регулировка угла отрезки 30
- Сборка 30
- Установка или удаление лезвия пилы 30
- Электрический тормоз 30
- Мешок для пыли 31
- Фиксация рабочего изделия 31
- Эксплуатация 32
- Замена угольных щеток 33
- Обслуживание 33
- Переноска инструмента 33
- После использования 33
- Регулировка для плавной работы рукоятки 33
- Регулировка угла отрезки 33
- Ce 2003 34
- Makita international europe ltd 34
- Ес декларация соответствия 34
- Шум и вибрация 34
Похожие устройства
- Gorenje IT612AC Инструкция по эксплуатации
- Ariston ABS Pro Eco 65 H Slim Инструкция по эксплуатации
- Samsung GT-S8530 Metallic Black Инструкция по эксплуатации
- Hyundai H-CF402 Инструкция по эксплуатации
- Siemens ER 847501E Инструкция по эксплуатации
- Hyundai H-CSW504 Инструкция по эксплуатации
- Timberk WHEX-6 OC Инструкция по эксплуатации
- Gorenje IT612AXC Инструкция по эксплуатации
- Samsung GT-S5570 Dark Grey Инструкция по эксплуатации
- Makita LS 1040 F Инструкция по эксплуатации
- Siemens ER 657502 Инструкция по эксплуатации
- Makita LS 0714 Инструкция по эксплуатации
- Hyundai H-CSK502 Инструкция по эксплуатации
- Diam CSN-355А 620016 Инструкция по эксплуатации
- Gorenje EC57341AX Инструкция по эксплуатации
- Siemens ER 657501E Инструкция по эксплуатации
- Makita LH 1040 Инструкция по эксплуатации
- Hyundai H-CSW694 Инструкция по эксплуатации
- Husqvarna DS40 Gyro 9651576-05 Инструкция по эксплуатации
- Siemens ER 617501E Инструкция по эксплуатации
Скачать
Случайные обсуждения