![Zotek ZTX [10/26] Push once to hold the current reading on the](/img/pdf.png)
Zotek ZTX [10/26] Push once to hold the current reading on the
![Zotek ZTX [10/26] Push once to hold the current reading on the](/views2/1893222/page10/bga.png)
6
②
Push
once to hold the current reading on
the
display
; push again to continue
normal
operation
.
Push
for more than 2 seconds to enter
the
relative
mode. The product will store the
present
reading
as a reference for subsequent
readings.
The
display is zeroed, and the stored reading
is
subtracted
from all subsequent readings. Long
-
push
again to exit the relative mode.
③
Push
this button to toggle between
testing
modes
of DCV, ACV, and NCV.
④
Push
this button to toggle between
testing
modes
of DCmV ( ＜ 99.99mV), ACmV(
＜
99
.99mV), and Temperature.
⑤
Push
this button to toggle between
testing
modes
of Resistance, Diode/Continuity,
and
Capacitance
.
⑥
Push
this button once to enter the manual
range
mode
. In manual range mode, each
push
increases
the range; when the highest range
is
reached,
the next push will lead to the
lowest
range
. To exit the manual range mode,
push
the
button for more than 2 seconds.
Содержание
- User manual 1
- And limitation of liability 2
- Customers enjoy one year warranty 2
- Failures caused by use outside of the 2
- Limited warranty 2
- Table of contents page 3
- Maintenance 5 4
- Buttons with a triple display 5
- Introduction 5
- Look for cracks or missing plastic carefully look 5
- Personal injury please read all safety information 5
- Safety information 5
- To the line being measured do not touch the 6
- When the input is out of range 6
- Instrument overview 7
- The range 7
- ⑭ analog bar graph 8
- ⑯ current test ampere 8
- Minutes of inactivity 9
- Successfully disabled the function 9
- Modes of dcv acv and ncv 10
- Push once to hold the current reading on the 10
- The display is zeroed and the stored reading is 10
- Push this button when the product is at the 11
- Setting of acmv the primary measurement 11
- Measurements instruction 13
- To be measured if the previous setting was 13
- Touch the probes to the correct test points of 13
- And the test lead to the vωhz terminal 14
- Measure capacitance 15
- Reading shows 15
- 100khz push until the product is at the 16
- Capacitor being tested 16
- Frequency while the secondary measurement 16
- When the frequency to be measured is 17
- Are qualified to do so and have the relevant 19
- Clean the product 19
- Maintenance 19
- Product 19
- Loosen the four screws on the back cover and 20
- Of the same type 20
- Place the back cover and the battery door 20
- General specifications 21
- Operating 21
- Specifications 21
- Dc voltage 22
- Electrical specifications 22
- Mv 0 1mv 22
- V 0 01v 22
- Capacitance 24
- Function range resolution accuracy 24
- Mhz 0 01mhz 24
- Only to 24
- Μf 0 01μf 24
- Continuity 25
- Function range resolution accuracy 25
Похожие устройства
- Zotek ZT-300AB Инструкция по эксплуатации
- Zotek ZT-219 Инструкция по эксплуатации
- Zotek ZT-111 Инструкция по эксплуатации
- Zotek ZT-102A Инструкция по эксплуатации
- Zotek ZT-S1 Инструкция по эксплуатации
- Zotek ZT-303 Инструкция по эксплуатации
- Zotek ZT-102 Инструкция по эксплуатации
- Zotek ZT-M1 Инструкция по эксплуатации
- Zotek ZT-109 Инструкция по эксплуатации
- Zotek ZT-A6 Инструкция по эксплуатации
- Zotek ZT-98 Инструкция по эксплуатации
- Zotek ZT-100 Инструкция по эксплуатации
- Zotek ZT-101 Инструкция по эксплуатации
- Zotek ZT-C1 Инструкция по эксплуатации
- Zotek ZT-C2 Инструкция по эксплуатации
- Zotek ZT-C3 Инструкция по эксплуатации
- Zotek ZT-C4 Инструкция по эксплуатации
- Zotek ZT-S2 Инструкция по эксплуатации
- Yli Electronic YK-1068B Спецификация
- Zotek ZT-S3 Инструкция по эксплуатации