Home
Главная
Skil
Шлифовальная Машина
7207 LK
Инструкция по эксплуатации Страница: 8

Skil 7207 LK Инструкция по эксплуатации онлайн [8/112] 92499

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• SKIL can assure awless functioning of the tool only

when original accessories are used

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A); wear

ear protection

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• When sanding metal, sparks are generated; do not use

dustbag/dustbox and keep other persons and

combustible material from work area

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of sanding sheet 4

! disconnect the plug

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total sanding surface

covered with sanding paper

- mount VELCRO sanding sheet as illustrated

• Mounting support plate (not standard included) 5

- remove VELCRO sanding sheet

- remove delta tip A while pushing button B

- mount support plate C as illustrated

• Mounting special sanding attachments (not standard

included) 6

- mount desired sanding attachment to support plate C

as illustrated

- mount corresponding VELCRO sanding sheet to

sanding attachment

- 3 sanding positions

• Mounting “Louvre” attachment (not standard included)

- remove VELCRO sanding sheet

- remove delta tip A while pushing button B

- mount “Louvre” attachment as illustrated

• Dust suction 8

- mount dustbag G

- empty dustbag regularly for optimal dust pick-up

performance

! do not use dustbag when sanding metal

• On/o switch

- switch on/o the tool by pushing switch H 2 forward/

backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

Содержание

Похожие устройства

Power tools are dangerous in the hands of untrained users e Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools f Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control g Use the power tool accessories and tool bits etc In accordance with these Instructions taking Into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation 5 SERVICE a Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained additives for wood conditioning wear a dust mask and work with a dust extraction device when connectable Follow the dust related national requirements for the materials you want to work with When sanding metal sparks are generated do not use dustbag dustbox and keep other persons and combustible material from work area Do not touch the moving sanding sheet Do not continue to use worn torn or heavily clogged sanding sheets Wear protective gloves safety glasses close fitting clothes and hair protection for long hair Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended SAFETY INSTRUCTIONS FOR SANDERS USE Avoid damage that can be caused by screws nails and other elements in your workpiece remove them before you start working Always keep the cord away from moving parts of the tool direct the cord to the rear away from the tool Secure the workpiece a workpiece clamped with clamping devi ces or i n a vice i s hel d more securely than by hand When you put away the tool switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB A wear ear protection If the cord is damaged or cut through while working do not touch the cord but immediately disconnect the plug Never use the tool when cord is damaged have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply This tool is not suitable for wet sanding Do not work materials containing asbestos asbestos is considered carcinogenic Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhalation of the dust may cause allergic reactions and or respiratory diseases to the operator or bystanders wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with Mounting of sanding sheet I disconnect the plug the dust suction requires the use of perforated sanding sheets I perforation In sanding sheet should correspond with perforation In sanding foot replace worn sanding sheets in time I always use the tool with the total sanding surface covered with sanding paper mountVELCRO sanding sheet as illustrated Mounting support plate not standard included remove VELCRO sanding sheet remove delta tip A while pushing button B mount support plate C as illustrated Mounting special sanding attachments not standard Included mount desired sanding attachment to support plate C as illustrated mount corresponding VELCRO sanding sheet to sanding attachment 3 sanding positions Mounting Louvre attachment not standard included remove VELCRO sanding sheet remove delta tip A while pushing button B mount Louvre attachment as illustrated Dust suction mount dustbag G empty dustbag regularly for optimal dust pick up performance I do not use dustbag when sanding metal On off switch switch on off the tool by pushing switch H forward backwards I before the sanding surface reaches the workpiece you should switch on the tool I before switching off the tool you should lift It from the workpiece 8

Скачать