Home
Главная
Bort
УШМ (болгарка)
BWS-18Li-125
Инструкция по эксплуатации Страница: 11

Bort BWS-18Li-125 [11/40] Battery tool use and care

• Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may aect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account the

working conditions and the work to be performed. Use

of the power tool for operations dierent from those in-

tended could result in a hazardous situation.

Battery tool use and care

• Recharge only with the charger specied by the manu-

facturer. A charger that is suitable for one type of battery

pack may create a risk of re when used with another

battery pack.

• Use power tools only with specically designated bat-

tery packs. Use of any other battery packs may create a

risk of injury and re.

• When battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws

or other small metal objects, that can make a connec-

tion from one terminal to another. Shorting the battery

terminals together may cause burns or a re.

• Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

Service

Have your power tool serviced by a qualied repair person

using only identical replacement parts. This will ensure that

the safety of the power tool is maintained.

SAFETY WARNINGS FOR ANGLE GRINDER

• This power tool is intended to function as a grinder, sand-

er, wire brush or cut-o tool. Read all safety warnings, in-

structions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed be-

low may result in electric shock, re and/or serious injury.

• Operations such as polishing are not recommended to

be performed with this power tool. Operations for which

the power tool was not designed may create a hazard

and cause personal injury.

• Do not use accessories which are not specically de-

signed and recommended by the tool manufacturer. Just

because the accessory can be attached to your power

tool, it does not assure safe operation.

• The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Ac-

cessories running faster than their rated speed can break

and y apart.

• The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

guarded or controlled.

• Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

anges, the arbour hole of the accessory must t the

locating diameter of the ange. Accessories that do not

match the mounting hardware of the power tool will run

out of balance, vibrate excessively and may cause loss of

control.

• Do not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips and

cracks, backing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing an acces-

sory, position yourself and bystanders away from the

plane of the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged ac-

cessories will normally break apart during this test time.

• Wear personal protective equipment. Depending on ap-

plication, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors,

gloves and shop apron capable of stopping small abra-

sive or workpiece fragments. The eye protection must be

capable of stopping ying debris generated by various

operations. The dust mask or respirator must be capable

of ltrating particles generated by your operation. Pro-

longed exposure to high intensity noise may cause hear-

ing loss.

• Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may y away and cause injury beyond

immediate area of operation.

• Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

• Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning wheel.

• Never lay the power tool down until the accessory has

come to a complete stop. The spinning wheel may grab

the surface and pull the power tool out of your control.

• Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

• Do not operate the power tool near ammable materials.

Sparks could ignite these materials.

• Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution

or shock.

SAFETY WARNINGS FO BATTERY TOOL

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

Bort BWS-18Li-125 [11/40] Battery tool use and care

Содержание

Похожие устройства