Tp-Link TL-R470T+ [113/118] Appendix b faq
![Tp-Link TL-R470T+ [113/118] Appendix b faq](/views2/1042345/page113/bg71.png)
-109-
Appendix B FAQ
Q1. What can I do if I cannot access the web-based configuration page?
1. For the first login, please try the following steps:
1) Make sure the cable is well connected to the LAN port of the Router. The corresponding LED
should flash or be solid light.
2) Make sure the IP address of your PC is set in the same subnet addresses of the Router. It’s
recommended to set your PC to get the IP address automatically. Then the Router with DHCP
enabled can automatically assign the IP address to your PC. If you want to configure your PC
manually, please set 192.168.0.x ("x" is any number between 2 to 254) for the IP address and
255.255.255.0 for the Subnet Mask.
3) Test the connection between your PC and TL-R470T+ via Ping command.
4) If you still cannot access the configuration page, please restore your Router to its factory
default settings and try to log in again.
2. If your management port has been changed, please log into the Router with the new address,
such as http://192.168.0.1:XX
(“XX” is the new management port number).
3. If you had successfully logged into the Router before, but now you cannot access the Router. It’s
quite possible that the configuration of your Router has been changed by others, especially when
the Remote Web Management function is enabled. You’re recommended to restore your Router
and reconfigure the management port number and the username as well as the password for your
network security.
4. If you cannot access the Router even after restoring the Router to its defaults, or your login is
dropped down just after a while, it’s quite possible that your Router is attacked by ARP cheating.
It’s recommended to locate and quarantine the source of ARP cheating so as to prevent your
network from the attacks.
5. Check to see if you have configured the proxy server for IE browser. If so, please disable the IE
proxy server first.
Q2: What can I do if I forgot the username and the password of the Router? How to restore the
Router to its factory default settings?
You can restore the Router to its factory default settings by the Reset button. It must be noted that
once the Router is reset, all the current configuration settings will be lost.
With the Router powered on, use a pin to press and hold the
Reset
button (about 5 seconds). If the SYS
LED is flashing 5 times in high frequency, release the
Reset
button. It means the Router is restored
successfully. The default management address of the Router is
http://192.168.0.1
, and the default
username and the password are both
admin
.
Содержание
- Ce mark warning 2
- Copyright trademarks 2
- Fcc statement 2
- Contents 3
- Package contents 5
- Chapter 1 about this guide 6
- Conventions 6
- Intended readers 6
- Overview of this guide 6
- Chapter 2 introduction 8
- Overview of the router 8
- Features 9
- Appearance 10
- Front panel 10
- Rear panel 10
- Chapter 3 quick installation guide 12
- Configure pc 12
- Chapter 4 configuration 22
- Status 22
- Network 23
- Quick setup 23
- Wan mode 23
- Dhcp client 43
- Dhcp reservation 43
- Mac address 45
- Statistics 46
- Switch 46
- Port mirror 47
- Rate control 49
- Port config 50
- Port status 51
- Port vlan 52
- User group 52
- Advanced 55
- Nat setup 55
- Virtual server 56
- Port triggering 58
- Traffic control 60
- Bandwidth control 62
- Session limit 64
- Configuration 65
- Load balance 65
- Session list 65
- Policy routing 66
- Link backup 67
- Protocol 69
- Routing 70
- Static route 70
- Anti arp spoofing 73
- Firewall 73
- Ip mac binding 73
- Arp scanning 74
- Arp list 75
- Attack defense 76
- Mac filtering 78
- Access control 79
- Url filtering 79
- Access rules 81
- Web filtering 81
- Service 83
- General 84
- Pppoe server 84
- Services 84
- Ip address pool 86
- Account 87
- Exceptional ip 89
- List of account 90
- E bulletin 91
- Dynamic dns 92
- Dyndns 93
- Peanuthull 96
- Comexe 97
- Admin setup 100
- Administrator 100
- Maintenance 100
- Login parameter 101
- Remote management 102
- Export and import 103
- Factory defaults 103
- Management 103
- Firmware upgrade 104
- Reboot 104
- Interface traffic statistics 105
- Statistics 105
- Diagnostics 106
- Ip traffic statistics 106
- Online detection 108
- Appendix a hardware specifications 112
- Appendix b faq 113
- Appendix c glossary 115
Похожие устройства
- Panasonic NV-VP33 Инструкция по эксплуатации
- Sony HDR-SR8E Инструкция по эксплуатации
- Sony SF-32NX/T1 ET4 Инструкция по эксплуатации
- Tp-Link TL-R480T+ Инструкция по эксплуатации
- Sony HDR-SR7E Инструкция по эксплуатации
- Sony MRW68ED1 Инструкция по эксплуатации
- Tp-Link TL-ER5120 Инструкция по эксплуатации
- Hotpoint-Ariston AQGD 149 S Инструкция по эксплуатации
- Sony HDR-SR5E Инструкция по эксплуатации
- Sony MRW62ES2171 Инструкция по эксплуатации
- Tp-Link TL-R402M Инструкция по эксплуатации
- Panasonic TC-14F1 Инструкция по эксплуатации
- Sony HDR-SR1E Инструкция по эксплуатации
- Sony ICD-PX312M 2Gb Инструкция по эксплуатации
- Tp-Link TL-R460 Инструкция по эксплуатации
- Panasonic KX-FP363RU Инструкция по эксплуатации
- Sony HDR-SR12E Инструкция по эксплуатации
- Sony ICD-UX512 2Gb Gold Инструкция по эксплуатации
- Tp-Link TL-R860 Инструкция по эксплуатации
- Toshiba GR-E261TR Инструкция по эксплуатации