Home
Главная
Hotpoint-Ariston
Плиты
CG 64 SG3 R/HA
Инструкция по эксплуатации Страница: 18

Hotpoint-Ariston CG 64 SG3 R/HA [18/68] Adapting to different types of gas

 Is easy to inspect along its whole length so that its

condition may be checked.

 Is shorter than 1500 mm.

 Fits firmly into place at both ends, where it will be

fixed using clamps that comply with current

regulations.

! If one or more of these conditions is not fulfilled or if the

cooker must be installed according to the conditions

listed for class 2 - subclass 1 appliances (installed

between two cupboards), the flexible steel hose must be

used instead (see below).

Connecting a flexible jointless stainless steel pipe

to a threade d attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is

a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and

does not come into contact with moving parts.

Checking the

tightness of the connection

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a

7 mm socket spanner (see

figure), and replace them with

nozzles suited to the new type

of gas (see Burner and nozzle

specifications table).

3. Replace all the components

by following the above

instructions in reverse.

Adjusting the hob burners minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until

the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible.

3. While the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame is not extinguished.

! The hob burners do not require primary air adjustment.

Adapting the oven

Replacing the oven burner nozzle:

1. Open the oven door fully

2. Pull out the sliding oven

bottom (see diagram).

3. Remove the oven burner

after unscrewing the screws V

(see figure).

4. Unscrew the nozzle using a

special nozzle socket spanner

(see figure) or with a 7 mm

socket spanner, and replace it

with a new nozzle that is suited

to the new type of gas (see

Burner and nozzle specifications

table).

Adjusting th

e gas oven burners minimum setting:

1. Light the burner (see Start-up and Use).

2. Turn the knob to the minimum position (MIN) after it

has been in the maximum position (MAX) for

approximately 10 minutes.

3. Remove the knob.

4. Tighten or loosen the adjustment screws on the

outside of the thermostat pin (see figure) until the

flame is small but steady.

! In the case of natural gas, the adjustment screw must be

unscrewed by turning it anti-clockwise.

Содержание

Похожие устройства

GB Is easy to inspect along its whole length so that its condition may be checked Is shorter than 1500 mm Fits firmly into place at both ends where it will be fixed using clamps that comply with current regulations If one or more of these conditions is not fulfilled or if the cooker must be installed according to the conditions listed for class 2 subclass 1 appliances installed between two cupboards the flexible steel hose must be used instead see be oU Adjusting the hob burners minimum setting 1 Turn the tap to the minimum position 2 Remove the knob and adjust the regulatory screw which is positioned inside or next to the tap pin until the flame is small but steady If the appliance is connected to a liquid gas supply the regulatory screw must be fastened as tightly as possible 3 While the burner is alight quickly change the position of the knob from minimum to maximum and vice versa several times checking that the flame is not extinguished The hob burners do not require primary air adjustment Connecting a flexible jointless stainless steel pipe to a threaded attachment Adapting the oven Make sure that the hose and gaskets comply with current national legislation To begin using the hose remove the hose holder on the appliance the gas supply inlet on the appliance is a cylindrical threaded 1 2 gas male attachment Replacing the oven burner nozzle 1 Open the oven door fully 2 Pull out the sliding oven bottom see diagram Perform the connection in such a way that the hose length does not exceed a maximum of 2 metres making sure that the hose is not compressed and does not come into contact with moving parts Checking the tightness of the connection When the installation process is complete check the hose fittings for leaks using a soapy solution Never use a flame 3 Remove the oven burner after unscrewing the screws V see figure Adapting to different types of gas It is possible to adapt the appliance to a type of gas other than the default type this is indicated on the rating label on the cover Adapting the hob Replacing the nozzles for the hob burners 1 Remove the hob grids and slide the burners off their seats 2 Unscrew the nozzles using a 7 mm socket spanner see figure and replace them with nozzles suited to the new type of gas see Burner and nozzle specifications table 3 Replace all the components by following the above instructions in reverse 18 4 Unscrew the nozzle using a special nozzle socket spanner see figure or with a 7 mm socket spanner and replace it with a new nozzle that is suited to the new type of gas see Burner and nozzle specifications table Adjusting the gas oven burner s minimum setting 1 Light the burner see Start up and Use 2 Turn the knob to the minimum position MIN after it has been in the maximum position MAX for approximately 10 minutes 3 Remove the knob 4 Tighten or loosen the adjustment screws on the outside of the thermostat pin see figure until the flame is small but steady In the case of natural gas the adjustment screw must be unscrewed by turning it anti clockwise

Скачать

Случайные обсуждения

Ответы 1

Как снизить температуру у духовки?

4 года назад

Ответы 1

Какой срок службы у данной газовой плиты? Дата изготовления 04.2007 года.

3 года назад

Ответы 1

Как поджечь духовку сразу и низ и верх

8 месяцев назад