Home
Главная
Defort
Сварочный Аппарат
DWP-1000
Инструкция по эксплуатации Страница: 8

Defort DWP-1000 [8/20] C personal safety

tric shock. If the power tool comes with an earthed

wire, the plug may only be connected to an earthed

receptacle. At work sites, in damp surroundings, in

the open or in the case of comparable types of use,

only operate the power tool off the mains using a 30

mA fault current protected switch (FI breaker).

b) Avoid body contact with earthed or grounded sur-

faces such as pipes, radiators, ranges and refrigera-

tors. There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for carry-

ing, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

C) Personal safety

This appliance is not intended for use by persons (in-

cluding children) with reduced physical, sensory or men-

tal capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsi-

ble for their safety.

Children should be supervised to ensure that they do

not play with the appliance.

a) Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use

a power tool while you are tired or under the inﬂ u-

ence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in

serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non skid safe-

ty shoes, hard hat, or hearing protection used for ap-

propriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the

off position before plugging in. Carrying power tools

with your ﬁ nger on the switch or plugging in power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in per-

sonal injury.

e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of these devices

can reduce dust related hazards.

h) Only allow trained personnel to use the power tool.

Apprentices may only operate the power tool when

they are over 16, when this is necessary for their

training and when they are supervised by a trained

operative.

D) Power tool use and care

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be control-

led with the switch is dangerous and must be re-

paired.

c) Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing power tools. Such preventive safety meas-

ures reduce the risk of starting the power tool ac-

cidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools oper-

ation. If damaged, have the power tool repaired by a

qualiﬁ ed expert or by an authorised after-sales serv-

ice facility before use. Many accidents are caused

by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Secure the workpiece. Use clamps or a vice to hold

the workpiece. This is safer than holding it with your

hand, and also it frees both hands to operate the

equipment.

h) Use the power tool, accessories and tool bits etc., in

accordance with these instructions and in the man-

ner intended for the particular type of power tool,

taking into account the working conditions and the

work to be performed. Use of the power tool for op-

erations different from those intended could result in

a hazardous situation. All unauthorised modiﬁ cations

to the power tool are prohibited for safety reasons.

E) Service

a) Have your power tool serviced by a qualiﬁ ed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is main-

tained.

b) Comply with maintenance instructions and instruc-

tions on tool replacements.

c) Check mains lead of power tool regularly and have

it replaced by a qualiﬁ ed expert or an authorised

after-sales service facility in case of damage. Check

extension cable regularly and replace it when dam-

aged.

Defort DWP-1000 [8/20] C personal safety

Содержание

Похожие устройства