Ryobi RBL26BP (3001815) [15/298] English original instructions
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ryobi RBL26BP (3001815) [15/298] English original instructions

Ryobi RBL26BP (3001815) [15/298] English original instructions
13
English (Original instructions)
■ Do not modify the product in any way or use parts
and accessories that are not recommended by the
manufacturer.
WARNING
If the product is dropped, suffers heavy impact, or
begins to vibrate abnormally, immediately stop the
engine and inspect for damage or identify the cause of
the vibration. Any damage should be properly repaired
or replaced by an authorised service centre.
■ Do not touch the area around the silencer or engine
of the product. These parts get hot during operation.
■ Stop the engine and allow the product to cool down
before refuelling.
■ For refuelling and fuel mixing, chose an area that is
well-ventilated, and is away from ignition sources,
such as sparks or flames, and flammable materials.
■ Do not smoke when mixing fuel or filling the fuel tank.
■ Mix and store fuel in a container approved for fuel.
■ Keep an appropriate type of fire extinguisher nearby
for dealing with fuel fires.
■ Remember to securely refit the fuel tank cap before
starting the engine. Check for fuel leaks.
■ Wipe up any fuel spillage. Move 9 m away from the
refuelling site before starting the engine.
■ To reduce the risk of injury associated with contacting
rotating parts, always stop the engine and disconnect
the spark plug boot. Make sure all moving parts have
come to a complete stop before:
● leaving the product unattended
● clearing blockages
● checking, cleaning, or working on the product
● inspecting the product after striking a foreign object
■ Immediately stop the engine in an event of accident
or breakdown. Do not operate the product again until
it has been fully checked by an authorised service
centre.
WARNING
Your blower is fi tted with a shoulder harness. Carefully
adjust the harness to comfortably help to support the
weight of the product and hang at your back with the
bower tube at your right-hand side.
WARNING
Identify the quick release mechanism and practice
using it before you start using the product. Its correct
use may prevent serious injury in the case of an
emergency. Never wear additional clothing over
the harness or otherwise restrict access to the quick
release mechanism.
BLOWER SAFETY WARNINGS
■ Wear a face filter mask in dusty conditions to reduce
the risk of injury associated with the inhalation of dust.
■ Slightly dampen surfaces in dusty conditions.
■ Do not use the product near open windows.
■ Use the full blower nozzle extension so that the air
stream can work close to the ground and perform
effectively.
■ Do not point the blower nozzle in the direction of
people or pets.
■ Never place objects inside the blower tubes.
■ Do not place the product on top of or near loose debris.
Debris can be sucked into the intake vent, resulting in
possible damage to the product.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use, and
the operator should pay special attention to avoid the
following:
■ Injury caused by vibration
– Always use the right tool for the job, use designated
handles and use the lowest speed necessary to
achieve the task.
■ Hearing injury caused by exposure to noise
– Wear ear protection and limit exposure.
■ Injury from flying objects from the blower tube airflow
– Wear eye protection at all times.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome.
Symptoms may include tingling, numbness, and blanching
of the fi ngers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking, and work practices are all thought to contribute to
the development of these symptoms. There are measures

Содержание

Похожие устройства

Скачать