![APC Smart-UPS SMX3000HVNC [11/21] Function factory default options description](/img/pdf.png)
APC Smart-UPS SMX3000HVNC [11/21] Function factory default options description
![APC Smart-UPS SMX3000HVNC [11/21] Function factory default options description](/views2/1252714/page11/bgb.png)
Smart-UPS X 2000/2200/3000 Vac XL 120/208/230/240 VA Tower/Rack-Mount 4U
9
Configuration
UPS Settings
Start up Settings
Use the display interface to configure these settings at initial start up. The UPS will prompt for a response to each
setting, if no response is given, the default setting will be used.
Note: The UPS will not turn on until all of these settings have been configured.
Function Factory Default Options Description
Language English • English
•French
•German
•Spanish
• Italian
• Portuguese
• Japanese
The language for the display interface.
Language options will vary by model and firmware version.
Output
Voltage
Low Voltage: 120 Vac • 100
•110
• 120
• 127
Set the output voltage while the UPS is in Standby mode.
High Voltage: 230 Vac • 200
• 208
• 220
• 230
• 240
Input Power
Quality
Good • Good
•Fair
•Poor
Select the desired utility power input quality.
• Good: The UPS will go on battery power more often to
provide the cleanest power supply to the connected
equipment.
• Fair: The UPS will tolerate some voltage fluctuations.
• Poor: The UPS will tolerate more voltage fluctuations and
will go on battery power less often.
If unsure of the local power quality, or the connected
equipment is sensitive to voltage fluctuations set the
sensitivity level to Good, using the Advanced menu.
Menu Type Standard Standard or
Advanced
The advanced menus include all parameters. The Standard
menus display a limited set of menus and options.
Date UPS manufacture date
+ 90 days
mm-yyyy Enter the current date.
Содержание
- High voltage 1
- Operation manual 1
- Smart ups 1
- Uninterruptible power supply 1
- Caution 3
- Important safety messages 3
- Inspect the package contents upon receipt notify the carrier and dealer if there is any damage 3
- Overview 3
- Product description 3
- Read the safety guide supplied with this unit before installing the ups 3
- Safety and general information 3
- Battery 4
- For additional specifications refer to the apc by schneider electric web site at www apc com 4
- Humidity 4
- Maximum elevation 4
- Specifications 4
- Temperature 4
- Front panel features 5
- Product overview 5
- Rear panel features 5
- Connect a usb cable from a computer to use power management software note serial and usb communication can only be used individually they cannot be used at the same time 6
- External battery pack optional 6
- Installation 6
- Powerchute network management software 6
- Rear panel features continued 6
- Caution 7
- Connect equipment 7
- Operation 7
- Apc by schneider 8
- Display interface 8
- Display interface operation 8
- Electric 8
- Menu overview 8
- Configuration 9
- Control 9
- Main menu display description standard option advanced option 9
- Status some of these options are displayed as scrolling menus 9
- Main menu display description standard option advanced option 10
- Test diagnostics 10
- Configuration 11
- Function factory default options description 11
- Start up settings 11
- Ups settings 11
- Function factory default options description 12
- General settings 12
- Function factory default options description 13
- Switched outlet groups 14
- Customize switched outlet groups 15
- Function factory default options description 15
- Network management card settings 15
- Caution 16
- Emergency power off 16
- If the epo switch or relay contacts are normally closed insert the wires from the switch or contacts at pins 2 and 3 of the epo terminal block use 16 28 awg wire 16
- If the epo switch or relay contacts are normally open insert the wires from the switch or contacts at pins 1 and 2 of the epo terminal block use 16 28 awg wire 16
- Insert a wire jumper between pins 1 and 2 secure the wires by tightening the three screws at positions 1 2 and 3 16
- Normally closed contacts 16
- Normally open contacts 16
- Overview 16
- Secure the wires by tightening the screws 16
- Display interface leds flash sequentially 17
- Problem and possible cause solution 17
- The fault led is illuminated the ups displays a fault message and emits a constant beeping sound 17
- The ups is operating on battery while connected to input utility power 17
- The ups will not turn on or there is no output 17
- Troubleshooting 17
- Ups does not provide expected backup time 17
- Ups is beeping 17
- All leds are illuminated and the ups is plugged into a wall outlet 18
- Problem and possible cause solution 18
- The display interface shows a site wiring fault message 18
- The replace battery led is illuminated 18
- Service and transport 19
- Limited factory warranty 20
- 2014 en 990 4608b 21
- Apc by schneider electric worldwide customer support 21
Похожие устройства
- APC Smart-UPS SMC3000RMI2U Инструкция по эксплуатации
- APC Line-R LE1200-RS Инструкция по эксплуатации
- APC AP9630 Инструкция по эксплуатации
- APC SurgeArrest PF8VNT3-RS Инструкция по эксплуатации
- APC SurgeArrest P1-RS Инструкция по эксплуатации
- APC Back-UPS BE400-RS Инструкция по эксплуатации
- APC SurgeArrest P5B-RS Инструкция по эксплуатации
- APC Back-UPS BK650EI Инструкция по эксплуатации
- APC Smart-UPS SUA750RMI2U Инструкция по эксплуатации
- Powercom TCA-2000 2000N Инструкция по эксплуатации
- HP SCANJET G3110 Руководство пользователя
- Hansa FCGW53049 Инструкция по эксплуатации
- Hansa FCGW53009 Инструкция по эксплуатации
- Hansa FCGW51109 Инструкция по эксплуатации
- Hansa FCGW50000013 Инструкция по эксплуатации
- Hansa FCGW57001014 Инструкция по эксплуатации
- Hansa FCGX52026 Инструкция по эксплуатации
- Hansa FCGX51029 Инструкция по эксплуатации
- Hansa FCGX53024 Инструкция по эксплуатации
- Bosch TWK 6088 Инструкция по эксплуатации
Скачать
Случайные обсуждения