Ryobi RBL26BP (3001815) [17/298] English original instructions
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ryobi RBL26BP (3001815) [17/298] English original instructions

Ryobi RBL26BP (3001815) [17/298] English original instructions
15
English (Original instructions)
FUEL CAP
WARNING
A leaking fuel cap is a fi re hazard and must be replaced
immediately.
The fuel cap contains a sealing gasket and a check
valve to allow air in. A clogged check valve will cause
poor engine performance. If performance improves when
the fuel cap is loosened, the check valve may be faulty.
Replace fuel cap if required.
When refi tting the fuel cap ensure it is not cross-threaded,
otherwise it will leak.
FUEL FILTER
The fuel supplied to the engine is passed through a fi lter
to remove any contaminants from entering the engine.
Contaminants in the fuel can cause poor performance and
damage to the engine.
The fuel fi lter is a non-serviceable item and, if needed,
should be replaced by an authorised service centre.
SPARK PLUG REPLACEMENT
See Fig. 7.
The product’s engine uses a Champion RCJ4 spark plug.
Use an exact replacement.
■ Remove the spark plug boot.
■ Loosen the spark plug by turning it counter-clockwise
with a socket.
■ Remove the spark plug.
■ Inspect the new spark plug. The spark plug must be
properly gapped and free of deposits in order to ensure
proper engine operation. The correct gap is 0.63 mm
(0.025 in.). To widen gap, if necessary, carefully bend
the ground (top) electrode. To lessen gap, gently tap
ground electrode on a hard surface.
■ Hand thread the new spark plug into the cylinder,
turning it clockwise.
■ Tighten with a socket. Torque to 24,40 Nm (216 lb.in.)
minimum, 29,82 Nm (264 lb.in.) maximum. Do not
over-tighten.
WARNING
Be careful not to cross-thread the spark plug. Cross-
threading will seriously damage the product.
TRANSPORTATION AND STORAGE
■ Stop the engine and allow it to cool down before
storing or transporting.
■ Clean all foreign materials from the product.
■ Drain all fuel from the tank into a container approved
for petrol. Remember to properly replace and tighten
the fuel cap.
■ Run the engine until it stops. This will remove all fuel
that could become stale and leave varnish and gum in
the fuel system.
■ If applicable, drain all lubricant from the engine into
a container approved for lubricant. Remember to
properly replace the lubricant cap.
■ Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children and well away
from sources of ignition.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■ Do not store outdoors.
■ When transporting the product in a vehicle, secure
it against movement or falling to prevent injury to
persons or damage to the product.
■ Never carry or transport the product while the engine
is running.
■ Abide all government and local regulations for the
safety storage and handling of petrol.
Short term storage (less than 1 month)
■ Stop the engine and allow the product to cool down
before storing or transporting.
■ Clean all foreign materials from the product.
■ Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children and well away
from sources of ignition.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■ Do not store outdoors.
SYMBOLS
Some of the following symbols may be used on this
tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate
the tool better and safer.
Precautions that involve your safety.
To reduce the risk of injury, you must
read and understand the operator’s
manual before using the product.

Содержание

Похожие устройства

Скачать