Metabo SE 12-115 [14/96] Troubleshooting

Metabo SE 12-115 [14/96] Troubleshooting
ENGLISHen
14
frequently and thoroughly. Here, the machine must
be held firmly.
Mains powered machines: The Autostop carbon
brushes must only be replaced in a specialist work-
shop. Always have checks and maintenance work
carried out by Metabo Customer Service.
10.1 Mains powered machines
- Electronic restart protection
The red electronic signal indicator (2) starts
flashing. If the mains plug is inserted with the
machine switched on, or if the current supply is
restored following an interruption, the machine
does not start up. Switch the machine off and then
back on again.
- The electronic signal indicator (2) lights up
and on-load speed is reduced.
Winding temperature too high. Run the machine in
idling until the electronics signal indicator
switches off.
- High-energy, high-frequency interference
High-energy, high-frequency interference can
cause the machine to deactivate. In this case,
please switch off the machine, disconnect the
plug and then reinsert. As soon as the interference
is reduced, you can continue work.
10.2 Cordless machines
- The electronic signal display (2) lights up and
the load speed decreases. The temperature is
too high! Run the machine in idling until the elec-
tronics signal indicator switches off.
- The electronic signal display (2) flashes and
the machine does not start. The restart protec-
tion is active. The machine will not start if the
battery pack is inserted while the machine is on.
Switch the machine off and on again.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Special instructions for cordless machines:
Battery packs must not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).
Explanation of details on page 3. Subject to
changes serving technical progress.
D =Permitted wheel diameter
B
max
=Maximum wheel width
M=Spindle thread
l=Length of spindle
n =No-load speed (maximum speed)
U =Voltage of battery pack
P
1
=Nominal power input
P
2
=Power output
m =Weight with smallest battery pack/weight
without cord
Measured values determined in conformity with
EN 60745.
Direct current (cordless machines)
~ Alternating current (mains powered machines)
Machine in protection class II (mains powered
machines)
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending on
the particular application and the condition of the
tool or power tool. In estimating the values, you
should also include work breaks and periods of low
use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.
Vibration total value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h, P
=Vibration emission value (polishing)
K
h,P
=Uncertainty (vibration)
10. Troubleshooting
11. Accessories
12. Repairs
13. Environmental Protection
14. Technical specifications

Содержание

Скачать
Случайные обсуждения