Einhell BT-SM 2131 Dual [21/148] Functions
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Einhell BT-SM 2131 Dual [21/148] Functions

Einhell BT-SM 2131 Dual [21/148] Functions
or right of the fixed saw table (18).
Undo the locking screws for the workpiece
support (26).
Mount the workpiece support (10) on the fixed
saw table (18) and tighten the appropriate locking
screw (26) (Figure 4).
Mount the second workpiece support (10) on the
opposite side of the saw and secure with the
appropriate locking screw (26).
When the locking screw (21) is loosened, you can
tilt the machine head (4) to the left by up to 45°.
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so that
the saw stands in a horizontal and firm position.
Screw the additional feet (9) to the feet of the
fixed saw table (18).
Then swing out the stability bar (36) to the rear
until it engages.
6.3 Precision adjustment of the stop for crosscut
90° (Fig. 7-8)
Fasten the turntable (17) in 0° position.
Undo the locking screw (21) and move the
machine head (4) all the way to the right using the
handle (1).
Place the 90° angular stop (a) between the blade
(7) and the turntable (17).
Adjust the adjustment screw (29) until the angle
between the blade (7) and the turntable (17)
equals 90°.
Finally check the position of the pointer (20) on
the scale (19). If necessary, undo the pointer (20)
with a Philips screwdriver, set it to the 0° position
on the scale (19) and retighten the retainer screw.
No stop angle included.
6.4 Precision adjustment of the stop for miter cut
45° (Fig. 1, 6, 7, 9)
Fasten the turntable (17) in 0° position.
Undo the locking screw (21) and move the
machine head (4) all the way to the left using the
handle (1), until it coincides at 45°.
Place the 45° stop angle (b) between the blade
(7) and the turntable (17).
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
No stop angle included.
6.5 Adjusting the miter angle on the machine
head (Fig. 2, 12-13)
Undo the locking screw (21).
Hold the machine head (4) by the handle (1).
After pulling the button (33), the machine head
can be tipped infinitely as well as to several
locking points.
Angles to the left: 0-45°
Angles to the right: 0-45°
Re-tighten the locking screw (21).
6.6 Adjusting the movable stop rails
(Fig. 1, 10-14)
Important. This saw is equipped with movable
stop rails (34) that are screwed to the fixed stop
rail (11).
For carrying out angle and miter cuts the movable
stop rails must be adjusted to prevent a collision
with the saw blade.
For miter and angle cuts to the left, the left stop
rail must be moved outwards. For angle cuts to
the right, the right stop rail must be moved
outwards. Undo the locking screws on the
movable stop rails and pull the rails back so far
that a collision with the saw blade can be ruled
out. Prior to every cut retighten the locking screws
of the stop rails.
For miter cuts and double miter cuts with the saw
head tilted to the right, the right stop rail must be
removed completely. Important! In this case the
maximum permissible workpiece height is
reduced (see 5. Technical data).
Always fasten the movable stop rails back to the
equipment again after you have completed your
work.
The stop rails must always remain together with
the equipment. A removed stop rail will impair the
operational safety of the equipment.
7. Functions
7.1 Cross cut 90° and turntable 0° (Fig. 1-3, 11)
For cutting widths up to approx. 100 mm it is possible
to fix the saw’s drag function with the locking screw
for drag guide (24) in rear position. If the cutting width
exceeds 100 mm, you must ensure that the locking
screw for drag guide (24) is slackened and that the
machine head (4) can be moved.
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut at the stop rail
(11) and on the turntable (17).
Lock the material with the clamping device (8) on
the fixed saw table (18) to prevent the material
from moving during the cutting operation.
Push down the release lever (3) to release the
machine head (4).
Press the ON/OFF switch (2) to start the motor.
With the drag guide (23) fixed in place: Use the
handle (1) to move the machine head (4) steadily
21
GB
Anleitung_BT_SM_2131_Dual_SPK7:_ 14.10.2010 15:39 Uhr Seite 21

Содержание

Похожие устройства

Скачать