Maxwell MW-1060 ST [10/44] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Maxwell MW-1060 ST [10/44] English

Maxwell MW-1060 ST [10/44] English
10
ENGLISH
10
– Select the heating temperature with the but-
ton (9) and then touch the button (7) «On/
Off», the unit will start heating.
Note: If the water temperature in the kettle
is higher than the preset one, the unit will
be switched off (the button (7) «On/Off» will
go out).
– Once the water reaches the set tempera-
ture, the kettle will be switched off: you will
hear 2 sound signals, the button (9) illumi-
nation will light constantly. After 1 minute in
standby mode, the button illumination will
go out.
Temperature maintaining
– Cover the kettle with the lid (13) and fix it by
pressing the button (14).
– Place the kettle on the base (5).
– Use the button (9) to select the water tem-
perature 40°, 60° or 80 °С.
– Press the button (8) «Keep warm» and then
press the button (7) «On/Off», the unit will
start heating the water up to preset tem-
perature.
Note: If the water temperature in the kettle
is higher than the preset one, the unit will
be switched off (the button (7) «On/Off» will
go out).
– Once the water reaches the set tempera-
ture, you will hear 2 sound signals and the
kettle will be switched to keep warm mode:
once the water temperature decreases, the
heating switches on automatically, when the
set temperature is reached, the unit will be
switched to standby mode.
Notes:
The button (9) illumination flashes during
heating and lights constantly in standby
mode.
Total keep warm mode duration is 30 min-
utes. In 30 minutes the unit will be switched
off and the buttons illumination will go out.
The unit keeps the keep warm mode set-
tings for 1 minute. If you removed the
kettle from the base and placed it back
within 1 minute, the unit will continue oper-
ating in keep warm mode. If you placed the
kettle on the base after1 minute, reset the
unit again.
The keep warm function is not available for
100 °С.
To switch the keep warm function off, press
the button (8) «Keep warm».
Making tea
– Remove the tea basket (12) from the lid (11)
by turning it in the direction of the «OPEN»
arrow.
– Place the required amount of tea in the tea
basket (12).
– Install the tea basket (12) back to its place
and turn it in the direction of the «LOCK»
arrow.
– Install the tea basket (12) inside the flask (1).
Make sure that the lid (11) is in close contact
with the flask.
– Lift the tea basket (12) pulling by the handle
(11) and fix it in the upper position, the tea
basket will be above the water.
– Set the required water heating temperature
(see above).
– Once the water reaches the set temperature,
put the tea basket (12) in the water.
– When the tea is ready, lift the tea basket (12)
by the lid (11).
Notes:
Do not leave the tea basket (12) in the water
for a long time.
Do not leave the brewed tea and the brewed
tea leaves in the kettle for a long time.
The tea level should not exceed the «Tea
Max» mark.
– If you accidentally switched the kettle on with
insufficient amount of water, the automatic
thermal switch will be on and the kettle will be
switched off. In this case take the kettle off
the base (5) and let it cool down for 5-10 min-
utes. Then fill it with water and switch it on,
the kettle will operate in normal mode.
Attention!
Be careful when handling the glass flask
of the kettle; the flask can be broken if the
kettle was dropped or hit against a metal sink
while water filling.
To avoid burns by hot steam, do not bend
over the kettle spout while it is operating.
CLEANING AND CARE
– Before cleaning, disconnect the unit from the
mains, pour out the water and let the unit cool
down completely.
– Wipe the outer surface of the kettle with a
damp cloth or a sponge. Use soft detergents
to remove dirt. Do not use metal brushes or
abrasives.
MW-1060.indd 10 23.12.2013 14:15:44

Содержание

Похожие устройства

Скачать