Indesit WITXL 1251 [11/84] Troubleshooting
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Indesit WITXL 1251 [11/84] Troubleshooting

Indesit WITXL 1251 [11/84] Troubleshooting
11
GB
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem can’t easily
be solved by consulting the following list.
Troubleshooting
Problem
The washing machine won’t start.
The wash cycle won’t start.
The washing machine fails to load
water.
The washing machine continuou-
sly loads and unloads water.
The washing machine does not
drain or spin.
The washing machine vibrates too
much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same time
as at least one other LED.
There is too much foam.
Possible causes/Solution:
• The appliance is not plugged into the socket, or not enough to
make contact.
• There has been a power failure.
• The appliance door is not shut properly. The Lid locked Led flashes.
• The button has not been pressed.
• The START/RESET button has not been pressed.
• The water tap is not turned on.
• A delayed start has been set (using the Delay Timer, see page 9).
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
• The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
• The free end of the hose is underwater (see page 3).
• The wall drainage system doesn’t have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and call for Assistance. If the dwelling is on one of the upper floors of
a building, there may be drain trap problems causing the washing machine to load
and unload water continuously. In order to avoid such an inconvenience, special
anti-drain trap valves are available in shops.
• The programme does not foresee the draining: some programmes
require enabling the draining manually.
• The Easy iron option is enabled: to complete the programme, press
the START/RESET button.
• The drain hose is bent (see page 3).
• The drain duct is clogged.
• The drum was not unblocked correctly during installation (see page 2).
• The washing machine is not level (see page 2).
• The washing machine is closed in between furniture cabinets and
the wall (see page 2).
• The water inlet hose is not screwed on correctly (see page 2).
• The detergent dispenser is obstructed (to clean it, see page 4).
• The drain hose is not secured properly (see page 3).
• Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
• The detergent is not suitable for machine washing (it should bear
the definition “for washing machines” or “hand and machine wash”,or the like).
• You used too much detergent.

Содержание

Похожие устройства

Troubleshooting T moesiT Your washing machine could fail to work Before calling for Assistance see page 12 make sure the problem can t easily be solved by consulting the following list Problem Possible causes Solution The washing machine won t start The appliance is not plugged into the socket or not enough to make contact There has been a power failure The wash cycle won t start The appliance door is not shut properly The Lid locked Led flashes The CD button has not been pressed The START RESET button has not been pressed The water tap is not turned on A delayed start has been set using the Delay Timer see page 9 The washing machine fails to load water The water inlet hose is not connected to the tap The hose is bent The water tap is not turned on There is a water shortage The water pressure is insufficient The START RESET button has not been pressed The washing machine continuou The drain hose is not fitted between 65 and 100 cm from the floor see page 3 The free end of the hose is underwater see page 3 The wall drainage system doesn t have a breather pipe sly loads and unloads water If the problem persists even after these checks turn off the water tap switch the appliance off and call for Assistance If the dwelling is on one of the upper floors of a building there may be drain trap problems causing the washing machine to load and unload water continuously In order to avoid such an inconvenience special anti drain trap valves are available in shops The washing machine does not drain or spin The programme does not foresee the draining some programmes require enabling the draining manually The Easy iron option is enabled to complete the programme press the START RESET button The drain hose is bent see page 3 The drain duct is clogged The washing machine vibrates too much during the spin cycle The drum was not unblocked correctly during installation see page 2 The washing machine is not level see page 2 The washing machine is closed in between furniture cabinets and the wall see page 2 The washing machine leaks The water inlet hose is not screwed on correctly see page 2 The detergent dispenser is obstructed to clean it see page 4 The drain hose is not secured properly see page 3 The ON OFF DOOR LOCK Led flashes rapidly at the same time as at least one other LED Switch off the machine and unplug the appliance wait for approximately 1 minute then switch it on again If the problem persists contact Assistance There is too much foam The detergent is not suitable for machine washing it should bear the definition for washing machines or hand and machine wash or the like You used too much detergent 11

Скачать