Beko CS 47100 Инструкция по эксплуатации онлайн [8/88] 4181

Содержание

d If the stove is placed below a wall kitchen cabinet the cabinet must be located at least 420 mm above the heating plate Minimal distance between the working area and the kitchen cabinet made of inflammable material is 700 mm e The wall that is in direct contact with the back side of the stove must have inflammable surface Connecting the appliance to the house gas distribution system Connection of the appliance to the house gas distribution system or liquefied gas bottle must be carried out in accordance with applicable regulations It s also necessary to make sure that the appliance has been adjusted for the relevant gas type If it has not been adjusted yet the procedure described in Adjusting for various gas types must be carried out Some models allow connecting the gas input on the left or the right side as needed if you want to change the connection change the hose holder position and move the gasket included If you use bottled liquefied gas install pressure regulator conforming to applicable safety regulations Important For safety reasons in order to properly use the internal gas energy and to improve appliance durability it is necessary to secure the required pressure at the appliance input as described in table 1 Nozzle and burner technical data Connecting gas hose Connection to the gas distribution network through a gas hose must be carried out in accordance with applicable safety regulations Internal diameter of the hose employed must be 8 mm for liquefied gas 13 mm for methane The following safety regulations must be observed when installing the hose no part of the hose can touch any place whose temperature exceeds 50 C hose length should not exceed 1500 mm the hose should not be twisted or pulled bent or crooked no objects with sharp edges or moving parts should touch the hose and it should not be subjected to any pressure every part of the hose should be accessible for inspection Make sure that both hose ends are firmly connected and fasten the hose with clamps as required by security regulations If any of the above recommendations is not feasible flexible metal pipes should be employed If the stove is to be installed according to the class 2 subclass 1 conditions we recommend using a flexible metal pipe for connection of the stove to the gas distribution in accordance with security regulations Threaded connection by a seamless stainless hose Remove the hose holder mounted on the appliance Appliance gas connection has an external thread G1 2 Only use material hoses sealing elements admissible according to currently applicable regulations The length of the flexible input must not exceed 2 000 mm Leak check Important After appliance installation check all connections for leakage with soapy water Never check leakage with a flame After connecting the appliance check whether the flexible hose does not touch moving parts anywhere and whether it s deformed or damaged Connecting the power cord to the mains A mains plug conforming to the load must be attached to the mains cord If the stove is attached to the mains directly a multi pole switch breaker 7 with contact distance of 3 mm when disengaged must be inserted between the appliance and the mains the switch must be appropriate for the appliance and it must conform to applicable safety standards grounding protection wire must not be interrupted by the switch Power cord must be placed so that it is never subjected to a temperature that would exceed the room temperature by 50 C or more Before carrying out the connection please check whether the building installation line protection can bear this appliance s load see the nameplate Whether the house electric distribution network features an effective grounding or zeroing protection system according to directives and legal regulations Whether the power plug or single pole switch are easily accessible at the installed appliance Note Never use adaptors switches or similar equipment because you could exceed maximum power load and maximum input A fire could start Adjusting the stove for various gas types If you use a different gas type than what the stove has been adjusted for see the nameplate the following steps must be carried out a Replace the installed hose holder with a holder included in the stove accessories Important Hose holder for liquefied gas is identified by No 8 methane hose holder is identified by No 13 Always use a new sealing ring b Replace burner nozzles on the heating plate Remove the grate and remove the burners from the plate Unscrew the nozzles with a 7 mm socket wrench and replace them with sockets appropriate for the given gas type that you will operate the appliance with see Table 1 Nozzle and burner technical data Put back all components on correct locations reversing the procedure