Главная
Skipped breadcrumb items
FH-X360UB
Инструкция по эксплуатации Страница: 8

Главная
Pioneer
FH-X360UB
Инструкция по эксплуатации Страница: 8

Pioneer FH-X360UB — инструкция по подключению AUX и настройке системы автомобиля [8/32]

Превью страниц Страница 8 / 32

Black plate (8,1)

4 Turn M.C. to select the system menu

function.

For details, refer to System menu on page 6.

Using an AUX source

1 Insert the stereo mini plug into the AUX

input jack.

2 Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on page 7.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! Source name

! Source name and clock

If an unwanted display appears

Turn off the unwanted display using the proce-

dures listed below.

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select SYSTEM.

3 Turn M.C. to display DEMO OFF and press

to select.

4 Turn M.C. to switch to YES.

5 Press M.C. to select.

Connections

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 W to

8 W (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle’s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.

This unit

1 24

1 Antenna input

2 Fuse (10 A)

3 Power cord input

4 Wired remote input

Hard-wired remote control adapter can be

connected (sold separately).

5 Rear output or subwoofer output

Using this unit

Section

Installation

<QRB3357-A>8

Pioneer FH-X360UB — инструкция по подключению AUX и настройке системы автомобиля [8/32]

Содержание

Похожие устройства