![Makita DRS780Z без акк. и з.у [11/40] Operation](/img/pdf.png)
Makita DRS780Z без акк. и з.у [11/40] Operation
![Makita DRS780Z без акк. и з.у [11/40] Operation](/views2/1630758/page11/bgb.png)
11 ENGLISH
For tool with the ring
12
3
4
5
6
15.88
15.88
15.88
► 1. Mounting shaft 2. Inner ange 3. Circular saw
blade 4. Outer ange 5. Hex bolt 6. Ring
WARNING: BE SURE TO TIGHTEN THE HEX
BOLT COUNTERCLOCKWISE SECURELY. Also
be careful not to tighten the bolt forcibly. Slipping
your hand from the hex wrench can cause a per-
sonal injury.
WARNING: If the ring is needed to mount the
blade onto the spindle, always be sure that the
correct ring for the blade's arbor hole you intend
to use is installed between the inner and the outer
anges. Use of the incorrect arbor hole ring may
result in the improper mounting of the blade causing
blade movement and severe vibration resulting in
possible loss of control during operation and in seri-
ous personal injury.
Blade guard cleaning
When changing the circular saw blade, make sure to
also clean the upper and lower blade guards of accu-
mulated sawdust as discussed in the Maintenance
section. Such efforts do not replace the need to check
lower guard operation before each use.
OPERATION
CAUTION: Be sure to move the tool forward
in a straight line gently. Forcing or twisting the tool
will result in overheating the motor and dangerous
kickback, possibly causing severe injury.
NOTE: When the battery cartridge temperature is
low, the tool may not work to its full capacity. At this
time, for example, use the tool for a light-duty cut for
a while until the battery cartridge warms up as high
as room temperature. Then, the tool can work to its
full capacity.
Hold the tool rmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool.
If both hands are holding saw, they cannot be cut by
the circular saw blade. Set the base on the workpiece
to be cut without the circular saw blade making any
contact. Then turn the tool on and wait until the circular
saw blade attains full speed. Now simply move the tool
forward over the workpiece surface, keeping it at and
advancing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and your
speed of advance uniform. If the cut fails to properly follow
your intended cut line, do not attempt to turn or force the
tool back to the cut line. Doing so may bind the circular
saw blade and lead to dangerous kickback and possible
serious injury. Release switch, wait for circular saw blade
to stop and then withdraw tool. Realign tool on new cut
line, and start cut again. Attempt to avoid positioning
which exposes operator to chips and wood dust being
ejected from saw. Use eye protection to help avoid injury.
Hook
CAUTION: Always remove the batteries when
hanging the tool with the hook.
CAUTION: Never hook the tool at high loca-
tions or on the surfaces where the tool may lose
the balance and fall.
CAUTION: Do not pull the tool hooked
downward.
The hook is convenient for hanging the tool temporarily.
To use the hook, simply lift up hook until it snaps into
the open position.
When not in use, always lower hook until it snaps into
the closed position.
1
► 1. Hook
Содержание
- Cordless rear handle saw scie circulaire sans fil à poignée arrière sierra inalámbrica de empuñadura posterior 1
- Drs780 1
- Instruction manual manuel d instruction manual de instrucciones 1
- English original instructions 2
- General power tool safety warnings 2
- Safety warnings 2
- Save all warnings and instruc tions for future reference 2
- Specifications 2
- Warning 2
- Cordless circular saw safety warnings 3
- Important safety instructions for battery cartridge 5
- Save these instructions 5
- Symbols 5
- Warning 5
- Caution 6
- Functional description 6
- Installing or removing battery cartridge 6
- Save these instructions 6
- Tips for maintaining maximum battery life 6
- Caution 7
- Indicating the remaining battery capacity 7
- Overdischarge protection 7
- Overheat protection 7
- Overload alert 7
- Overload protection 7
- Tool battery protection system 7
- Adjusting depth of cut 8
- Automatic speed change function 8
- Bevel cutting 8
- Caution 8
- Positive stopper 8
- Assembly 9
- Caution 9
- Electric brake 9
- Notice 9
- Removing or installing circular saw blade 9
- Sighting 9
- Switch action 9
- Warning 9
- For tool with the inner flange for a 15 8 mm hole diameter saw blade country specific 10
- Blade guard cleaning 11
- Caution 11
- Operation 11
- Warning 11
- Adjusting 0 cut accuracy 12
- Caution 12
- Maintenance 12
- Notice 12
- Optional accessories 12
- Rip fence guide rule 12
- Makita limited one year warranty 13
- Warranty policy 13
- Conservez toutes les mises en garde et instructions pour réfé rence future 14
- Consignes de sécurité 14
- Consignes de sécurité générales pour outils électriques 14
- Français mode d emploi original 14
- Mise en garde 14
- Spécifications 14
- Consignes de sécurité pour scie circulaire sans fil 16
- Conservez ce mode d emploi 18
- Consignes de sécurité importantes pour la batterie 18
- Mise en garde 18
- Symboles 18
- Attention 19
- Conseils pour maintenir la durée de service maximale de la batterie 19
- Conservez ces instructions 19
- Description du fonctionnement 19
- Installation ou retrait de la batterie 19
- Alerte de surcharge 20
- Attention 20
- Dispositif de protection de l outil et de la batterie 20
- Indication de la charge restante de la batterie 20
- Protection contre la décharge excessive 20
- Protection contre la surcharge 20
- Protection contre la surchauffe 20
- Affichage de la charge restante de la batterie 21
- Attention 21
- Fonction de changement de vitesse automatique 21
- Réglage de la profondeur de coupe 21
- Butée fixe 22
- Coupe en biseau 22
- Interrupteur 22
- Mise en garde 22
- Visée 22
- Assemblage 23
- Attention 23
- Frein électrique 23
- Retrait ou pose de la lame de scie circulaire 23
- Attention 24
- Mise en garde 24
- Nettoyage du protecteur de lame 24
- Pour l outil avec bague interne pour lame de scie à orifice intérieur d un diamètre de 15 88 mm spécifique au pays 24
- Utilisation 24
- Attention 25
- Crochet 25
- Entretien 25
- Garde parallèle règle de guidage 25
- Réglage de la précision de coupe 0 25
- Accessoires en option 26
- Attention 26
- Garantie limitée d un an de makita 26
- Politique de garantie 26
- Advertencia 27
- Advertencias de seguridad 27
- Advertencias generales de seguridad para herramientas eléctricas 27
- Conserve todas las advertencias e instrucciones como referencia en el futuro 27
- Español instrucciones originales 27
- Especificaciones 27
- Advertencias de seguridad para la sierra circular inalámbrica 29
- Advertencia 31
- Guarde estas instrucciones 31
- Instrucciones importantes de seguridad para el cartucho de batería 31
- Símbolos 31
- Consejos para alargar al máximo la vida útil de la batería 32
- Descripción del funcionamiento 32
- Guarde estas instrucciones 32
- Instalación o extracción del cartucho de batería 32
- Precaución 32
- Alerta de sobrecarga 33
- Indicación de capacidad restante de la batería 33
- Precaución 33
- Protección contra sobrecalentamiento 33
- Protección contra sobrecarga 33
- Protección contra sobredescarga 33
- Sistema de protección para la herramienta batería 33
- Ajuste de la profundidad de corte 34
- Función de cambio de velocidad automática 34
- Indicación de la capacidad restante de la batería 34
- Precaución 34
- Accionamiento del interruptor 35
- Advertencia 35
- Corte en bisel 35
- Guía visual 35
- Tope de seguridad 35
- Extracción o instalación del disco de la sierra circular 36
- Freno eléctrico 36
- Montaje 36
- Precaución 36
- Advertencia 37
- Limpieza del protector del disco 37
- Operación 37
- Para una herramienta con brida interior para un disco de la sierra con un orificio de 15 88 mm de diámetro en función del país 37
- Precaución 37
- Ajuste de la precisión del corte a 0 38
- Gancho 38
- Mantenimiento 38
- Precaución 38
- Tope lateral de corte regla guía 38
- Accesorios opcionales 39
- Garantía limitada de un año de makita 39
- Precaución 39
- Ésta garantía no aplica para méxico política de garantía 39
- Advertencia 40
- Makita corporation 40
- Warning 40
- Www makita com 40
Похожие устройства
- Makita DTD155Z без акк. и з.у Инструкция по эксплуатации
- Makita HR166DZ без акк. и з.у Инструкция по эксплуатации
- Makita JV102DZ без акк. и з.у Инструкция по эксплуатации
- Makita JV103DZ без акк. и з.у Инструкция по эксплуатации
- Makita SD100DZ без акк. и з.у Инструкция по эксплуатации
- Makita DHR171Z без акк. и з.у Инструкция по эксплуатации
- СОЮЗ КПС-24600 Инструкция по эксплуатации
- BLACK & DECKER BL186KB Инструкция по эксплуатации
- Bosch EasyCut 50 (06033C8020) Инструкция по эксплуатации
- Steinel GLUEMATIC 3002 (333317) Инструкция по эксплуатации
- Metabo GB 18 LTX BL Q I (603828840) без акк и з.у Инструкция по эксплуатации
- Bosch Пила циркулярная GKS 12 V-LI (06016A1000) +Аккумулятор 12 В20Ач LiION (1600Z0002X) Инструкция по эксплуатации
- Bosch Пила циркулярная GKS 12V-26 ProfessionalI (06016A1001) без акк. и з.у+Аккумулятор 12 В20Ач LiION (1600Z0002X) Руководство пользователя
- Bosch Рубанок GHO 12V-20 (06015A7000) без акк. и з.у +Аккумулятор 12 В20Ач LiION (1600Z0002X) Инструкция по эксплуатации
- Bosch AdvancedGrind 18 (06033D3100) без акк. и з.у Инструкция по эксплуатации
- Bosch PSA 18 LI (06033B2301) без акк. и з.у Инструкция по эксплуатации
- Bosch AdvancedOrbit 18 (06033D2100) без акк. и з.у Инструкция по эксплуатации
- Bosch AdvancedCut 18 Set (06033D5101) Инструкция по эксплуатации
- Bosch AdvancedCut 18 (06033D5100) без акк. и з.у Инструкция по эксплуатации
- Makita DSC191Z Инструкция по эксплуатации