![Fluke 4180 [12/30] Cautions](/img/pdf.png)
Fluke 4180 [12/30] Cautions
![Fluke 4180 [12/30] Cautions](/views2/1005265/page12/bgc.png)
4180, 4181 Precision Infrared Calibrator
Safety Information
6
Cautions1.4.2
Protect the target against dirt and damage – scrapes and scratches. A well kept target
surface, free from dirt and damage, produces better measurements. Use the target
cover whenever the instrument is not in use to protect the target. Always use the target
cover when transporting the instrument, but remember to never transport the instru-
ment when the target temperature is above 50°C.
DO NOT touch the target. Oils and salts from the skin will permanently damage the
target surface at high temperatures.
When ice forms on the target, change the instrument set-point higher than 50°C to
melt the excess ice. DO NOT wipe the front plate (target). Change the set-point to
100°C or higher to evaporate the excess water.
DO NOT use uids to clean the target surface.
DO NOT use shop air to clean the target surface. Oil and contaminants in the shop air
could contaminate the surface.
DO NOT use canned, compressed air (used to clean a computer) to clean the target
surface. Chemicals in the air could contaminate the target surface.
DO NOT force cool the surface. The surface should not be cooled by any method
other than natural convection. Forced air can often have oil or water in it. Even water
can leave mineral deposits on the surface. Trying to cool the surface too quickly can
also cause thermal shock to the emissive surface.
DO NOT use liquid nitrogen (LN2) to quick cool the target.
DO NOT plug the instrument into 230V if the fuse holder reads 115V. This action will
cause the fuses to blow and may damage the instrument.
Component lifetime can be shortened by continuous high temperature operation.
DO NOT change the values of the calibration constants from the factory set values.
Calibration constants shall only be changed by qualied and authorized personnel. The
correct setting of these parameters is important to the safety and proper operation of
the calibrator.
DO use a ground fault interrupt device.
Always operate this instrument at room temperatures as stated in Section 2.2 Environ-
mental Conditions on page 10.
The instrument is a precision instrument. Although is has been designed for optimum
durability and trouble free operation, it must be handled with care. It is important
to keep the calibration well and the IR target surface clean and clear of any foreign
matter.
Always carry the instrument in an upright position. The convenient pull-up handle al-
lows one hand carrying.
DO NOT operate the instrument in excessively wet, oily, dusty, or dirty environments.
DO NOT operate near ammable materials.
Содержание
- 4181 precision infrared calibrator 2
- Limited warranty limitation of liability 2
- Before you start 3
- Menu structure 9 3
- Quick start 11 3
- Specifications and environmental conditions 3
- Table of contents 3
- Maintenance 3 4
- Tables 5
- Figures 6
- Before you start 7
- Before you start 1 7
- Introduction 7
- Introduction 1 7
- Unpacking 7
- Unpacking 1 7
- 4181 precision infrared calibrator 8
- Ac alternating current 8
- Battery 8
- Complies with european union directives 8
- Documentation cd 8
- If all items are not present contact an authorized service center see section 1 authorized service centers on page 7 8
- Ir calibrator 8
- Power cord 8
- Report of calibration 8
- Serial cable 8
- Symbol description 8
- Symbols used 8
- Symbols used 1 8
- Symbols used table 1 8
- Table 1 lists the international electrical symbols some or all of these symbols may be used on the instrument or in this guide 8
- Table 1 symbols used 8
- Target cover 8
- User s guide 8
- Before you start 9
- Being used 9
- Caution identifies conditions and actions that may damage the instrument 9
- Safety information 9
- Safety information 1 9
- The following definitions apply to the terms warning and caution 9
- The portable ir calibrators are designed in accordance with iec 61010 1 iec 61010 2 010 and can csa 22 no 61010 04 use this instrument only as speci fied in this manual otherwise the protection provided by the instrument may be impaired 9
- Warning identifies conditions and actions that may pose hazards to the user 9
- Warnings 10
- Cautions 12
- Authorized service centers 13
- Ce comments 13
- Emc directive 13
- Emission testing 13
- Low voltage directive safety 13
- Specifications 15
- Specifications and environmental conditions 15
- Specifications and environmental conditions 2 15
- Table 2 specifications 15
- Environmental conditions 16
- Environmental conditions 2 16
- Display panel 17
- Parts and controls 17
- Parts and controls 3 17
- Quick start 17
- Quick start 3 17
- Setup 3 17
- Figure 1 display panel 18
- Display 19
- Back panel 20
- Figure 2 main screen 20
- Figure 3 418x back panel 21
- Figure 4 steps to language selection 22
- Ice buildup and purge procedure 4180 only 22
- Ice buildup and purge procedure 4180 only 3 22
- Icing warning 22
- Language selection 22
- Languages 22
- Languages 3 22
- Purge procedure 22
- Apparent temperature setting limits 23
- Emissivity setting of the ir thermometer 23
- Emissivity setting of the ir thermometer 3 23
- Removing ice buildup on the target 23
- 4181 precision infrared calibrator 24
- And the physical limits of the instrument the temperature range of the instrument may be limited from the specified range when using an emissivity setting other than 0 5 a table of this limitation is shown in table 3 24
- Apparent temperature limits table 3 24
- Forced air and convection 24
- Forced air and convection 3 24
- Since the 4180 and 4181 have a large surface area a major component of the tempera ture uncertainty is caused by changes in convection because of this the user should keep the instrument away from areas with large amounts of air flow or drafts 24
- Table 3 apparent temperature limits 24
- 4181 main menu 25
- F1 f1 f2 f3 f4 25
- Figure 5 temperature setup menu 25
- Hot keys 25
- Menu structure 25
- Temperature setup menu 25
- Temperature setup menu 4 25
- 4181 main menu 26
- 4181 precision infrared calibrator 26
- F1 f1 f2 f3 f4 26
- Figure 6 program menu 26
- Program menu 26
- Program menu 4 26
- Temp setup prog menu system menu view temp 26
- 4181 main menu 27
- F1 f1 f2 f3 f4 27
- Figure 7 system menu 27
- Menu structure 27
- System menu 27
- Temp setup prog menu system view temp 27
- 4181 main menu 28
- 4181 precision infrared calibrator 28
- F1 f1 f2 f3 f4 28
- Figure 8 view temp menu 28
- View temperature menu 28
- View temperature menu 4 28
- Maintenance 29
- Maintenance 5 29
Похожие устройства
- Belkin F8N383cw Black Инструкция по эксплуатации
- Denon DN-D4500 Инструкция по эксплуатации
- LG MS-2024J Инструкция по эксплуатации
- Bosch WAS 20443 OE Инструкция по эксплуатации
- Geo-Fennel FL 1000 585000 Инструкция по эксплуатации
- Supra SDD-3007 Инструкция по эксплуатации
- Fluke 421 Инструкция по эксплуатации
- Bosch WOR 20153 OE Инструкция по эксплуатации
- LG MS-2022GB Инструкция по эксплуатации
- Geo-Fennel FL 250 VA-N 241000 Инструкция по эксплуатации
- Supra SDD-3005 Инструкция по эксплуатации
- Belkin 8830ru06101 Инструкция по эксплуатации
- LG MS-2022G Инструкция по эксплуатации
- Fluke 434 Инструкция по эксплуатации
- Indesit WIUN 103 Инструкция по эксплуатации
- Sparky BN 502 Инструкция по эксплуатации
- Supra SDD-3004 Инструкция по эксплуатации
- Belkin F9H100venCW Инструкция по эксплуатации
- Fluke 435 Инструкция по эксплуатации
- Indesit WISL 102 Инструкция по эксплуатации