![Zotek ZTY [6/26] To the line being measured do not touch the](/img/pdf.png)
Zotek ZTY [6/26] To the line being measured do not touch the
![Zotek ZTY [6/26] To the line being measured do not touch the](/views2/1893221/page6/bg6.png)
• Keep fingers behind the finger guards on the
probes.
• When the product has already been connected
to the line being measured, do NOT touch the
input terminal that is not in service.
• Disconnect the test leads from the circuit before
changing the mode.
• When the voltage to be measured exceeds 36V
DC or 25V AC, the operator shall be careful
enough to avoid electric shock.
• Misuse of mode or range can lead to hazards,
be cautious. “ ” will be shown on the display
when the input is out of range.
• Low level of a battery will result in incorrect
readings. Change the batteries when battery
level is low. Do not make measurements when
the battery door is not properly placed.
2
Содержание
- User manual 1
- And limitation of liability 2
- Customers enjoy one year warranty 2
- Disposable batteries damage from 2
- Limited warranty 2
- Input terminals 3
- Instrument overview 3
- Table of contents page 3
- Replace the batteries 5 4
- Introduction 5
- Product only as specified or the protection 5
- Safety information 5
- Vapor or in damp or wet environments 5
- To the line being measured do not touch the 6
- When the input is out of range 6
- Instrument overview 7
- The range 7
- ⑤ diode test 7
- ⑧ secondary measurements display 7
- ⑯ current test ampere 8
- ⑱ primary measurement display 8
- Function buttons 9
- Subtracted from all subsequent readings long 9
- ③ press this button to switch max min test long 9
- Back to the off position and then 10
- Off after 15 minutes of inactivity 10
- You have successfully disabled 10
- Common return terminal for all 12
- Frequency 12
- Measurements instruction 13
- To measure voltage under 99 9mv turn the 13
- Resistance mode the screen will show 14
- Turn the rotary to press select to the 14
- Connect the red probe to the anode side and the 15
- Diode is broken the display reading shows 15
- Measure capacitance 15
- To test diodes connect the red probe to the anode 15
- Turn the rotary switch to press select 16
- Turn the rotary to press select to 17
- The test leads at the correct circuit 18
- Are qualified to do so and have the relevant 19
- Be replaced as below 19
- Clean the product 19
- Maintenance 19
- Loosen the four screws on the back cover and 20
- Of the same type 20
- Specifications 21
- Electrical specifications 22
- Frequency response of acv 40hz 1khz 22
- V 0 01v 22
- V 0 1v 22
- A 0 01a 23
- Ac current 23
- Dc current 23
- Function range resolution accuracy 23
- Ma 0 01ma 23
- Ma 0 1ma 23
- Ma 0 ma 23
- Function range resolution accuracy 24
- Μf 0 1μf 24
- Function range resolution accuracy 25
- Only to 25
Похожие устройства
- Zotek ZTX Инструкция по эксплуатации
- Zotek ZT-300AB Инструкция по эксплуатации
- Zotek ZT-219 Инструкция по эксплуатации
- Zotek ZT-111 Инструкция по эксплуатации
- Zotek ZT-102A Инструкция по эксплуатации
- Zotek ZT-S1 Инструкция по эксплуатации
- Zotek ZT-303 Инструкция по эксплуатации
- Zotek ZT-102 Инструкция по эксплуатации
- Zotek ZT-M1 Инструкция по эксплуатации
- Zotek ZT-109 Инструкция по эксплуатации
- Zotek ZT-A6 Инструкция по эксплуатации
- Zotek ZT-98 Инструкция по эксплуатации
- Zotek ZT-100 Инструкция по эксплуатации
- Zotek ZT-101 Инструкция по эксплуатации
- Zotek ZT-C1 Инструкция по эксплуатации
- Zotek ZT-C2 Инструкция по эксплуатации
- Zotek ZT-C3 Инструкция по эксплуатации
- Zotek ZT-C4 Инструкция по эксплуатации
- Zotek ZT-S2 Инструкция по эксплуатации
- Yli Electronic YK-1068B Спецификация