Ariston CISPF 640 E Инструкция по эксплуатации онлайн [4/24] 65921
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ariston CISPF 640 E Инструкция по эксплуатации онлайн [4/24] 65921

Ariston CISPF 640 E Инструкция по эксплуатации онлайн [4/24] 65921
GB
4
There is an adjustable
LL
LL
L-shaped pipe fitting on the
appliance supply ramp and this is fitted with a seal in
order to prevent leaks. The seal must always be replaced
after rotating the pipe fitting (seal provided with
appliance). The gas supply pipe fitting is a threaded 1/2
gas cylindrical male attachment.
Connecting a flexible jointless stainless steel pipe to a
threaded attachment
The gas supply pipe fitting is a threaded 1/2 gas
cylindrical male attachment.
These pipes must be installed so that they are never longer
than 2000 mm when fully extended. Once connection has
been carried out, make sure that the flexible metal pipe
does not touch any moving parts and is not compressed.
! Only use pipes and seals that comply with current
national regulations.
Checking the tightness of the connection
! When the installation process is complete, check the
pipe fittings for leaks using a soapy solution. Never use a
flame.
Adapting to different types of gas
To adapt the hob to a different type of gas other than
default type (indicated on the rating plate at the base of
the hob or on the packaging), the burner nozzles should
be replaced as follows:
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a 7 mm socket spanner, and
replace them with nozzles for the new type of gas (see
table 1 “Burner and nozzle characteristics”).
3. Reassemble the parts following the above procedure in
the reverse order.
4. Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.
• Adjusting the burners’ primary air :
Does not require adjusting.
• Setting the burners to minimum:
1. Turn the tap to the low flame position.
2. Remove the knob and adjust the adjustment screw,
which is positioned in or next to the tap pin, until the
flame is small but steady.
3. Having adjusted the flame to the required low setting,
while the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out.
4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are set
to the low flame setting, increase this low flame setting
using the adjusting screw.
5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax or a similar
substance.
! If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.
! Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet pipe (in order
to comply with current national regulations).
DATA PLATE
Electrical
connections
See data plate
This appliance conforms to the
following European Economic
Community directives:
-2006/95/EEC dated 12/12/06
(Low Voltage) and subsequent
amendments
- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility)
and subsequent amendments
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2009/142/EEC dated 30/11/09
(Gas) and subsequent
amendments.
- 2002/96/EC and subsequent
amendments.

Содержание

Похожие устройства

GB There is an adjustable L shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks The seal must always be replaced after rotating the pipe fitting seal provided with appliance The gas supply pipe fitting is a threaded 1 2 gas cylindrical male attachment to the low flame setting increase this low flame setting using the adjusting screw Connecting a flexible jointless stainless steel pipe to a threaded attachment The gas supply pipe fitting is a threaded 1 2 gas cylindrical male attachment These pipes must be installed so that they are never longer than 2000 mm when fully extended Once connection has been carried out make sure that the flexible metal pipe does not touch any moving parts and is not compressed Only use pipes and seals that comply with current national regulations Checking the tightness of the connection When the installation process is complete check the pipe fittings for leaks using a soapy solution Never use a flame Adapting to different types of gas To adapt the hob to a different type of gas other than default type Indicated on the rating plate at the base of the hob or on the packaging the burner nozzles should be replaced as follows 5 Once the adjustment has been made replace the seals on the by passes using sealing wax or a similar substance If the appliance is connected to liquid gas the regulation screw must be fastened as tightly as possible Once this procedure is finished replace the old rating sticker with one indicating the new type of gas used Stickers are available from any of our Service Centres Should the gas pressure used be different or vary slightly from the recommended pressure a suitable pressure regulator must be fitted to the Inlet pipe in order to comply with current national regulations AIO 77 1 Remove the hob grids and slide the burners off their seats 2 Unscrew the nozzles using a 7 mm socket spanner and replace them with nozzles for the new type of gas see table 1 Burner and nozzle characteristics 3 Reassemble the parts following the above procedure in the reverse order 4 Once this procedure is finished replace the old rating sticker with one indicating the new type of gas used Sticker are available from any of our Service Centres Adjusting the burners primary air DATA PLATE Electrical connections This appliance conforms to the following European Economic Does not require adjusting Setting the burners to minimum 1 Turn the tap to the low flame position 2 Remove the knob and adjust the adjustment screw which is positioned in or next to the tap pin until the flame is small but steady 3 Having adjusted the flame to the required low setting while the burner is alight quickly change the position of the knob from minimum to maximum and vice versa several times checking that the flame does not go out 4 Some appliances have a safety device thermocouple fitted If the device fails to work when the burners are set 4 See data plate ΠCommunity directives 2006 95 EEC dated 12 12 06 Low Voltage and subsequent amendments 2004 108 EEC dated 15 12 04 Electromagnetic Compatibility and subsequent amendments 93 68 EEC dated 22 07 93 and subsequent amendments 2009 142 EEC dated 30 11 09 Gas and subsequent amendments 2002 96 EC and subsequent amendments

Скачать