Hitachi G23SRU-NS [10/68] Practical grinder application
![Hitachi G 18SR [10/68] Practical grinder application](/views2/1081392/page10/bga.png)
9
English
PRACTICAL GRINDER APPLICATION
1. Pressure
To prolong the life of the machine and ensure a
first class finish, it is important that the machine
should not be overloaded by applying too much
pressure. In most applications, the weight of the
machine alone is sufficient for effective grinding.
Too much pressure will result in reduced rotational
speed, inferior surface finish, and overloading which
could reduce the life of the machine.
2. Grinding angle
Do not apply the entire surface of the depressed
center wheel to the material to be ground. As
shown in Fig. 3, the machine should be held at an
angle of 15° – 30° so that the external edge of the
depressed center wheel contacts the material at an
optimum angle.
3. To prevent a new depressed center wheel from
digging into the workpiece, initial grinding should
be performed by drawing the grinder across the
workpiece toward the operator (Fig. 3 direction B).
Once the leading edge of the depressed center
wheel is properly abraded, grinding may be
conducted in either direction.
4. Switch operation
Switch ON: Push the locking button forward and
then press the switch lever.
* For continuous use, press the switch
lever. The switch lever is locked by
pushing the locking button forward
once again.
(*Subject to change depending on
area.)
Switch OFF: Press and release the switch lever.
5. Precautions immediately after finishing operation
After switching off the machine, do not put it down
until the depressed center wheel has come to a
complete stop. Apart from avoiding serious
accidents, this precaution will reduce the amount
of dust and swarf sucked into the machine.
CAUTIONS
䡬 Check that the work piece is properly supported.
䡬 Ensure that ventilation openings are kept clear when
working in dusty conditions.
If it should become necessary to clear dust, first
disconnect the tool from the mains supply (use non-
metallic objects) and avoid damaging internal parts.
䡬 Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable
substances.
䡬 Always use eye and ear protection.
Other personal protective equipment such as dust
mask, gloves, helmet and apron should be worn
when necessary.
If in doubt, wear the protective equipment.
䡬 When the machine is not use, the power source
should be disconnected.
ASSEMBLING AND DISASSEMBLING THE
DEPRESSED CENTER WHEEL
CAUTION
Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident.
1. Assembling (Fig. 1)
(1) Turn the machine upside down so that the spindle
is facing upward.
(2) Mount the wheel washer onto the spindle.
(3) Fit the protruding part of the depressed center
wheel onto the wheel washer.
(4) Screw the wheel nut onto the spindle.
(5) Insert the push button to prevent rotation of the
spindle, and tighten the wheel nut with the accessory
wrench, as shown in Fig. 1.
2. Disassembling
Follow the above procedures in reverse.
CAUTIONS
䡬 Comfirm that the depressed center wheel is mounted
firmly.
䡬 Confirm that the push button is disengaged by
pushing push button two or three times before
switching the power tool on.
MAINTENANCE AND INSPECTION
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of
cracks and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Inspecting the carbon brushes (Fig. 4)
The motor employs carbon brushes which are
consumable parts.
When they become worn to or near the “wear
limit”, it could result in motor trouble. When an
auto-stop carbon brush is equipped, the motor will
stop automatically.
At that time, replace both carbon brushes with new
ones which have the same carbon brush numbers
shown in the figure. In addition, always keep carbon
brushes clean and ensure that they slide freely
within the brush holders.
4. Replacing carbon brushes
G18SH2
•
G18U2
•
G23SF2
•
G23U2 (Fig. 5)
〈Disassembly〉
(1) Loosen the D4 tapping screw retaining the brush
cover and remove the brush cover.
(2) Use the auxiliary hexagonal wrench or small
screwdriver to pull up the edge of the spring that
is holding down the carbon brush. Remove the
edge of the spring toward the outside of the brush
holder.
(3) Remove the end of the pig-tail on the carbon brush
from the terminal section of brush holder and then
remove the carbon brush from the brush holder.
〈Assembly〉
(1) Insert the end of the pig-tail of the carbon brush
in the terminal section of brush holder.
(2) Insert the carbon brush in the brush holder.
(3) Use the auxiliary hexagonal wrench or small
screwdriver to return the edge of the spring to the
head of the carbon brush.
(4) Mount the tail cover and tighten the D4 tapping
screw.
01Eng_G18SH2_EE 11/30/09, 18:499
Содержание
- ㅃ潶敲彇ㄸ午㉟䕅 p.1
- K l n m p.2
- 䵡牫彇ㄸ午㉟䕅 p.2
- Bceöàa ìaàeçaèúe cpeàcúça áaçëúê öîaá p.5
- Olvasson el minden biztonsági figyelmeztetést és minden utasítást a figyelmeztetések és utasítások be nem tartása áramütést tüzet és vagy súlyos sérülést eredményezhet p.5
- Mindig viseljen védőszemüveget p.5
- Jelölések p.5
- Φ ράτε πάντα τ ν κατάλληλ ε πλισµ για την πρ στασία των µατιών p.5
- Figyelem p.5
- Ì ôï p.5
- Dókkat p.5
- Zawsze nosić okulary ochronne p.5
- Daima koruyucu gözlük takın p.5
- Warnung p.5
- Cëïçoîê p.5
- Warning p.5
- Csak eu országok számára az elektromos kéziszerszámokat ne dobja a háztartási szemétbe a használt villamos és elektronikai készülékekről szóló 2002 96 ek irányelv és annak a nemzeti jogba való átültetése szerint az elhasznált elektromos kéziszerszámokat külön kell gyűjteni és környezetbarát módon újra kell hasznosítani p.5
- Vždy noste ochranu očí p.5
- Always wear eye protection tragen sie immer einen augenschutz p.5
- Upozornění p.5
- Symboly p.5
- Symbols p.5
- Symbole p.5
- Simgeler p.5
- Sadece ab ülkeleri için elektrikli el aletlerini evdeki çöp kutusuna atmayınız kullanılmıß elektrikli aletleri elektrik ve elektronikli eski cihazlar hakkındaki 2002 96 ec avrupa yönergelerine göre ve bu yönergeler ulusal hukuk kurallarına göre uyarlanarak ayrı olarak toplanmalı ve çevre ßartlarına uygun bir ßekilde tekrar deåerlendirmeye gönderilmelidir p.5
- Ostrzeżenie p.5
- 〱䕮束䜱㡓䠲彅 p.6
- General power tool safety warnings p.6
- English p.6
- Safety warnings common for grinding or abrasive cutting off operations p.7
- Kickback and related warnings p.7
- English p.7
- Safety warnings specific for grinding and abrasive cutting off operations p.8
- Precautions on using disc grinder p.8
- English p.8
- Additional safety warnings specific for abrasive cutting off operations p.8
- Standard accessories p.9
- Specifications p.9
- Prior to operation p.9
- English p.9
- Applications p.9
- Practical grinder application p.10
- Maintenance and inspection p.10
- English p.10
- Assembling and disassembling the depressed center wheel p.10
- Guarantee p.11
- English p.11
- 〲䝥牟䜱㡓䠲彅 p.12
- Deutsch p.12
- Allgemeine sicherheitshinweise für elektrogeräte p.12
- Für schleif und trennschleifarbeiten geltende sicherheitshinweise p.13
- Deutsch p.13
- Weitere sicherheitshinweise zu trennschleifarbeiten p.14
- Rückschlag und dazu gehörige sicherheitshinweise p.14
- Deutsch p.14
- Besondere sicherheitshinweise für schleif bzw trennschleifarbeiten p.14
- Vor inbetriebnahme p.15
- Technische daten p.15
- Standardzubehör p.15
- Deutsch p.15
- Anwendungsgebiete p.15
- Vorsichtsmassnahmen bei der benutzung des winkelschleifers p.15
- Praktische schleifarbeit p.16
- Deutsch p.16
- Wartung und inspektion p.17
- Garantie p.17
- Deutsch p.17
- Anbringen und abnehmen der schleifscheibe p.17
- Deutsch p.18
- 〳䝲敟䜱㡓䠲彅 p.19
- Π ƒ π π π º π ƒπ à ƒ π à p.19
- Ïïëóèî p.19
- Ƒ π π π º π π π ƒ ãπ ª ƒ ãà ƒπ π ª p.20
- Ïïëóèî p.20
- Ƒ π π π º π π π π ƒ ãπ ª ƒ ãà ƒπ π ª p.21
- Ƒ ƒ π π π º π π π π ƒ ãπ ª ƒ ãà ƒπ π ª p.21
- Ïïëóèî p.21
- Π ª π ã π ƒ π π π p.21
- Π ƒ ª p.22
- Ƒπ π àƒ π p.22
- Ƒ ºà π ª ƒ ø ムà π à π p.22
- Ïïëóèî p.22
- Ã π ã ƒ ƒπ π p.22
- º ƒª p.22
- Ƒ π º ƒª à π p.23
- Ïïëóèî p.23
- Ïïëóèî p.24
- À ƒª π à ƒª à ã ª øª à ƒπ ƒ ã à p.24
- À ƒ π ã p.24
- Ïïëóèî p.25
- 〴偯江䜱㡓䠲彅 p.26
- Polski p.26
- Ogólne wskazówki bezpieczeństwa dotyczące urządzeń elektrycznych p.26
- Polski p.27
- Ogólne wskazówki bezpieczeństwa dotyczące prac szlifierskich i cięcia p.27
- Wskazówki bezpieczeństwa dotyczące szlifowania i ścierania p.28
- Polski p.28
- Ostrzeżenia dotyczące odrzutu oraz podobnych zagrożeń p.28
- Dodatkowe wskazówki bezpieczeń stwa dotyczące prac związanych z przecinaniem p.28
- Środki ostrożności przy używaniu szlifierki tarczowej p.29
- Zastosowanie p.29
- Wyposażenie standardowe p.29
- Przed użyciem p.29
- Polski p.29
- Dane techniczne p.29
- Składanie i rozkładanie obniżonych tarcz śsrodkowych p.30
- Praktyczne zastosowanie szlifierki p.30
- Polski p.30
- Gwarancja p.31
- Polski p.31
- Konserwacja i inspekcja p.31
- 〵䡵湟䜱㡓䠲彅 p.32
- Szerszámgépekre vonatkozó általános biztonsági figyelmeztetések p.32
- Magyar p.32
- Magyar p.33
- Biztonsági figyelmeztetések csiszoló és vágó műveletekhez p.33
- Visszarúgás és az arra vonatkozó figyelmeztetések p.34
- Magyar p.34
- Kiegészítő biztonsági figyelmeztetések a daraboló műveletre vonatkozóan p.34
- Biztonsági figyelmeztetések csiszolásra és a darabolási folyamatra vonakozóan p.34
- A tárcsás kéziköszörű használatára vonatkozó óvintézkedések p.34
- Magyar p.35
- Az üzembehelyezés előtti tennivalók p.35
- Alkalmazások p.35
- A kéziköszörű gyakorlati kezelése p.35
- Műszaki adatok p.35
- Magyar p.36
- Ellenőrzés és karbantartás p.36
- A süllyesztett közepű tárcsa összeszerelése és szétszerelése p.36
- Magyar p.37
- Garancia p.37
- 䍺敟䜱㡓䠲彅 p.38
- Čeština p.38
- Obecná varování týkající se bezpečnosti el přístroje p.38
- Čeština p.39
- Kopnutí a s tím související varování p.39
- Bezpečnostní varování společná pro broušení a odřezávání p.39
- Čeština p.40
- Upozornění pro používání kotoučové brusky p.40
- Dodatečná bezpečnostní varování specifická pro řezání p.40
- Bezpečnostní varování specifická pro broušení a řezání p.40
- Čeština p.41
- Standardní příslušenství p.41
- Před použitím p.41
- Praktické použití brusky p.41
- Použití p.41
- Parametry p.41
- Čeština p.42
- Údržba a kontrola p.42
- Montáž a demontáž brusného kotouče p.42
- Čeština p.43
- Záruka p.43
- 呵牟䜱㡓䠲彅 p.44
- Türkçe p.44
- Genel elektrókló alet güvenlók uyarilari p.44
- Taílama veya aíindirarak kesme óílemleró óçón genel güvenlók uyarilari p.45
- Geró tepme ve ólgóló uyarilar p.45
- Türkçe p.45
- Türkçe p.46
- Taílama ve aíindirarak kesme óílemleró óçón özel güvenlók uyarilari p.46
- Dósk taílama aletónó kullanirken alinacak önlemler p.46
- Aíindirarak kesme óílemleró óçón özel ólave güvenlók uyarilari p.46
- Uygulamalar p.47
- Türkçe p.47
- Teknók özellókler p.47
- Standart aksesuarlar p.47
- Pratók taílama uygulamalari p.47
- Aletó kullanim öncesónde p.47
- Türkçe p.48
- Tek tarafi oyuk taílama dóskónón takilip çikarilmasi p.48
- Bakim ve ónceleme p.48
- Türkçe p.49
- Garantó p.49
- 〸創獟䜱㡓䠲彅 p.50
- Pyccíëè p.50
- Oåôàe èpabàãa åeâoèachoctà èpà paåote c ùãektpoàhctpìmehtom p.50
- Pyccíëè p.51
- Oåôàe èpeñyèpeüñehàü oå octopoühoctà ñãü èpobeñehàü òãàîobaãúhõx paåot àãà otpeâahàü p.51
- Pyccíëè p.52
- Otñaóa à ñpìéàe èoxoüàe èpeñìèpeüñehàü p.52
- Ocoåõe mepõ èpeñoctopoühoctà ñãü peüìôàx paåot à aåpaâàbhoâ otpeâkà p.52
- Pyccíëè p.53
- Ñoèoãhàteãúhõe ocoåõe mepõ èpeñoctopoühoctà ñãü aåpaâàbhoâ otpeâkà p.53
- Mepõ èpeñoctopoühoctà èpà ùkcèãìatañàà òãàîobaãúhoâ maòàhõ p.53
- Èoñéotobka k ùkcèãìatañàà p.54
- Texhàóeckàe xapaktepàctàkà p.54
- Pyccíëè p.54
- Oåãactú èpàmehehàü p.54
- Ctahñapthõe akceccìapõ p.54
- Ìctahobka à chütàe òãàîobaãúhoéo kpìéa c ìtoèãehhõm ñehtpom p.55
- Èpaktàóeckoe èpàmehehàe òãàîobaãúhoâ maòàhõ p.55
- Pyccíëè p.55
- Éapahtàü p.56
- Texhàóeckoe oåcãìüàbahàe à èpobepka p.56
- Pyccíëè p.56
- Pyccíëè p.57
- 〹䉡捫彇ㄸ午㉟䕅 p.58
- G18sh2 p.58
- G23sf2 p.59
- G18sru p.60
- G23sru p.61
- Hitachi power tools polska sp z o o p.67
- Hitachi power tools netherlands b v moscow branch p.67
- Hitachi power tools hungary kft p.67
- Hitachi power tools czech s r o p.67
- Hitachi power tools österreich gmbh p.67
- Hitachi power tools romania p.67
- Technical file at p.68
- Siemensring 34 47877 willich 1 f r germany p.68
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan p.68
- Representative office in europe p.68
- K kato board director p.68
- Hitachi power tools europe gmbh p.68
- Hitachi koki europe ltd p.68
- Hitachi koki co ltd p.68
- Head office in japan p.68
- Code no c99107295 e printed in ireland p.68
- Clonshaugh business technology park dublin 17 lreland p.68
Похожие устройства
-
Hitachi G23SW-NPИнструкция по эксплуатации -
Hitachi G13SN-NUИнструкция по эксплуатации -
Hitachi G23SR-NSИнструкция по эксплуатации -
Hitachi G13SD-NSИнструкция по эксплуатации -
Hitachi G13SS-NUИнструкция по эксплуатации -
Hitachi G18ST-NUИнструкция по эксплуатации -
Hitachi G23MRU-NBИнструкция по эксплуатации -
Hitachi G12SW-NSИнструкция по эксплуатации -
Hitachi G23ST-NUИнструкция по эксплуатации -
Hitachi G18ST-NSИнструкция по эксплуатации -
Hitachi G13YD-LAИнструкция по эксплуатации -
Hitachi G23UCY-NSИнструкция по эксплуатации