Home
Главная
Zelmer
Утюги
Easy Control 28Z023
Инструкция по эксплуатации Страница: 62

Zelmer Easy Control 28Z023 [62/64] Burst of steam in vertical positio

62 GW28-016_v01

Burst of steam in vertical position – Always follow the garment

manufacturer’s ironing instructions mentioned at the garment label.

This function provides extra amount of steam to remove wrinkles on

delicate garments in hanging position, hanging curtains, or other hanging

fabrics.

Warning:

Do not apply steam on any clothes or fabrics that are being worn by

human or pets. Never direct the steam to human or pets.

Fill the water tank in as described under “How To Fill Water “. –

Connect the iron to a suitable mains supply outlet. See „Preparation –

for operation“.

The red and green – control light (6) glows for a moment and you can

hear single sound signal. Then the control lights (6) go off.

Turn the – temperature dial to ●●● position.

The red – control light (6) starts ashing indicating that the iron heater

is on and you can hear a single sound signal.

The red – control light (6) glows and you can hear the sound signal

when the required temperature is reached.

The iron is ready for use. –

Move the – steam control knob (5) to position.

Hold the iron between 15 and 30 –

centimetres away from the garment.

Press the – burst of steam button (10)

once – steam will shoot from the holes of

the soleplate.

For stubborn wrinkles, wait a few seconds –

before pressing the burst of steam

button (10) again. Most wrinkles can be

removed within three presses.

After operation move the – steam control

knob (5) to position.

After operation turn the – temperature dial

knob (7) in counter clockwise direction to „MIN” position. The iron is

switched off.

Disconnect the iron from mains supply outlet. –

When the iron gets cool completely, store it vertically in a safe place. –

It may be necessary to press the burst of steam button a few times

to start this function.

For optimum steam quality, do not operate the burst of steam (10)

more than three times after the control light goes off.

Self-cleaning

This function removes the scales and minerals built up in the steam

chamber. The iron will remain in the best condition if this function is

performed at least once a month or more regularly depending on the

hardness of the water used. Usually after more than 8 hours of operation

it is necessary to perform the sole plate (1) self-cleaning, then the green

control lamp (6) starts ashing.

Fill the water tank in as described under “How To Fill Water”. Fill it up –

to the half.

Place the iron on the surface in vertical, resting position. –

Connect the iron to a suitable mains supply outlet. See „Preparation –

for operation”.

The red and green – control light (6) glows for a moment and you can

hear single sound signal. Then the control lights (6) go off.

Turn the – temperature dial (7) in clockwise direction to ●●● position.

The red – control light (6) starts ashing indicating that the iron heater

is on and you can hear a single sound signal.

The red – control light (6) glows and you can hear the sound signal

when the required temperature is reached.

The iron is ready for use. –

Wait one cycle; the – control light (6) shall glow and go off.

Turn the – temperature dial knob (7) in counter clockwise direction to

„MIN” position. The iron is switched off.

Disconnect the iron from mains supply outlet. –

Hold the iron horizontally over a sink. –

Press and hold the – self-cleaning knob (2).

Steam and boiling hot water will drain from the holes on the soleplate –

washing away the scales and minerals that have built up inside the

steam chamber.

Gently move the iron back and forth until the water tank is empty. –

When self-cleaning is complete, release the – self-cleaning knob (2).

Rest your iron back on its heel rest and allow to fully cool down. –

Zelmer Easy Control 28Z023 [62/64] Burst of steam in vertical positio

Содержание

Похожие устройства