Ryobi one+ cdc18022n 3000422 [7/127] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ryobi one+ cdc18022n 3000422 [7/127] English

Ryobi one+ cdc18022n 3000422 [7/127] English
4
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
OPERATION
WARNING:
Be prepared for binding at bit breakthrough.
When these situations occur, the drill has a
tendency to grab and kick in the opposite
direction and could cause loss of control when
breaking through material. If not prepared, this
loss of control can result in possible serious
injury.
Q When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
Q When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
Q If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE: This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible
through the vent slots on the housing. This is normal and
is the action of the brake.
WOOD DRILLING
For maximum performance, use high speed steel bits for
wood drilling.
Q Begin drilling at a very low speed to prevent the bit
from slipping off the starting point. Increase the speed
as the drill bit bites into the material.
Q When drilling through holes, place a block of wood
behind the workpiece to prevent ragged or splintered
edges on the back side of the hole.
METAL DRILLING
For maximum performance, use high speed steel bits for
metal or steel drilling.
Q Begin drilling at a very low speed to prevent the bit
from slipping off the starting point.
Q Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much
pressure will:
• Overheat the drill;
• Wear the bearings;
• Bend or burn bits;
• Produce off-center or irregular-shaped holes.
Q When drilling large holes in metal, start with a small
bit, then finish with a larger bit. Also, lubricate the bit
with oil to improve drilling action and increase bit life.
MAINTENANCE
WARNING
When servicing, use only identical Ryobi
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken or
destroy plastic.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as
waste. The machine, accessories and packaging
should be sorted for environmental-friendly
recycling.
SYMBOL
Safety Alert
V Volts
min
-1
Revolutions or reciprocations per minute
Direct current
CE Conformity
Please read the instructions carefully before
starting the machine.
Recycle unwanted
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.

Содержание

Похожие устройства

English OPERATION MAIN NANCE WARNING Be prepared for binding at bit breakthrough When these situations occur the drill has a tendency to grab and kick in the opposite direction and could cause loss of control when breaking through material If not prepared this loss of control can result in possible serious injury When drilling hard smooth surfaces use a center punch to mark the desired hole location This will prevent the drill bit from slipping off center as the hole is started A A WARNING When servicing use only identical Ryobi replacement parts Use of any other parts may create a hazard or cause product damage Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc WARNING Do not at any time let brake fluids gasoline petroleum based products penetrating oils etc come in contact with plastic parts They contain chemicals that can damage weaken or destroy plastic When drilling metals use a light oil on the drill bit to keep it from overheating The oil will prolong the life of the bit and increase the drilling action If the bit jams in the workpiece or if the drill stalls stop the tool immediately Remove the bit from the workpiece and determine the reason for jamming ENVIRONMENTAL PROTECTION NOTE This drill has an electric brake When the switch trigger is released the chuck stops turning When the brake is functioning properly sparks will be visible through the vent slots on the housing This is normal and is the action of the brake Recycle raw materials instead of disposing as waste The machine accessories and packaging should be sorted for environmental friendly recycling WOOD DRILLING SYMBOL For maximum performance use high speed steel bits for wood drilling Safety Alert Begin drilling at a very low speed to prevent the bit from slipping off the starting point Increase the speed as the drill bit bites into the material When drilling through holes place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole V Volts min Revolutions or reciprocations per minute Direct current METAL DRILLING For maximum performance use high speed steel bits for metal or steel drilling Begin drilling at a very low speed to prevent the bit from slipping off the starling point Maintain a speed and pressure which allows cutting without overheating the bit Applying too much pressure will CE Conformity Please read the instructions carefully before starting the machine Recycle unwanted Overheat the drill Wear the bearings Waste electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice Bend or bum bits Produce off center or irregular shaped holes When drilling large holes in metal start with a small bit then finish with a larger bit Also lubricate the bit with oil to improve drilling action and increase bit life 4

Скачать