Home
Главная
Bort
Фены
BHG-2000L-K
Инструкция по эксплуатации Страница: 3

Bort BHG-2000L-K [3/44] Installation

Hot air gun

CAREFULLY READ THE INSTRUCTIONS BEFORE

YOU USE THE HOT AIR GUN!

1. ADDITIONAL SAFETY RULES

BEFORE USING THE APPLIANCE:

1. Check the following:

- Make sure the voltage of the hot air gun corresponds

with the power voltage.

- Are the mains lead and the mains plug in a good

state: strong, without ravels or damages.

2. Avoid the use of long extension cables.

3. Do not use the appliance under moist circumstanc-

es.

4. The metal mouthpiece gets hot. Watch out and do

not touch the metal mouthpiece.

5. Prevent damage of the heating element. Do not lock

or block the mouthpiece.

6. Do not leave the appliance when switched on.

7. When the appliance is not in use, it can be put away

on the collapsible support, which is on the air gun.

By collapsing this support, the air gun can easy be

put away on it. The hot air gun now stands on the

support with the mouthpiece up.

8. Do not use the appliance for drying hair or for drying

living human beings in general.

9. Do not use the appliance in a bath, above water or in

spaces where easy inﬂ ammable liquids are used.

Warning! This appliance operates at a temperature

of 200-600 degrees without visible signs of this

temperature (no ﬂ ames); still there is a chance of

ﬁ re risk. Watch out for the hot air stream from the

mouthpiece. This air stream can cause burns.

WHEN OPERATING THE APPLIANCE:

1. If you are going to use the hot air gun, vapours and

gas can be liberated during a short time. This can be

harmful for your health. Asthmatics can suffer hin-

drance of it.

2. Before connecting the plug to the mains voltage you

have to check if the switch is in position “0”.

3. Keep the mains lead always away from the mouth-

piece of the hot air gun.

4. Keep children and animals away from the appliance

if you are using it.

IMMEDIATELY SWITCH OFF THE APPLIANCE

WHEN:

1. plug and/or cable are defective or damaged;

2. the switch is defective;

3. you smell or see smoke caused by scorched insula-

tion from the hot air gun.

2. INSTALLATION

You can work manually with this hot air gun or you can

put it in a vertical position. If you use the vertical posi-

tion the metal suspension bracket of the handgrip must

also stand vertical for supporting the handgrip on the

correct place.

3. USING THE APPLIANCE

THE HOT AIR GUN CAN BE USED FOR:

• plumbing work like tube connections, solder, bowing

tubes;

• removing paint, varnish and lacquer without ﬁ re-

risk;

• quickly drying of appliances which have become

wet;

• drying surfaces for quick repairing;

• removing self-adhesive labels in a clean way;

• placing PVC labels;

• blistering after sticking PVC materials can be

smoothed after heating;

• easy removing of vinyl carpeting;

• forming all synthetics with a low temperature among

which polyethylene and PVC;

• forming all synthetics with a high temperature among

which acryl and plexiglass;

• smelting synthetics, among which matters and foils

with PVC layer;

• applying heat shrinking tubes;

• shrink wrappers;

• thawing tubes and engines;

• repairing ﬁ nishing layers: email of bath and house-

hold appliances;

• applying epoxy powder cover layers;

• repairing of ski's, surf-boards and other sports

goods;

• unscrewing too fast ﬁ xed screws and connections.

4. BEFORE OPERATING

Before you switch on the hot air gun you have to search

for the right adapter for the mouthpiece and assemble it

on the mouthpiece if it is still cold.

IMPORTANT: Replace the mouthpiece only:

• with a stationary engine;

• when the appliance is disconnected;

• when the mouthpiece is cold.

5. OPERATION

• Check if the mains switch is on position “0” before

you connect the apparatus;

• Keep the power voltage always away from the hot

air stream and the mouthpiece.

Tip: If you want to get the best result, test all appli-

ances on a little part of the workpiece.

Bort BHG-2000L-K [3/44] Installation

Содержание

Похожие устройства