Flex SE 14-2 150 Set [16/240] Safety instructions a
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Flex SE 14-2 150 Set [16/240] Safety instructions a

Flex SE 14-2 150 Set [16/240] Safety instructions a
SE 14-2 125/SE 14-2 150
16
Safety instructions
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=
c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~ åÇLçê=ë Éêáçìë=áåàìêáÉ ë
K=
hÉÉé=~ää=ë ~ÑÉ íó =áå ëíê ìÅ íá çå ë=~ åÇ=çíÜ Éê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
This electric power tool must be used
as a grinder, sander and polisher.
Read all safety warnings, instructions,
illustrations and specifications provided
with this power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/
or serious injury.
Operations such as wire brushing
or cutting-off are not recommended
to be performed with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause
personal injury.
Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the accessory can be attached
to your power tool, it does not assure safe
operation.
The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories running faster than their rated
speed can break and fly apart.
The outside diameter and the thickness
of your accessory must be within
the capacity rating of your power tool.
Incorrectly measured insertion tools cannot
be adequately shielded or controlled.
Sanding discs, sanding pads or other
accessories must fit exactly on the grin-
ding spindle of your electric power tool.
Insertion tools, which do not fit exactly on the
grinding spindle of the electric power tool,
rotate unevenly, vibrate violently and may
result in loss of control.
Do not use a damaged accessory.
Before use, always check insertion tools
for splinters and cracks, sanding pad
for cracks, wear and severe abrasion.
If power tool or accessory is dropped,
inspect for damage or install an un-
damaged accessory.
After inspecting and installing an acces-
sory, position yourself and bystanders
away from the plane of the rotating
accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break
apart during this test time.
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
If appropriate, wear a dust mask, hearing
protection, protective gloves and/
or a special apron which protect you from
small sanding and material particles.
The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator must
be capable of filtrating particles generated
by your operation. Prolonged exposure
to high intensity noise may cause hearing loss.
Keep bystanders a safe distance away
from work area. Anyone entering the work
area must wear personal protective
equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
Hold power tool by insulated gripping
surfaces only, when performing an opera-
tion where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire
may make exposed metal parts of the power
tool "live" and shock the operator.
Position the cord clear of the spinning
accessory.
If you lose control, the cord may be cut
or snagged and your hand or arm may
be pulled into the spinning accessory.
Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
Do not run the power tool while carrying
it at your side.
Accidental contact with the spinning
accessory could snag your clothing,
pulling the accessory into your body.

Содержание

Похожие устройства

en Safety instructions A WARNING Read all safety instructions and other instructions Failure to observe the safety instructions and other instructions may result in an electric shock fire and or serious injuries Keep all safety instructions and other instructions in a safe place for the future This electric power tool must be used as a grinder sander and polisher Read all safety warnings instructions illustrations and specifications provided with this power tool Failure to follow all instructions listed below may result in electric shock fire and or serious injury Operations such as wire brushing or cutting off are not recommended to be performed with this power tool Operations for which the power tool was not designed may create a hazard and cause personal injury Do not use accessories which are not specifically designed and recommended by the tool manufacturer Just because the accessory can be attached to your power tool it does not assure safe operation The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool Accessories running faster than their rated speed can break and fly apart The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool Incorrectly measured insertion tools cannot be adequately shielded or controlled Sanding discs sanding pads or other accessories must fit exactly on the grin ding spindle of your electric power tool Insertion tools which do not fit exactly on the grinding spindle of the electric power tod rotate unevenly vibrate violently and may result in loss of control Do not use a damaged accessory Before use always check insertion tools for splinters and cracks sanding pad for cracks wear and severe abrasion 16 SE 14 2 125 SE 14 2 150 If power tool or accessory is dropped inspect for damage or install an un damaged accessory After inspecting and installing an acces sory position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one minute Damaged accessories will normally break apart during this test time Wear personal protective equipment Depending on application use face shield safety goggles or safety glasses If appropriate wear a dust mask hearing protection protective gloves and or a special apron which protect you from small sanding and material particles The eye protection must be capable of stopping flying debris generated by various operations The dust mask or respirator must be capable of filtrating particles generated by your operation Prolonged exposure to high intensity noise may cause hearing loss Keep bystanders a safe distance away from work area Anyone entering the work area must wear personal protective equipment Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation Hold power tool by insulated gripping surfaces only when performing an opera tion where the cutting accessory may contact hidden wiring or its own cord Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and shock the operator Position the cord clear of the spinning accessory If you lose control the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory Never lay the power tool down until the accessory has come to a complete stop The spinning accessory may grab the surface and pull the power tool out of your control Do not run the power tool while carrying it at your side Accidental contact with the spinning accessory could snag your clothing pulling the accessory into your body

Скачать