![Hitachi CG40EAFNE [10/84] English](/img/pdf.png)
Hitachi CG40EAFNE [10/84] English
![Hitachi CG40EAFNE [10/84] English](/views2/1368477/page10/bga.png)
10
English
ASSEMBLY PROCEDURES
Drive shaft to fl exible shaft (Fig. 1)
Remove tube locking bolt (1).
Insert unholed end of fl exible shaft (2) into joint pipe of drive shaft
(3) to the end and tighten the tube locking bolt by engaging the bolt
to the slot of fl exible shaft.
NOTE
Make sure to align square end of fl exible inner shaft with square
hole of drive shaft by slightly rotating drive shaft so that they are
connected fi rmly.
Flexible shaft to engine (Fig. 2)
Pull up lock-pin (4).
Insert holed end of fl exible shaft into clutch case to the end by
rotating slightly.
Release lock-pin to lock in the location hole (22).
Installation of handle
WARNING
When you use steel/rigid blades on brush cutters, always use
a barrier bar (5) and shoulder harness with the loop handle.
(Fig. 3)
Attach the handle to the drive shaft tube with the angle towards the
engine.
Adjust the location to the most comfortable position before
operation.
Throttle wire / stop cord
Remove air cleaner cover. (Fig. 4)
Connect stop cords. (Fig. 5)
Insert the stay (6) under the nut (7) screwed onto the outer end of
the throttle wire (8) and connect the end of the throttle wire (9) to the
carburetor (10). Then tighten the nut (7) to secure the throttle wire to
the stay (6). (Fig. 6)
NOTE
Check that the carburetor throttle returns to the idle position
and also that it can be opened wide by operating the throttle
lever.
Cover throttle wire and stop cords together with protective tube
provided up to air cleaner cover. (Fig. 7)
Some models may come with the throttle wire and stop cords
already installed.
Installation of gear case cover (Fig. 8)
Attach the gear case cover (11) with the three screws, making sure
to align the notch (12) in the gear case with the hole (13) in the gear
case cover.
Installation of blade guard (Fig. 9)
The guard bracket already mounted to the drive shaft tube.
Install the blade guard on drive shaft tube against angle
transmission (14). Tighten the guard bracket fi rmly so that the blade
guard does not swing or move down during operation.
CAUTION
The blade guard must be in place during operation.
If the blade guard is not in place, there is a possibility of serious
injury.
Guard extension are equipped with sharp line limiter. Be careful
with handling it.
Installation of cutting blade (Fig. 12)
When installing a cutting blade, make sure that there are no cracks
or any damage in it and that the cutting edges are facing the correct
direction.
Align the notch hole of the cutter holder with the hole on the gear
case cover and insert the Allen wrench to stop turning. Turn the
fi xing nut clockwise and remove the fi xing nut, protection cover,
cutter holder cap, and toothed lock washers.
The installation of the cutting blade is as follows: insert the Allen
wrench into the notch hole of the cutter holder and the hole on
the gear case. Then, install the cutting blade (check the installing
direction, as referring to Fig. 14), the cutter holder cap, protection
cover and toothed lock washers onto the cutter holder in this order.
Finally, tighten the fi xing nut securely by turning counterclockwise
with the Combi box spanner. (Fig. 12)
CAUTION
○ When installing the cutting blade, set its center hole to the
convex part of the cutter holder and hold it with the concave
surface of the cutter holder cap. Then, tighten the fi xing nut to
prevent the cutting blade from being eccentric. (Fig. 12)
After installing the cutting blade, be sure to remove the Allen
wrench and Combi box spanner.
○ Before operation, make sure the blade has been properly
installed. (Fig. 13)
○ Before operation, check the cutter holder cap under the cutting
blade for wear or cracks. If any damage or wear is found,
replace it, as it is an article of consumption.
NOTE
The blade must be retained with a new cotter pin each time
installed. (Fig. 12)
Installation of nylon head (Fig. 15)
If your unit has nylon head, follow the installation.
Attach cutter holder (15) to the gear case. Insert an Allen wrench
into the hole in the gear case to attach winding protector (16) and
attach nylon head (17) by turning it clockwise.
NOTE
○ Since cutter holder cap is not used here, keep it for next metal
blade use.
○ To attach the guard extension, refer to the drawings. Wear
gloves as the extension has a sharp line limiter, then push the
guard extension to blade guard when make sure put on two
tabs.
After attach the screw. (Fig. 10, 11)
OPERATING PROCEDURES
Fuel (Fig. 16)
WARNING
○ The backpack brush cutter is equipped with a two-stroke
engine. Always run the engine on fuel, which is mixed with oil.
Provide good ventilation, when fueling or handling fuel.
○ Fuel is highly fl ammable and toxic and can result in serious
injury if it is inhaled or comes into contact with your skin. Always
handle fuel with care. Always have good ventilation when
handling fuel inside building.
Fuel
○ Always use branded 89 octane unleaded gasoline.
○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1,
please consult the oil bottle for the ratio or Hitachi dealer.
○ If genuine oil is not available, use an anti-oxidant added quality
oil expressly labeled for air-cooled 2-cycle engine use (JASO
FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW
(2-stroke water-cooling type) mixed oil.
○ Never use multi-grade oil (10 W/30) or waste oil.
○ Always mix fuel and oil in a separate clean container.
Always start by fi ling half the amount of fuel, which is to be used.
Then add the whole amount of oil. Mix (shake) the fuel mixture. Add
the remaining amount of fuel.
Mix (shake) the fuel-mix thoroughly before fi lling the fuel tank.
Fueling
WARNING
○ Always shut off the engine before refueling.
○ Slowly open the fuel tank, when fi lling up with fuel, so that
possible over-pressure disappears.
○ Tighten the fuel cap carefully, after fueling.
○ Always move the brush cutter at least 3 m from the fueling area
before starting.
○ Always wash any spilled fuel from clothing immediately with
soap.
○ Be sure to check for any fuel leakage after refueling.
000Book_CG40EAF_EE.indb 10000Book_CG40EAF_EE.indb 10 2010/04/19 18:51:412010/04/19 18:51:41
Содержание
- Backpack brush cutter 1
- Cg 40eaf lp 1
- Plecakowa kosa spalinowa 1
- Rückentragbare motorsense 1
- Sırt çantası çalı kesicisi motocoasa cu ax fl exibil nahrbtna motorna kosa 1
- English 6
- Meanings of symbols 6
- Original instructions 6
- English 7
- What is what 7
- English 8
- Warnings and safety instructions 8
- English 9
- Specifications 9
- Assembly procedures 10
- English 10
- Operating procedures 10
- English 11
- Maintenance 11
- English 12
- Deutsch 13
- Symbolbedeutungen 13
- Übersetzung der original gebrauchsanweisung 13
- Deutsch 14
- Teilebezeichnungen 14
- Deutsch 15
- Warn und sicherheitshinweise 15
- Deutsch 16
- Technische daten 16
- Betrieb 17
- Deutsch 17
- Zusammenbau 17
- Deutsch 18
- Wartung 18
- Deutsch 19
- Deutsch 20
- Ω χ ώ ώ 21
- Polski 29
- Tłumaczenie oryginalnych instrukcji 29
- Znaczenie symboli 29
- Polski 30
- Zasadnicze podzespoły urządzenia 30
- Ostrzeżenie i instrukcje bezpieczeństwa 31
- Polski 31
- Polski 32
- Specyfikacje 32
- Polski 33
- Procedury montażu 33
- Procedury obsługi 33
- Konserwacja 34
- Polski 34
- Polski 35
- A szimbólumok jelentése 36
- Fordítás az eredeti útmutatót 36
- Magyar 36
- Magyar 37
- Mi micsoda 37
- Figyelmeztetések és biztonsági óvintézkedések 38
- Magyar 38
- Magyar 39
- Műszaki adatok 39
- Magyar 40
- Működtetési eljárások 40
- Összeszerelési eljárások 40
- Karbantartás 41
- Magyar 41
- Magyar 42
- Překlad původních pokynů 43
- Význam symbolů 43
- Čeština 43
- Co je co 44
- Čeština 44
- Varování a bezpečnostní pokyny 45
- Čeština 45
- Specifikace 46
- Čeština 46
- Montážní postupy 47
- Pracovní postupy 47
- Čeština 47
- Údržba 48
- Čeština 48
- Čeština 49
- Asıl talimatların çevirisi 50
- Sembollerхn anlamlari 50
- Türkçe 50
- Tanimlar 51
- Türkçe 51
- Türkçe 52
- Uyarilar ve güvenlхk talхmatlari 52
- Teknхk özellхkler 53
- Türkçe 53
- Montaj хşlemlerх 54
- Türkçe 54
- Çaliştirma 54
- Türkçe 55
- Türkçe 56
- Românσ 57
- Sensul simbolurilor 57
- Traducerea instrucţiunilor originale 57
- Ce şi ce este 58
- Românσ 58
- Avertismente şi instrucţiuni de siguranţф 59
- Românσ 59
- Românσ 60
- Specificaţii 60
- Mod de asamblare 61
- Mod de exploatare 61
- Românσ 61
- Românσ 62
- Întreţinere 62
- Românσ 63
- Pomen simbolov 64
- Prevod originalnih navodil 64
- Slovenščina 64
- Opis delov 65
- Slovenščina 65
- Opozorila in varnostna navodila 66
- Slovenščina 66
- Slovenščina 67
- Specifikacije 67
- Postopek montaže 68
- Postopek upravljanja 68
- Slovenščina 68
- Slovenščina 69
- Vzdrževanje 69
- Slovenščina 70
- Book_cg40eaf_ee indb 84 000book_cg40eaf_ee indb 84 2010 04 19 18 51 48 2010 04 19 18 51 48 84
- Code no e99005791 g printed in china 84
- Declaraţie de conformitate ce 84
- Deklaracja zgodności z ec 84
- Deutsch erklärung zur konformität mit ce regeln türkçe ab uygunluk beyani 84
- Ec deklaracija o skladnosti 84
- English ec declaration of conformity čeština prohlášení o shodě s ce 84
- Eu megfelelőségi nyilatkozat 84
- Head offi ce in japan hitachi koki co ltd shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 84
- Hitachi koki co ltd 84
- K kato board birector 84
- Magyar 84
- Polski 84
- Representative offi ce in europe hitachi power tools europe gmbh siemensring 34 47877 willich 1 f r germany 84
- Românσ 84
- Slovenščina 84
- Technical fi le at hitachi koki europe ltd clonshaugh business technology park dublin 17 lreland 84
- Η ω η 84
Похожие устройства
- Калибр БП-1500/16У 57835 Руководство по эксплуатации
- Patriot PS 2300 Е 426302222 Инструкция по эксплуатации
- Grundfos UPS 25-60 130 96281476 Инструкция по эксплуатации
- Karcher K 5 Premium 1.181-313.0 Инструкция по эксплуатации
- Grundfos UPS 32-60 180 96281496 Инструкция по эксплуатации
- Grundfos ALPHA2 25-60 180 98520749 Инструкция по эксплуатации
- Grundfos UPS 25-40 180 96281375 Инструкция по эксплуатации
- Grundfos UP 20-30 N 150 59643500 Инструкция по эксплуатации
- Grundfos SB 3-35 A 97686701 Инструкция по эксплуатации
- Grundfos UP 20-15 N 150 59641500 Инструкция по эксплуатации
- Hitachi CG31EBSNB Инструкция по эксплуатации
- Gardena EasyCut Li-18/23R 09823-55.000.00 Инструкция по эксплуатации
- Fubag PG 600 568713 Инструкция по эксплуатации
- СОЮЗ НГС-97128Н Инструкция по эксплуатации
- Bosch 250мм (10") 3397011965 Инструкция по эксплуатации
- SKAD R15 6J PCD4x114.3 ET38 D67.1 1302005 Инструкция по эксплуатации
- SKAD R13 5.5J PCD4x98 ET35 D58.6 1340008 Инструкция по эксплуатации
- SKAD R15 6J PCD4x100 ET50 D60.1 1021208 Инструкция по эксплуатации
- SKAD R16 6J PCD4x114.3 ET46 D67.1 1690308 Инструкция по эксплуатации
- SKAD R18 7.5J PCD5x108 ET49 D67.1 1621005 Инструкция по эксплуатации