Главная
Skipped breadcrumb items
PXC GE-GS 18 Li-Solo (3408220) без АКБ и ЗУ
Инструкция по эксплуатации Страница: 18

Главная
Einhell
PXC GE-GS 18 Li-Solo (3408220) без АКБ и ЗУ
Инструкция по эксплуатации Страница: 18

Einhell PXC GE-GS 18 Li-Solo (3408220) без АКБ и ЗУ — инструкция по эксплуатации и обслуживанию аккумуляторного инструмента [18/124]

Превью страниц Страница 18 / 124

Einhell PXC GE-GS 18 Li-Solo (3408220) без АКБ и ЗУ [18/124] Operation

- 18 -

then begin to blink.

3. Push the battery pack onto the battery char-

ger.

In section 10 (Charger indicator) you will ﬁ nd a

table with an explanation of the LED indicator on

the charger.

If the battery pack fails to charge, check for the

following:

•

voltage at the power socket

•

whether there is good contact at the charging

contacts of the charging unit.

If the battery pack still fails to charge, send

•

the charger and charging adapter

•

and the battery pack

•

to our customer service center.

5.4 Battery capacity indicator (Fig. 4/Item D)

Press the button for the battery capacity indicator

(E). The battery capacity indicator (D) will indicate

the charge status of the battery by means of 3

LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a

defective battery pack.

6. Operation

6.1 On/Oﬀ switch (Fig. 1/Item 1)

Switching on:

Press the locking button (2) and the On/Oﬀ switch

(1).

Inﬁ nitely variable stroke speed control is possible

with the On/Oﬀ switch (1). The further you push

the switch, the higher the stroke speed.

Switching oﬀ :

Release the locking button (2) and the ON/OFF

switch (1) at the same time.

6.2 Using as a universal jig saw (Fig. 6)

Place the universal saw, as shown in Fig. 6, on

the material you want to cut. Switch on the univer-

sal saw and push the universal saw against the

material you want to cut. The cutting speed must

be adjusted to the material.

6.3 Using as a tree pruning saw (Fig. 7)

Place the tree pruning saw, as shown in Fig. 7,

on the branch you want to cut. Switch on the

tree pruning saw and push the tree pruning saw

against the branch you want to cut. The branch

jaw clamp will help you to guide the equipment in

a straight line. The cutting speed must be adjus-

ted to the material.

7. Cleaning, maintenance and

ordering of spare parts

Hazard!

Always pull out the battery pack before starting

any cleaning work.

7.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which

require additional maintenance.

7.3 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

Anl_GE_GS_18_Li_SPK7.indb 18Anl_GE_GS_18_Li_SPK7.indb 18 27.09.2016 11:39:1427.09.2016 11:39:14

Einhell PXC GE-GS 18 Li-Solo (3408220) без АКБ и ЗУ — инструкция по эксплуатации и обслуживанию аккумуляторного инструмента [18/124]

Содержание

Похожие устройства