Chicco Seat-up 012 Grey Инструкция по эксплуатации онлайн [27/204] 219607

Chicco Seat-up 012 Grey Инструкция по эксплуатации онлайн [27/204] 219607
27
26
tractable part of the belt. Completely insert
the belt in the red clamp (L), holding it open
(Fig. 12). Then insert the belt in the specic
light blue belt guide (N) (Fig. 13).
To make the belt as tight as possible, pull the
diagonal portion towards the retractor hold-
ing open the clamp (L) on the opposite side
(that of the buckle) so the belt can slide cor-
rectly (Fig. 14).
WARNING! Check that the child car seat is t-
ted rmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely tted
into the car seat, repeat the installation.
WARNING! Always check that the seat belt
is distributed evenly at all points and that it is
not twisted.
WARNING! NEVER t the car seat belt in any
way not mentioned in these instructions.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
5. HOW TO FIT THE GROUP 1 (9-18 kg)
CHILD CAR SEAT TO THE CAR WITH THE
ISOFIX SYSTEM
WARNING! If the child weighs less than 9 kg
do not use a front-facing car seat.
To t the car seat, remove the Isox connec-
tors (P) by pulling belt (R) towards the exterior
(Fig. 15).
Then remove the Top Tether from the rear cov-
er (S) (Fig. 16).
Position the child car seat on the seat making
reference to the options suggested in your
cars user manual.
Fasten the two ISOFIX connectors (P) to the
corresponding ISOFIX hooks on the car seat
between the backrest and the seat (Fig. 17).
WARNING! Pull the car seat towards you and
then check that the two indicators are green
(Fig. 18) to make sure that the seat has been
installed correctly.
WARNING! Make sure there are no objects
between the child car seat and the vehicle
seat or between the child car seat and car
door.
Push the child car seat rmly against the back-
rest of the car seat (Fig. 19) to make sure it is
securely in place.
The assembly of the child car seat is complet-
ed exclusively with the installation of the Top
Tether (T).
WARNING! Refer to your car’s user manual to
identify where the Top Tether of the child car
sear is attached to the car. This fastening point
is denoted with a specic label (Fig. 20) and
can be found in the positions indicated by the
gures 21A – 21B – 21C – 21D.
WARNING! Check that the Top Tether fasten-
er used is the one that has been specially des-
ignated. Do not confuse it with a ring used for
hanging bags (Fig. 22).
WARNING! Pass the Top Tether between the
top of the car seat backrest and the headrest.
Never pass the Top Tether above the car head-
rest.
Extend the Top Tether belt by pressing adjust-
ment button (V).
Once you have identied the fastening point,
connect to the Top Tether hook (U).
Adjust the length of the Top Tether belt by
forcefully pulling the belt until it is tight. The
indicator on the belt goes green (W) when
the tether is suitably tight (Fig. 23). Roll up any
excess belt and tie up using the velcro.
To disassemble the child car seat, unhook the
Top Tether and the Isox connectors by press-
ing the release buttons (Q) (Fig. 24). To put
them back in completely push them inwards.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
6. HOW TO FIT THE GROUP 1 (9-18 kg)
CHILD CAR SEAT TO THE CAR WITH A
3-POINT SEAT BELT
WARNING! Never t the seat belt in any way
not mentioned in this manual.
The slots for the car seat belts are clearly
marked on the child car seat with red colour
guide items.
Position the child car seat on the selected seat.
WARNING! Make sure there are no objects
between the child car seat and the vehicle
seat or between the child car seat and car
door.
Pull the car seat belt, and slide it through the
space between the backrest and the base of
the child car seat (Fig. 25).
Pass the abdominal part of the cars 3-point
seat belt through the specic red abdominal
belt guides (M). Pull it out from the other side
of the child car seat and fasten it to the buckle
of the seat until you hear a “CLICK” (Fig. 26).
Continue to assemble on the side of the re-
tractable part of the belt. Completely insert
the belt in the red clamp (L), holding it open
(Fig. 27).
After completing the assembly it is necessary
to make the safety harness as tight as possible.
Pull the diagonal part hard towards the retrac-
tor and fasten with the red clamp (L) (Fig. 28).
WARNING! Check that the child car seat is t-
ted rmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely tted
into the car seat, repeat the installation.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
7. HOW TO FIT THE GROUP 2 (15-25 kg)
CHILD CAR SEAT TO THE CAR WITH A
3-POINT SEAT BELT and TOP TETHER
WARNING! Before tting the child car seat
and seating your child, adjust the position of
the child car seat buckle (from A to B) as indi-
cated in paragraph 11. ADJUSTING THE CHILD
CAR SEAT BUCKLE.
Position the child car seat on the selected seat.
WARNING! Make sure there are no objects be-
tween the child car seat and the vehicle seat or
between the child car seat and car door.

Содержание

Похожие устройства

Скачать