Vitek VT-8317 [4/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-8317 [4/32] English

Vitek VT-8317 [4/32] English
4
ENGLISH
a person who is responsible for their safety or
if they are not instructed by this person on the
usage of the unit.
• Do not use the unit if the power cord or the
power plug is damaged. If the power cord is
damaged, it should be replaced by the man-
ufacturer, a maintenance service or similar
qualified personnel to avoid danger.
• Do not repair the unit by yourself. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and contact any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
• Transport the unit in the original packaging
only.
• Keep the unit out of reach of children and
people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
•
Unpack the iron; remove the protection from the
iron soleplate (14), if any.
•
Check the unit for damages; do not use the iron
in case of damages.
•
Before switching the iron on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
•
There may be water residue in the tank, this
is normal, as the iron has undergone factory
quality control.
Note: When the iron is switched on for the first time
the heating element of the iron burns, therefore
occurrence of foreign smell and a small amount of
smoke is possible, it is normal.
WATER SELECTION
Fil the tank with distilled water only. You can use
tap water to fill the water tank (10). If tap water is
hard, use distilled or demineralized water, this will
prolong service life of the iron.
Note: - Do not fill the water tank (10) with
scented liquids, vinegar, starch solution, descal-
ing reagents, chemical agents etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that it
is unplugged.
•
Set the temperature control knob (11) to the
position «OFF», and the continuous steam sup-
ply knob (3) to the utmost right position - con-
tinuous steam supply is off.
•
Open the water inlet lid (2).
•
Pour water into the water tank (10) and then
close the water inlet lid (2) tightly.
Notes:
– Do not exceed the «MAX» mark (13).
– If you need to refill water during ironing,
switch the iron off and unplug it.
– After you finish ironing, switch the iron off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
IRONING TEMPERATURE
Before operation, test the heated iron on a piece of
cloth to be sure that the iron soleplate (14) and the
water tank (10) are clean.
•
Always check the recommended ironing tem-
perature indicated on the tag before ironing.
•
If there is no tag with recommendations for iron-
ing, but you know the type of fabric, use the
following table to determine proper ironing tem-
perature.
Icons Fabric type (temperature)
Do not iron
•
synthetics, nylon, acrylic, polyester
(low temperature)
••
silk/wool (medium temperature)
•••
cotton/linen (high temperature)
•
This table is only valid for smooth materials.
Fabrics of other types (crimped, raised, etc.) are
best ironed at low temperature.
•
First sort items by ironing temperature: synthet-
ics to synthetics, wool to wool, cotton to cot-
ton etc.
•
The iron heats up faster than it cools down.
For this reason, it is recommended to iron the
items which require low temperature first (for
instance, synthetic fabrics). After that, start iron-
ing at higher temperatures (silk/wool). Cotton
and linen items should be ironed last.
VT-8317.indd 4 7/5/19 2:26 PM

Содержание

Похожие устройства

Скачать