Home
Главная
Pioneer
Автомагнитола для смартфона
SPH-10BT
Инструкция по эксплуатации Страница: 2

Pioneer SPH-10BT [2/32] Connections

2En

Important

• When installing this unit in a vehicle

without an ACC (accessory) position on

the ignition switch, failure to connect the

red cable to the terminal that detects

operation of the ignition key may result

in battery drain.

• Use of this unit in conditions other than

the following could result in fire or

malfunction.

–Vehicles with a 12-volt battery and

neg

ative grounding.

–When speaker output is used by 4

chan

nels, use speakers over 50 W

(maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use

1 Ω to 3 Ω speakers for this unit.

–When rear speaker output is used by 2

of subwoofer, use speakers over 70 W

(maximum input power).

* Please refer to connections for a

nnection method.

• T

o prevent a short-circuit, overheating or

malfunction, be sure to follow the

directions below.

–Disconnect the negative terminal of the

bat

tery before installation.

–Secure the wiring with cable clamps or

hesive tape. Wrap adhesive tape

around wiring that comes into contact

with metal parts to protect the wiring.

– Place all cables away from moving parts,

ch as the shift lever and seat rails.

–Place all cables away from hot places,

such

as near the heater outlet.

–Do not connect the yellow cable to the

bat

tery by passing it through the hole

to the engine compartment.

–Cover any disconnected cable

nnectors with insulating tape.

–Do not shorten any cables.

–Never cut the insulation of the power

cable

of this unit in order to share the

power with other devices. The current

capacity of the cable is limited.

–Use a fuse of the rating prescribed.

–Never wire the negative speaker cable

rectly to ground.

–Never band together negative cables of

ultiple speakers.

• When t

his unit is on, control signals are

sent through the blue/white cable.

Connect this cable to the system remote

control of an external power amp or the

vehicle’s auto-antenna relay control

terminal (max. 300 mA 12 V DC). If the

vehicle is equipped with a glass antenna,

connect it to the antenna booster power

supply terminal.

• N

ever connect the blue/white cable to

the power terminal of an external power

amp. Also, never connect it to the power

terminal of the auto antenna. Doing so

may result in battery drain or a

malfunction.

• T

he black cable is ground. Ground cables

for this unit and other equipment

(especially, high-current products such as

power amps) must be wired separately. If

they are not, an accidental detachment

may result in a fire or malfunction.

• Th

e graphical symbol placed on

the product means direct current.

Connections/Installation

Connections

ACC position No ACC position

This unit

Power cord input

Microphone input

Microphone (3 m)

Rear output or subwoofer output

Front output

Antenna input

Parking sensor input

UART adaptor (supplied with parking

sen

sor unit (ND-PS1)) can be connected

(sold separately).

Fuse (10 A)

Wired remote input

Hard-wired remote control adapter can

be connec

ted (sold separately).

Power cord

To power cord input

Depending on the kind of vehicle, the

function of and may be different.

In this case, be sure to connect to

and to .

Yel low

Back-up (or accessory)

Yel low

Connect to the constant 12 V supply

rminal.

Red

Accessory (or back-up)

Red

Connect to terminal controlled by the

igni

tion switch (12 V DC).

Connect leads of the same colour to

each other.

Black (chassis ground)

Blue/white

The pin position of the ISO connector

ll differ depending on the type of

Pioneer SPH-10BT [2/32] Connections

Содержание

Похожие устройства