Planet ISW-800M [55/57] Troubleshooting
5. TROUBLESHOOTING
This section is intended to help you solve the most common problems on the industrial Ethernet switch.
5.1 Incorrect connections
The switch port can auto detect straight or crossover cable when you link switch with other Ethernet
device. For the RJ-45 connector should use correct UTP or STP cable, 10/100Mbps port use 2-pairs
twisted cable. If the RJ-45 connector is not correct pin on right position then the link will fail. For fiber
connection, please notice that fiber cable mode and fiber module should be match.
5.1.1 Faulty or loose cables
Look for loose or obviously faulty connections. If they appear to be OK, make sure the connections are
snug. IF that does not correct the problem, try a different cable.
5.1.2 Non-standard cables
Non-standard and miss-wired cables may cause numerous network collisions and other network problem,
and can seriously impair network performance. A category 5-cable tester is a recommended tool for
every 100Base-T network installation.
5.1.3 Improper Network Topologies
It is important to make sure that you have a valid network topology. Common topology faults include
excessive cable length and too many repeaters (hubs) between end nodes. In addition, you should make
sure that your network topology contains no data path loops. Between any two ends nodes, there should
be only one active cabling path at any time. Data path loops will cause broadcast storms that will severely
impact your network performance.
5.1.4 Incorrect Power Input
Verify that you are using the right power cord/adapter (DC 12-48V), please don't use the power adapter
with DC output bigger than 48V, or it will burn this converter down.
5.2 Diagnosing LED Indicators
The Switch can be easily monitored through panel indicators to assist in identifying problems, which
describes common problems you may encounter and where you can find possible solutions.
Содержание
- Isw 800m 1
- Port managed industrial ethernet switch 1
- User s manual 1
- Ce mark warning 2
- Disclaimer 2
- Fcc warning 2
- Revision 2
- Trademarks 2
- Weee warning 2
- Table of contents 3
- How to use this manual 5
- Introduction 5
- Packet contents 5
- Product feature 5
- Product specification 6
- Back plane 7
- Both of port based and tag based vlan group up to 64 vlans 7
- Dimension w x d x h 7
- Emission 7
- Installation 7
- Mac address 7
- Management 7
- Management interface 7
- Memory buffer 7
- Network cable 7
- Operating environment 7
- Packet throughput ability 7
- Power consumption 7
- Power supply 7
- Stability testing 7
- Storage environment 7
- Switching 7
- Vlan supports port based vlan and ieee802 q tag vlan 7
- Hardware installation 9
- Product description 9
- Product overview 9
- Switch front panel 9
- Led indications 10
- Dip switches 11
- Reset button 11
- Status 11
- Switch bottom panel 12
- Wiring the power inputs 12
- Wiring the fault alarm contact 13
- Din rail mounting 14
- Fault alarm contact 14
- Mounting installation 14
- V dc buzzer 24v battery 14
- Wall mount plate mounting 15
- Hardware installation 17
- Industrial switch 17
- Industrial switch function application the following figure is a sample application of the 17
- Network application 17
- Network installation 17
- This chapter provides some sample applications to help user to have more actual idea of 17
- Redundant ring application 18
- Coulping ring application 19
- Dual homing application 20
- About web based management 21
- Preparing for web management 21
- System login 21
- Web management 21
- Port status 22
- Port statistics 23
- Single port information 23
- Port control 24
- Switch settings 25
- Port mirroring 26
- Vlan configuration 27
- Port based vlan 28
- Q vlan 29
- E mail alert configuration 32
- Port vi 32
- Event configuration 33
- Power alarm configuration 34
- Ip configuration 35
- Sntp configuration 36
- Ip security 38
- Rstp configuration 39
- System configuration 39
- Per port configuration 40
- Redundant ring 41
- Qos configuration 43
- Community string 45
- Snmp configuration 45
- System operations 45
- Security manager 46
- Trap manager 46
- Configuration backup 47
- Tftp restore configuration 47
- Tftp backup configuration 48
- Factory default 49
- Tftp update firmware 49
- Save configuration 50
- Rate control 51
- System reboot 51
- System log 52
- System log configuration 52
- Event configuration 53
- Diagnosing led indicators 55
- Faulty or loose cables 55
- Improper network topologies 55
- Incorrect connections 55
- Incorrect power input 55
- Non standard cables 55
- Troubleshooting 55
- Cabling 56
- Appendix 57
- Base tx 10base t pin assignments 57
Похожие устройства
- Xerox WorkCentre 6015B Инструкция по эксплуатации
- Elna 3230 Инструкция по эксплуатации
- Planet ISW-802M Инструкция по эксплуатации
- Elna 5200 Инструкция по эксплуатации
- Xerox WorkCentre 6015N Инструкция по эксплуатации
- Planet IGS-801 Инструкция по эксплуатации
- Elna 5300 Инструкция по эксплуатации
- Planet IGS-801T Инструкция по эксплуатации
- Xerox WorkCentre 6015NI Инструкция по эксплуатации
- Elna 6200 Инструкция по эксплуатации
- Planet ISW-500 Инструкция по эксплуатации
- Xerox 7600i Инструкция по эксплуатации
- Elna 7300 - PRO QUILTING QUEEN Инструкция по эксплуатации
- Planet ISW-501T Инструкция по эксплуатации
- Elna EXCELLENCE 740 Инструкция по эксплуатации
- Planet ISW-511S15 Инструкция по эксплуатации
- HP CB317HE 301 (№178) Инструкция по эксплуатации
- Elna LOTUS Инструкция по эксплуатации
- Planet ISW-621 Инструкция по эксплуатации
- HP CB318HE 301 (№178) Инструкция по эксплуатации