Hitachi G13YC [8/49] English
![Hitachi G13YC [8/49] English](/views2/1081320/page8/bg8.png)
7
English
2. Disassembling
Follow the above procedures in reverse.
CAUTIONS
䡬 Comfirm that the depressed center wheel is mounted
firmly.
䡬 Confirm that the spindel lock mechanism is
disengaged by pushing push button two or three
times before switching the power tool on.
MAINTENANCE AND INSPECTION
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of
cracks and surface defects.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Inspecting the carbon brushes (Fig. 5)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brushes with new ones having the same carbon
brush No. shown in the figure when it becomes
worn to or near the “wear limit”. In addition, always
keep carbon brushes clean and ensue that they
slide freely within the brush holders.
4. Replacing carbon brushes (Fig. 6)
〈
Disassembly
〉
(1) Loosen the D4 tapping screw retaining the tail cover
and remove the tail cover.
(2) Use the auxiliary hexagonal wrench or small
screwdriver to pull up the edge of the spring that
is holding down the carbon brush. Remove the
edge of the spring toward the outside of the brush
holder.
(3) Remove the end of the pig-tail on the carbon brush
from the terminal section of brush holder and then
remove the carbon brush form the brush holder.
〈Assembly〉
(1) Insert the end of the pig-tail of the carbon brush
in the terminal section of brush holder.
(2) Insert the carbon brush in the brush holder.
(3) Use the auxiliary hexagonal wrench or small
screwdriver to return the edge of the spring to the
head of the carbon brush.
(4) Mount the tail cover and tighten the D4 tapping
screw.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION:
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS:
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to
EN 60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 95 dB (A)
Measured A-weighted sound pressure level: 84 dB (A)
Uncertainty KpA: 3 dB (A)
Wear ear protection.
The typical weighted root mean square acceleration
value: 2.5 m/s
2
.
Содержание
- Electronic disc grinder winkelschleifer 1
- G 15yc 1
- Szlifierka kątowa sarokcsíszoló úhlová bruska s elektronikou elektronik devir ayarlı avuç taßlama ìöîoçaó åîëùoçaîëìaó ïaåëìa 1
- Ïâîùúôóèîfi ùˆóè fi úô fi ïâè óû∠îô 1
- G 13yc g 15yc 2
- G 15yc 2
- English 5
- General safety rules 5
- Applications 6
- English 6
- Precautions on using disc grinder 6
- Prior to operation 6
- Specifications 6
- Standard accessories 6
- Assembling and disassembling the depressed center wheel fig 1 7
- English 7
- Practical grinder application 7
- English 8
- Maintenance and inspection 8
- Allgemeine sicherheitsmassnahmen 9
- Deutsch 9
- Deutsch 10
- Standardzubehör 10
- Technische daten 10
- Vorsichtsmassnahmen bei der benutzung des winkelschleifers 10
- Anwendungsgebiete 11
- Deutsch 11
- Praktische schleifarbeit 11
- Vor inbetriebnahme 11
- Anbringen und abnehmen der schleifscheibe abb 1 12
- Deutsch 12
- Wartung und inspektion 12
- Deutsch 13
- Ïïëóèî 14
- Π õ ª ƒ º π 14
- Kanonika e apthmata 15
- Ã π ã ƒ ƒπ π 15
- Ïïëóèî 15
- Ƒ ºà π ª ƒ ø ムà π à π 15
- º ƒª 16
- Ïïëóèî 16
- Ƒ π º ƒª à π 16
- Ƒπ π àƒ π 16
- À ã ª øª à ƒπ ƒ ã à 17
- À ƒ π ã 17
- À ƒª π à ƒª 17
- Èî 1 17
- Ïïëóèî 17
- Ïïëóèî 18
- Ogólne wskazówki bezpieczeństwa 19
- Polski 19
- Dane techniczne 20
- Polski 20
- Przed użyciem 20
- Wyposażenie standardowe 20
- Zastosowanie 20
- Środki ostrożności przy używaniu szlifierki tarczowej 20
- Polski 21
- Praktyczne zastosowanie szlifierki 21
- Konserwacja i inspekcja 22
- Polski 22
- Składanie i rozkładanie obniżonych tarcz śsrodkowych rys 1 22
- Magyar 23
- Általános biztonságtechnikai e 23
- A tárcsás kéziköszörű használatára vonatkozó óvintézkedések 24
- Alkalmazások 24
- Az üzembehelyezés előtti tennivalók 24
- Magyar 24
- Műszaki adatok 24
- A kéziköszörű gyakorlati kezelése 25
- Magyar 25
- A süllyesztett közepű tárcsa összeszerelése és szétszerelése 1 ábra 26
- Ellenőrzés és karbantartás 26
- Magyar 26
- Magyar 27
- Všeobecné bezpečnostní předpisy 28
- Čeština 28
- Parametry 29
- Použití 29
- Před použitím 29
- Standardní příslušenství 29
- Upozornění pro používání kotoučové brusky 29
- Čeština 29
- Montáž a demontáž brusného kotouče obr 1 30
- Praktické použití brusky 30
- Čeština 30
- Údržba a kontrola 31
- Čeština 31
- Genel güvenlik kurallari 32
- Türkçe 32
- Aletó kullanim öncesónde 33
- Dósk taílama aletónó kullanirken alinacak önlemler 33
- Standart aksesuarlar 33
- Teknók özellókler 33
- Türkçe 33
- Uygulamalar 33
- Pratók taílama uygulamalari 34
- Tek tarafi oyuk taílama dóskónón takilip çikarilmasi íekil 1 34
- Türkçe 34
- Bakim ve ónceleme 35
- Türkçe 35
- Oåôàe èpabàãa èo texhàke åeâoèachoctà 36
- Pyccíëè 36
- Mmepõ èpeñoctopoühoctà èpà ùkcèãìatañàà òãàîobaãúhoâ maòàhõ 37
- Pyccíëè 37
- Ctahñapthõe akceccìapõ 38
- Oåãactú èpàmehehàü 38
- Pyccíëè 38
- Texhàóeckàe xapaktepàctàkà 38
- Èoñéotobka k ùkcèãìatañàà 38
- Pyccíëè 39
- Èpaktàóeckoe èpàmehehàe òãàîobaãúhoâ maòàhõ 39
- Pyccíëè 40
- Texhàóeckoe oåcãìüàbahàe à èpobepka 40
- Ìctahobka à chütàe òãàîobaãúhoéo kpìéa c ìtoèãehhõm ñehtpom pëc 1 40
- Pyccíëè 41
- Head office in japan 49
- Hitachi koki co ltd 49
- Hitachi power tools europe gmbh 49
- K kato board director 49
- Representative office in europe 49
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 49
- Siemensring 34 47877 willich 1 f r germany 49
Похожие устройства
- Polaris PWK 1503CA White/Brown Инструкция по эксплуатации
- LG 42PC1RR Инструкция по эксплуатации
- LG ARNU09GSEL2 Инструкция по эксплуатации
- Mystery MCM-5015 Инструкция по эксплуатации
- LG 42PJ250 Инструкция по эксплуатации
- Philips Avance HU4901/01 Инструкция по эксплуатации
- LG ARNU09GSEL1 Инструкция по эксплуатации
- LG 42PJ650 Инструкция по эксплуатации
- LG ARNU09GCEA2 Инструкция по эксплуатации
- Polaris PMG 1804 CHROME Инструкция по эксплуатации
- LG 42PN450B Инструкция по эксплуатации
- Bork C802 Инструкция по эксплуатации
- LG 50PA4500 Инструкция по эксплуатации
- LG ARNU09GBHA2 Инструкция по эксплуатации
- Rowenta BRUSH ACTIV VOLUME & SHINE CF9320D0 Инструкция по эксплуатации
- LG 50PB560U Инструкция по эксплуатации
- Rowenta CV7410D6 Инструкция по эксплуатации
- LG ARNU09GB1G1 Инструкция по эксплуатации
- LG 50PB560V Инструкция по эксплуатации
- Rowenta YD3042F0 Инструкция по эксплуатации