![Gigabyte B650E AORUS TACHYON [8/45] 2 product specifications](/img/pdf.png)
Gigabyte B650E AORUS TACHYON [8/45] 2 product specifications
![Gigabyte B650E AORUS TACHYON [8/45] 2 product specifications](/views2/1920072/page8/bg8.png)
- 8 -
2-2 ProductSpecications
CPU AMD Socket AM5, support for:
AMD Ryzen
™
7000 Series Processors
(Go to GIGABYTE's website for the latest CPU support list.)
Chipset AMD B650
Memory Support for DDR5 5200/4800/4400 MT/s memory modules
2 x DDR5 DIMM sockets supporting up to 64 GB (32 GB single DIMM capacity)
of system memory
Dual channel memory architecture
Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in
non-ECC mode)
Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
Support for AMD EXtended Proles for Overclocking (AMD EXPO
™
) and Extreme
Memory Prole (XMP) memory modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory
modules.)
Onboard
Graphics
Integrated Graphics Processor:
- 1 x HDMI port, supporting a maximum resolution of 4096x2160@60 Hz
* Support for HDMI 2.1 version and HDCP 2.3.
** Support native HDMI 2.1 TMDS compatible ports.
(Graphics specications may vary depending on CPU support.)
Audio Realtek
®
ALC1220-VB CODEC
* The back panel line out jack supports DSD audio.
Support for DTS:X
®
Ultra
High Denition Audio
2/4/5.1/7.1-channel
Support for S/PDIF Out
LAN Intel
®
2.5GbE LAN chip (2.5 Gbps/1 Gbps/100 Mbps)
Wireless
Communication
Module
AMD Wi-Fi 6E RZ616 (MT7922A22M)
- WIFI a, b, g, n, ac, ax, supporting 2.4/5/6 GHz carrier frequency bands
- BLUETOOTH 5.2
- Support for 11ax 160MHz wireless standard and up to 2.4 Gbps data rate
(Actual data rate may vary depending on environment and equipment.)
Expansion Slots CPU:
- 1 x PCI Express x16 slot, supporting PCIe 5.0
(Note)
and running at x16
(PCIEX16)
* For optimum performance, if only one PCI Express graphics card is to be installed,
be sure to install it in the PCIEX16 slot.
Chipset:
- 1 x PCI Express x16 slot, supporting PCIe 4.0 and running at x4 (PCIEX4)
* The PCIEX4 slot shares bandwidth with the M2C_SB connector. The PCIEX4 slot
becomes unavailable when a device is installed in the M2C_SB connector.
(Note) Actual support may vary by CPU.
Содержание
- B650e aorus tachyon 1
- Rev 1001 1
- User s manual 1
- Copyright 2
- Disclaimer 2
- Identifying your motherboard revision 2
- Chapter 1 product introduction 3
- Chapter 2 hardware installation 3
- Chapter 3 bios setup 3 3
- Chapter 4 installing the operating system and drivers 5 3
- Chapter 5 appendix 7 3
- Table of contents 3
- 1 motherboard layout 4
- B650e aorus tachyon 4
- Chapter 1 product introduction 4
- Note for debug code information please refer to chapter 5 4
- 2 motherboard block diagram 5
- Note actual support may vary by cpu 5
- Pci express x16 5
- 3 box contents 6
- 1 installation precautions 7
- Chapter 2 hardware installation 7
- 2 product specifications 8
- 2 productspecifications 8
- 3 installing the cpu and cpu cooler 11
- A note the cpu orientation 11
- B installing the cpu 12
- Do not force to engage the cpu socket locking lever when the cpu is not installed correctly as this would damage the cpu and cpu socket 12
- Follow the steps below to correctly install the cpu into the motherboard cpu socket 12
- Be sure to install the cpu cooler after installing the cpu actual installation process may differ depending the cpu cooler to be used refer to the user s manual for your cpu cooler 13
- C installing the cpu cooler 13
- 4 installing the memory 14
- Dualchannelmemoryconfiguration 14
- 5 installing an expansion card 15
- 6 back panel connectors 16
- Hdmi port 16
- Oc ignition button 16
- Ps 2 keyboard and ps 2 mouse ports 16
- Q flash plus button 16
- Rj 45 lan port 16
- Sma antenna connectors 2t2r 16
- Usb 3 gen 1 port 16
- Usb 3 gen 2 type a port red 16
- Center subwoofer speaker out 17
- Line in side speaker out 17
- Line out front speaker out 17
- Mic in side speaker out 17
- Optical s pdif out connector 17
- Port with usb 3 gen 2 support 17
- Rear speaker out 17
- Usb 3 gen 2 type a port red q flash plus port 17
- Usb type 17
- 7 onboard buttons switches and leds 18
- Backup bios boot from the backup bios 18
- Bbios_led the backup bios is active 18
- Bios led indicators 18
- Bios switch and bios led indicators 18
- Bios_sw 18
- Cpu cpu status led dram memory status led vga graphics card status led boot operating system status led 18
- Main bios boot from the main bios 18
- Mbios_led the main bios is active 18
- Status leds 18
- The bios switch bios_sw allows users to easily select a different bios for boot up or overclocking helping to reduce bios failure during overclocking the led indicator mbios_led bbios_led shows which bios is active 18
- The status leds show whether the cpu memory graphics card and operating system are working properly after system power on if the cpu dram vga led is on that means the corresponding device is not working normally if the boot led is on that means you haven t entered the operating system yet 18
- Cold reset button rty use this button to force your system to reboot this is usually used if a cpu crash or memory errors occur or warm reset doesn t work when tuning your system settings hitting this button to force the system to shutdown and boot again 19
- Cpu clock down button clk this button allows you to manually decrease the cpu external clock press once to decrease the external clock by 0 mhz or you can remap this button to lower the cpu multiplier in the bios so you can press once to decrease the cpu multiplier by one you can press the button continuously to adjust the value 19
- Cpu clock up button clk this button allows you to manually increase the cpu external clock press once to increase the external clock by 0 mhz or you can remap this button to raise the cpu multiplier in the bios so you can press once to increase the cpu multiplier by one you can press the button continuously to adjust the value 19
- Gigabyte s unique oc buttons help enthusiasts and overclockers not only get the most performance from their hardware but also the absolute most enjoyable oc experience with features like overclocking the cpu in real time automatically loading the most optimized overclocking configuration for the processor and memory and loading users customized settings etc 19
- Oc buttons 19
- Oc trigger switch tgr_sw this switch can be used to lower the cpu frequency to cool down the cpu temperature before running a benchmark without having to change any software settings instantly setting the tgr switch back to its default position when the benchmark begins will revert the cpu frequency to the original value 19
- Protection mode button limp_mode this button allows the system to automatically reboot with default or safe settings without having to clear cmos settings first this is useful in situations when users fail to boot up the system with their self defined memory parameters 19
- Reserved switch rsv_sw this switch is reserved for hardware expansion a single phase power design is reserved for future use 19
- Safe frequency using the lowest cpu ratio which may vary by cpu 19
- Target frequency set in bios setup or other overclocking application 19
- After system restart go to bios setup to load factory defaults select load optimized defaults or 20
- Always turn off your computer and unplug the power cord from the power outlet before using 20
- Data loss or damage may occur 20
- Do not use the clear cmos button when the system is on or the system may shutdown and 20
- Manually configure the bios settings please navigate to the bios setup page of gigabyte s website for more information 20
- Pwr power button reset reset button cmos clear cmos button 20
- Quick buttons 20
- The clear cmos button 20
- This motherboard has 3 quick buttons power button reset button and clear cmos button the power button and reset button allow users to quickly turn on off or reset the computer in an open case environment when they want to change hardware components or conduct hardware testing 20
- Use a multimeter to measure the following motherboard voltages 20
- Use this button to clear the bios configuration and reset the cmos values to factory defaults when needed 20
- Voltage measurement points 20
- 8 internal connectors 21
- 12v 22 5v 22
- 12v only for 2x12 pin atx 22
- 12v only for 2x4 pin 12v 22
- 2 atx_12v atx_12v1 atx 2x4 12v power connectors and 2x12 main power connector 22
- 3 v 13 3 v 22
- 3 v 14 12v 22
- 3 v only for 2x12 pin atx 22
- 5v 16 ps_on soft on off 22
- 5v 18 gnd 22
- 5v only for 2x12 pin atx 22
- 5vsb stand by 5v 21 5v 22
- Gnd 15 gnd 22
- Gnd 17 gnd 22
- Gnd 19 gnd 22
- Gnd only for 2x12 pin atx 22
- Gnd only for 2x4 pin 12v 22
- Pin no definition 22
- Pin no definition pin no definition 22
- Power good 20 nc 22
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 22
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 22
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 22
- 4 cpu_fan sys_fan1 2 3 4 fan headers 23
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 23
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from 23
- Overheating overheating may result in damage to the cpu or the system may hang 23
- Sys_fan5 6 7_pump system fan water cooling pump headers 23
- The fan pump headers are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis the header also provides speed control for a water cooling pump please navigate to the bios setup page of gigabyte s website and search for smart fan 6 for more information 23
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers 23
- Connect the thermistor cables to the headers for temperature detection 24
- Cpu_opt cpu fan water cooling pump header 24
- Ec_temp1 ec_temp2 temperature sensor headers 24
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design 24
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices 25
- Connect the cpu cooler led strip rgb led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip 25
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip 25
- Cpu_led cpu cooler led strip rgb led strip header 25
- D_led addressable led strip header 25
- For how to turn on off the lights of the led strip please navigate to the unique features page of gigabyte s website 25
- No pin 25
- Pin no definition 25
- The header can be used to connect a cpu cooler led strip or a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m 25
- The header can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds 25
- Led_c rgb led strip header 26
- Noise_sensor noise detection header 26
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is 27
- Bat battery 27
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself 27
- Debug port 27
- Of the battery the positive side should face up 27
- Or uncertain about the battery model 27
- Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 27
- Pin no definition 27
- Replace the battery 4 plug in the power cord and restart your computer 27
- Replaced with an incorrect model 27
- Sata3 0 1 2 3 sata 6gb s connectors 27
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost 27
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the sata connectors support raid 0 raid 1 and raid 10 please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array 27
- To enable hot plugging for the sata ports please navigate to the bios setup page of gigabyte s website and search for sata configuration for more information 27
- Used batteries must be handled in accordance with local environmental regulations 27
- When installing the battery note the orientation of the positive side and the negative side 27
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one minute 27
- Follow the steps below to correctly install an m ssd in the m connector step 1 to access the m slot you want to use unfasten the screws on the motherboard heatsink diagonally to remove the heatsink locate the proper mounting hole for the m ssd to be installed and then install the m ez latch plus clip first 28
- If you want install an m ssd in the 110mm hole that already has a motherboard heatsink standoff be sure to remove the ez latch plus clip first and use the motherboard heatsink screw to secure the heatsink and ssd 28
- Install the m ssd https www gigabyte com webpage 920 m2 latchplus html remove the m ssd https www gigabyte com webpage 921 removem2 html 28
- M pcie x4 ssd m pcie x2 ssd m sata ssd 28
- M2a_cpu a a 28
- M2a_cpu m2b_cpu m2c_sb m socket 3 connectors 28
- M2b_cpu a a 28
- M2c_sb a a 28
- Please visit gigabyte s website for details on using m ez latch plus 28
- Step 2 remove the protective film from the thermal pad on the m connector insert the m ssd into the m connector at an angle step 3 press down on the front end of the m ssd and make sure the m ssd is secured by the m ez latch plus clip remove the protective film from the thermal pad at the bottom of the motherboard heatsink and then replace the heatsink and tighten the screws diagonally 28
- There are two types of m ssds m sata ssds and m pcie ssds this motherboard only supports m pcie ssds please note that an m pcie ssd cannot be used to create a raid set with a sata hard drive please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array 28
- Types of m ssds supported by each m connector 28
- F_panel front panel header 29
- B s_ b 30
- Cc1 18 d 30
- F_audio front panel audio header 30
- F_u320g usb type 30
- F_usb3 f 30
- F_usb3 f_usb30 3 30
- F_usb30 f_ u 30
- Gnd 14 gnd 30
- Head phone detection 30
- Head phone l 30
- Head phone r 30
- Header with usb 3 gen 2x2 support 30
- Mic detection 30
- No pin 30
- Pin no definition 30
- Pin no definition pin no definition 30
- Rx1 15 rx2 30
- Rx1 16 rx2 30
- S 3 b s s s 30
- S b_ b 30
- Sbu1 19 d 30
- Sbu2 20 cc2 30
- Sense_send 30
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 30
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 30
- The header conforms to usb 3 gen 2x2 specification and can provide one usb port 30
- Tx1 12 tx2 30
- Tx1 13 tx2 30
- Usb 0_ b 30
- Vbus 11 vbus 30
- Vbus 17 gnd 30
- _ s f_ 30
- _ s s_ _ b 30
- _ u _ b 30
- B s_ b 31
- D1 18 ssrx2 31
- D1 19 vbus 31
- F_u32 usb 3 gen 1 header 31
- F_u32g2 usb 3 gen 2 type a port 31
- F_usb3 f 31
- F_usb3 f_usb30 3 31
- F_usb30 f_ u 31
- Gnd 14 sstx2 31
- Gnd 17 ssrx2 31
- Nc 20 no pin 31
- Pin no definition pin no definition 31
- S 3 b s s s 31
- S b_ b 31
- Ssrx1 12 d2 31
- Ssrx1 13 gnd 31
- Sstx1 15 sstx2 31
- Sstx1 16 gnd 31
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer 31
- The usb port makes it easier to save data flash the bios or install software in open bench testing platforms whether for extreme overclocking or simply pretesting the pc before final component installation inside a case scenarios where accessing the rear panel io can be an inconvenience 31
- Usb 0_ b 31
- Vbus 11 d2 31
- _ s f_ 31
- _ s s_ _ b 31
- _ u _ b 31
- Chip select 32
- Data input 32
- Data output 32
- F_usb1 usb 2 1 header 32
- No pin 32
- Pin no definition 32
- Power 3 v 32
- Power 5v 32
- Prior to installing the usb bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the usb bracket 32
- Spi_tpm trusted platform module header 32
- The header conforms to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer 32
- Usb dx 32
- Usb dy 32
- You may connect an spi tpm trusted platform module to this header 32
- Chapter 3 bios setup 33
- Function keys 34
- Startup screen 34
- 1 operating system installation 35
- Chapter 4 installing the operating system and drivers 35
- 2 drivers installation 36
- 1 configuring a raid set 37
- 1 configuringaraidset 37
- Before you begin please prepare the following items 37
- Chapter 5 appendix 37
- Raid levels 37
- 2 debug led codes 38
- Regular boot 38
- Recovery 40
- S3 resume 40
- Regulatory notices 42
- United states of america federal communications commission statement 42
- 2 應避免影響附近雷達系統之操作 44
- European community radio equipment directive compliance statement 44
- Japan wireless statement 5 5 ghz 帯 5 5 ghz 帯 屋内のみの使用 44
- Korea kcc ncc wireless statement 5 25ghz 5 35 ghz 대역을 사용하는 무선 장치는 실내에서만 사용하도록 제한됩니다 44
- Ncc wireless statements 無線設備警告聲明 低功率電波輻射性電機管理辦法 1 取得審驗證明之低功率射頻器材 非經核准 公司 商號或使用者均不得擅自變更頻率 加大功率或變更原設計之特 性及功能 低功率射頻器材之使用不得影響飛航安全及干擾合法通信 經發現有干擾現象時 應立即停用 並改善至 無干擾時方得繼續使用 前述合法通信 指依電信管理法規定作業之無線電通信 低功率射頻器材須忍受合法通信或 工業 科學及醫療用電波輻射性電機設備之干擾 44
- This equipment complies with all the requirements and other relevant provisions of radio equipment directive 2014 53 eu this equipment is suitable for home and office use in all the european community member states and efta member states the low band 5 5 5 5 ghz is for indoor use only 44
- Wireless module approvals wireless module manufacturer amd corporation wireless module model name rz616 mediatek mt7922a22m 44
- Contact us 45
- Gigabyte esupport 45
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com 45
Похожие устройства
- Gigabyte B650I AORUS ULTRA Руководство пользователя по BIOS
- Gigabyte B650I AORUS ULTRA Инструкция по эксплуатации
- Gigabyte B650M AORUS ELITE Руководство пользователя по BIOS
- Gigabyte B650M AORUS ELITE Инструкция по эксплуатации
- Gigabyte B650M AORUS ELITE AX Руководство пользователя по BIOS
- Gigabyte B650M AORUS ELITE AX Инструкция по эксплуатации
- Gigabyte B650M AORUS PRO AX Руководство пользователя по BIOS
- Gigabyte B650M AORUS PRO AX Инструкция по эксплуатации
- Gigabyte B650M C Руководство пользователя по BIOS
- Gigabyte B650M C Инструкция по эксплуатации
- Gigabyte B650M DS3H Руководство пользователя по BIOS
- Gigabyte B650M DS3H Инструкция по эксплуатации
- Gigabyte B650M GAMING X AX Руководство пользователя по BIOS
- Gigabyte B650M GAMING X AX Инструкция по эксплуатации
- Gigabyte X570S AERO G Инструкция по эксплуатации
- Gigabyte X570S AORUS ELITE Инструкция по эксплуатации
- Gigabyte X570S AORUS ELITE AX Инструкция по эксплуатации
- Gigabyte X570S AORUS MASTER Инструкция по эксплуатации
- Gigabyte X570S AORUS PRO AX Инструкция по эксплуатации
- Gigabyte X570S GAMING X Инструкция по эксплуатации