Home
Главная
Skil
Мойки Высокого Давления
0760 RA (F 015 076 0RA)
Инструкция по эксплуатации Страница: 8

Skil 0760 RA (F 015 076 0RA) [8/104] Declaration of conformity c

MAINTENANCE/SERVICE

• This tool is not intended for professional use

• Beforemaintenancealwaysswitchofftool,ensure

thereisnowaterpressureintoolandhandgun,

disconnectplugfrompowersource,anddisconnect

toolfromwatersupply

• Always keep tool and cord clean (especially ventilation

slots S 2)

- do not use water, solvents or polishes

- regularly clean spraying nozzle G using cleaning

needle M 0 (remove spray lance K from hand gun L

rst)

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• Cleaning water lter

- remove water lter E 2 from inlet connector C 2 with

long nose pliers

- rinse it clean and put it back (replace it when

damaged)

! neverusethetoolwithadamagedwaterfilter

• Storage !

- store the tool out of reach of children in a location

where the ambient temperature will not exceed 40°C

or drop below 0°C

- do not place other objects on top of the tool

- securely mount storage rail N on the wall with 4 screws

(notsupplied) and horizontally leveled

- use storage rail N and storage straps P as illustrated

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switchoffthetoolanddisconnecttheplugbefore

investigatingtheproblem

★ Spray is not consistent

- nozzle partly blocked -> clean nozzle

★ Motor does not start or stops suddenly

- power supply socket faulty -> use another socket

- plug not connected -> connect plug

- thermal protection switched o the motor -> let the tool

cool down for 5 minutes

★ Motor is running but spray is poor

- nozzle completely blocked -> clean nozzle

- water lter clogged -> clean water lter

- air in the pump -> ensure that water inlet connector is

securely tted

- inadequate water supply -> check that water tap is

fully open

ENVIRONMENT

• Donotdisposeofelectrictools,accessoriesand

packagingtogetherwithhouseholdwastematerial

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol @ will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product

described under “Technical data” is in conformity with the

following standards or standardization documents: EN

60335, EN 61000, EN 55014 in accordance with the

provisions of the directives 2006/95/EC, 2004/108/EC,

2006/42/EC, 2000/14/EC, 2011/65/EU

• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

¹ÊÁÂÆÎ¹Æ¼½ÊÇÇ¾¼½Æ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

Ä¹¾ÁÂÃ¿Ê¹¹¾

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

30.07.2013

NOISE/VIBRATION

• Measured in accordance with EN 60704-1 the sound

pressure level of this tool is 81dB(A) and the sound

power level 93 dB(A) (standard deviation: 3 dB), and the

vibration 2.5 m/s² (hand-arm method; uncertainty

K = 1.5 m/s²)

• Measured in accordance with 2000/14/EC the

guaranteed sound power level LWA is lower than 97

dB(A) (conformity assessment procedure according to

Annex V)

• The vibration emission level has been measured in

accordance with a standardised test given in EN/ISO

5349; it may be used to compare one tool with another

and as a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protectyourselfagainsttheeffectsofvibration

bymaintainingthetoolanditsaccessories,

keepingyourhandswarm,andorganizingyour

workpatterns

Содержание

Похожие устройства

MAINTENANCE SERVICE ENVIRONMENT This tool is not intended for professional use Before maintenance always switch off tool ensure there is no water pressure In tool and hand gun disconnect plug from power source and disconnect tool from water supply Always keep tool and cord clean especially ventilation slotsS do not use water solvents or polishes regularly clean spraying nozzle G using cleaning needle M remove spray lance K from hand gun L first Regularly check for worn or damaged components and have them repaired replaced when necessary Cleaning water filter rem we water filter E from inlet connector C with long nose pliers rinse it clean and put it back replace it when damaged I never use the tool with a damaged water filter Storage store the tool out of reach of children in a location where the ambient temperature will not exceed 40 C or drop below 0 C do not place other objects on top of the tool securely mount storage rail N on the wall with 4 screws not supplied and horizontally leveled use storage rail N and storage straps P as illustrated If the tool should fail despite the care taken in manufacturing and testing procedures repair should be carried out by an after sales service centre for SKIL power tools send the tool undismantled together with proof of purchase to your dealer or the nearest SKIL service station addresses as well as the service diagram of the tool are listed on www skil com Do not dispose of electric tools accessories and packaging together with household waste material only for EU countries in observance of European Directive 2002 96 EC on waste of electric and electronic equipment and its implementation in accordance with national law electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility symbol will remind you of this when the need for disposing occurs DECLARATION OF CONFORMITY C We declare under our sole responsibility that the product described under Technical data is in conformity with the following standards or standardization documents EN 60335 EN 61000 EN 55014 in accordance with the provisions of the directives 2006 95 EC 2004 108 EC 2006 42 EC 2000 14 EC 2011 65 EU Technical file at SKIL Europe BV PT SEU ENG1 4825 BD Breda NL Marijn van der Hoofden Operations Engineering Olaf Dijkgraaf Approval Manager SKIL Europe BV 4825 BD Breda NL 30 07 2013 C 10 NOISE VIBRATION Measured in accordance with EN 60704 1 the sound pressure level of this tool is 81dB A and the sound power level 93 dB A standard deviation 3dB and the vibration 2 5 m s2 hand arm method uncertainty K 1 5m s2 Measured in accordance with 2000 14 EC the guaranteed sound power level LWA is lower than 97 dB A conformity assessment procedure according to Annex V The vibration emission level has been measured in accordance with a standardised test given in EN ISO 5349 it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned using the tool for different applications or with different or poorly maintained accessories may significantly increase the exposure level the times when the tool is switched off or when it is running but not actually doing the job may significantly reduce the exposure level I protect yourself against the effects of vibration by maintaining the tool and Its accessories keeping your hands warm and organizing your work patterns TROUBLESHOOTING The following listing shows problem symptoms possible causes and corrective actions if these do not identify and correct the problem contact your dealer or service station I switch off the tool and disconnect the plug before Investigating the problem Spray is not consistent nozzle partly blocked clean nozzle Motor does not start or stops suddenly power supply socket faulty use another socket plug not connected connect plug thermal protection switched off the motor let the tool cool down for 5 minutes Motor is running but spray is poor nozzle completely blocked clean nozzle water filter clogged clean water filter air in the pump ensure that water inlet connector is securelyfitted inadequate water supply check that water tap is fully open 8

Скачать