Home
Главная
Brayer
Кофеварка
BR-1100
Руководство по эксплуатации Страница: 4

Brayer BR-1100 [4/32] 7 en en

6 7en en

is detected, and after it was dropped, unplug the unit

and apply to the service center.

• Transport the coffee maker in the original package.

• Keep the unit out of reach of children and disabled

• persons.

COFFEE MAKER IS INTENDED FOR HOUSEHOLD

USE ONLY, DO NOT USE THE COFFEE MAKER FOR

COMMERCIAL OR LABORATORY PURPOSES.

BEFORE USING THE COFFEE MAKER

After unit transportation or storage at low

temperature, it is necessary to keep it for at least

three hours at room temperature.

• Unpack the coffee maker and remove all the

packaging materials.

• Keep the original package.

• Check the delivery set.

• Read the safety measures and operating

recommendations.

• Examine the coffee maker for damages, in case of

damage do not plug it into the mains.

• Make sure that the specications of power supply

voltage specied on the lower panel of the unit

correspond to the specications of your mains. When

the unit is used in the mains with 60 Hz frequency, it

does not need any additional settings.

• Wipe the surface of the coffee maker body with a

clean, slightly damp cloth to remove dust.

• Before using the coffee maker for the rst time, wash

all removable parts (5, 6, 13, 15, 17) with warm water

and neutral detergent, rinse and dry them.

• Before switching the unit on, make sure that the

mains voltage corresponds to the voltage specied

on the unit body.

• Make sure that the power switch (16) is in position

«0», and the operation mode switch knob (7) is in

position «

».

• To remove the tank (13), take it by the handle (12)

and remove the tank upwards, ll it with cold water

up to the MAX mark and install it back to its place.

• Insert the coffee lter (6) into the holder (5), matching

the ledge on the lter (6) with the slot on the holder

(5) and turn the lter (6) clockwise/counterclockwise

(do not ll the lter with ground coffee).

• Install the lter holder (5) into the coffee maker. The

holder (5) ledges should match the grooves on the

boiler « », after that turn the lter holder (5)

handle (3) to the right until bumping « ».

• Place a suitable cup on the grid (2).

• Insert the power plug into the mains socket.

• Switch the coffee maker on by setting the power

switch (16) button to the position «I», the indicator (9)

will light up.

• Wait until the boiler heats up, the indicator (8) will

glow white.

• To ll the boiler with water, set the operation mode

switch (7) knob to the position « », wait for 15-20

seconds, or at the rst signs of appearance of water

in the cup, switch the water supply off by setting the

operation mode switch knob (7) to the position « ».

• Set the operation mode switch knob (7) to the

position « » again, after the cup is lled with

water switch the water supply off by setting the

operation mode switch knob (7) to the position « »,

pour the water out of the cup. Depending on the cup

capacity repeat this procedure several times until the

boiler is clean.

• Note: at the rst pumping of water into the boiler

some foreign noise can appear, this is normal, the

unit releases air from the boiler, approximately in 20

seconds foreign noise will stop.

• Coffee strength depends on the quality and grinding

degree of coffee beans. If coffee is pouring out too

long, this means the coffee powder is too ne or it is

tamped too strongly.

PREHEATING

• To make a cup of hot espresso, it is recommended to

preliminary heat up the coffee lter (6) and the lter

holder (5).

• To remove the tank (13), take it by the handle (12)

and remove the tank (13) upwards, ll it with cold

water up to the MAX mark and install it back to its

place.

• Insert the coffee lter (6) into the holder (5), matching

the ledge on the lter (6) with the slot on the holder

(5) and turn the lter (6) clockwise/counterclockwise

(do not ll the lter with ground coffee).

• Install the lter holder (5) into the coffee maker. The

holder (5) ledges should match the grooves on the

boiler « », after that turn the lter holder (5)

handle (3) to the right until bumping « ».

• Place a suitable cup on the grid (2).

• Insert the power plug into the mains socket.

• Switch the coffee maker on by setting the power

switch (16) button to the position «I», the indicator (9)

will light up.

• Wait until the boiler heats up, the indicator (8) will

glow white.

ATTENTION!

Do not remove the lter holder (5) during coffee

maker operation.

AUTO SWITCH OFF FUNCTION

• If no actions were performed during 25 minutes

after switching on, the coffee maker will switch off

automatically.

HOW TO MAKE A GOOD ESPRESSO

• Use ground coffee for espresso coffee makers.

• Slightly tamp the ground coffee in the lter (6), you

can do it with the back side of the measuring spoon

(17).

Brayer BR-1100 [4/32] 7 en en

Содержание

Похожие устройства