Home
Главная
Skil
Мойки Высокого Давления
0760 RA (F 015 076 0RA)
Инструкция по эксплуатации Страница: 7

Skil 0760 RA (F 015 076 0RA) [7/104] Application advice

• Ensure that all current-conducting components in the

working area are protected against splashed water

• Keep cord connections dry and o ground

• Inspect the cord periodically and have it replaced by a

qualied person, if damaged

• Do not run over, crush or pull the (extension) cord

• Protect the (extension) cord from heat, oil and sharp

edges

• Only use an extension cord which is intended for outdoor

use and equipped with a watertight plug and coupling-

socket

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Only use extension cords with a maximum length of 20

metres (1,5 mm²) or 50 metres (2,5 mm²)

• Inspect the extension cord periodically and replace it, if

damaged (inadequateextensioncordscanbe

dangerous)

• Never touch the mains plug with wet hands

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (donottouchthecord

beforedisconnectingtheplug)

• When connecting a new plug, pay attention to the

following (U.K. only):

- plugs and sockets conforming to BS 4243 or BS 196

should be used wherever practicable

- domestic pattern plugs to BS 1363 are not

recommended, but if their use is essential, those

which have barriers or moulded channels inside

should be selected, so that, if the earth continuity

conductor is pulled out of its terminal, it is unlikely to

be able to touch the phase terminal of the fuse carrier

- domestic pattern plugs to BS 546 should not be used

- the wiring of the plug should leave more slack in the

earth continuity conductor than in the other cores, so

that it is not the rst core to be pulled out of its

terminal, should the cord grip fail

- plugs which have good grips capable of maintaining a

rm hold on the cable sheath should be selected

- in general, additional means should be provided to

relieve stress on cable terminations in the plug (for

example, additional cable clamps should be tted or a

substantial chain could be used to tether the machine

to a xed point)

- plugs and sockets situated near the work site or

outdoors should be to class IP 55 of BS 5490 to

provide adequate protection against ingress of water,

etc. and cable entries require eective sealing

- rubber shrouds should be provided over cable glands

- drip-proof (class IP X2 of BS 5490) plugs and sockets

to BS 4343 are suitable for use indoors where the plug

is away from the water spray area where the appliance

is in use

USE

• Assembly instructions 6

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the high-pressure washer

- as a safety precaution press trigger lock A to avoid that

trigger B is activated accidentally

• Connection to water supply 7

- screw inlet connector C onto water inlet D

! neveruseinletconnectorCwithoutwaterfilterE

- attach water supply hose (not supplied) to water tap

and inlet connector C

! ensurethatthetemperatureoftheincomingwater

doesnotexceed40°C (on a hot day run the water until

it cools down before connecting to water tap)

• Operating the tool 8

- ensure that the tool is placed on a solid base and in

vertical position

- connect the tool to the mains supply (ensure that

mains switch F is in the o-position)

- open water tap

- press trigger lock A to release trigger B

- fully press trigger B to release any trapped air from the

tool or the water supply hose

- release trigger B and press trigger lock A

- switch on the tool by pressing button “I” of mains switch F

- after switching on the motor starts running for a few

seconds until maximum pressure is reached

- press trigger lock A, point spraying nozzle G at the

area to be washed and then pull trigger B

- switch between a concentrated jet of water and a wide

spray by turning nozzle G

- upon release of trigger B the motor stops running after

a few seconds when maximum pressure is reached

- switch o the tool by pressing button “O” of mains

switch F

- close water tap

- fully press trigger B until there is no more water

pressure in the tool

- after use press trigger lock A to avoid that trigger B is

activated accidentally

! disconnectplugfrompowersourceandensure

thatthecuttingbladehasstoppedrotating

- disconnect water supply hose from tool and water tap

• Use of detergent bottle 9

! ensurethattriggerislockedandmainsswitchis

intheoff-position

- unscrew bottle H from detergent nozzle J and ll it with

biodegradable detergent suitable for high-pressure

washer application (theuseofotherdetergentsor

chemicalsmayadverselyaffectthesafetyofthe

tool)

! donotuseundiluteddetergents

- screw lled bottle H onto detergent nozzle J

- remove lance K from hand gun L and mount detergent

nozzle J instead as illustrated

- press trigger lock A, point detergent nozzle J at the

area to be washed and then pull trigger B

! detergentdoesnotcomeoutunderhighpressure

APPLICATIONADVICE

• When using detergent bottle H

! readthedetergentlabelforadditional

instructions

- always wet the object rst

- apply detergent to the object from the bottom up

- give the detergent time to work, but never leave it to dry

- rinse from top and work downwards

• For more tips see www.skil.com

Содержание

Похожие устройства

Ensure that all current conducting components in the working area are protected against splashed water Keep cord connections dry and oft ground Inspect the cord periodically and have it replaced by a qualified person if damaged Do not run over crush or pull the extension cord Protect the extension cord from heat oil and sharp edges Only use an extension cord which is intended for outdoor use and equipped with a watertight plug and coupling socket Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps Only use extension cords with a maximum length of 20 metres 1 5 m m2 or 50 metres 2 5 mm2 Inspect the extension cord periodically and replace it if damaged Inadequate extension cords can be dangerous Never touch the mains plug with wet hands Always switch off tool and disconnect plug from power source if the power supply cord or the extension cord is cut damaged or entangled do not touch the cord before disconnecting the plug When connecting a new plug pay attention to the following U K only plugs and sockets conforming to BS 4243 or BS 196 should be used wherever practicable domestic pattern plugs to BS 1363 are not recommended but if their use is essential those which have barriers or moulded channels inside should be selected so that if the earth continuity conductor is pulled out of its terminal it is unlikely to be able to touch the phase terminal of the fuse carrier domestic pattern plugs to BS 546 should not be used the wiring of the plug should leave more slack in the earth continuity conductor than in the other cores so that it is not the first core to be pulled out of its terminal should the cord grip fail plugs which have good grips capable of maintaining a firm hold on the cable sheath should be selected in general additional means should be provided to relieve stress on cable terminations in the plug for example additional cable clamps should befitted or a substantial chain could be used to tether the machine to a fixed point plugs and sockets situated near the work site or outdoors should be to class IP 55 of BS 5490 to provide adequate protection against ingress of water etc and cable entries require effective sealing rubber shrouds should be provided over cable glands drip proof class IP X2 of BS 5490 plugs and sockets to BS 4343 are suitable for use indoors where the plug is away from the water spray area where the appliance is in use Connection to water supply screw inlet connector C onto water inlet D I never use Inlet connector C without water filter E attach water supply hose not supplied to water tap and inlet connector C I ensure that the temperature of the Incoming water does not exceed 40 C on a hot day run the water until it cools down before connecting to water tap Operating the tool ensure that the tool is placed on a solid base and in vertical position connect the tool to the mains supply ensure that mains switch F is in the off position open water tap press trigger lock A to release trigger B fully press trigger B to release any trapped air from the tool or the water supply hose release trigger B and press trigger lock A switch on the tool by pressing button I of mains switch F after switching on the motor starts running for a few seconds until maximum pressure is reached press trigger lock A point spraying nozzle G at the area to be washed and then pull trigger B switch between a concentrated jet of water and a wide spray by turning nozzle G upon release of trigger B the motor stops running after a few seconds when maximum pressure is reached switch off the tool by pressing button O of mains switch F close water tap fully press trigger B until there is no more water pressure in the tool after use press trigger lock A to avoid that trigger B is activated accidentally I disconnect plug from power source and ensure that the cutting blade has stopped rotating disconnect water supply hose from tool and water tap Use of detergent bottle I ensure that trigger is locked and mains switch Is In the off position unscrew bottle H from detergent nozzle J and fill it with biodegradable detergent suitable for high pressure washer application the use of other detergents or chemicals may adversely affect the safety of the tool I do not use undiluted detergents screw filled bottle H onto detergent nozzle J remove lance K from hand gun L and mount detergent nozzle J instead as illustrated press trigger lock A pointdetergentnozzle Jatthe area to be washed and then pull trigger B I detergent does not come out under high pressure USE When using detergent bottle H I read the detergent label for additional Instructions always wet the obj ect first apply detergent to the object from the bottom up give the detergent time to work but never I eave it to dry rinse from top and work downwards For more tips see www skil com APPLICATION ADVICE Assembly instructions the sequence of the numbers appearing in the drawing corresponds with the sequence of the steps to be followed for assembl Ing the hi gh pressure washer as a safety precaution press trigger lock A to avoid that trigger B is activated accidentally 7

Скачать