ADJ Quad Phase HP — инструкция по эксплуатации и обслуживанию светового оборудования [8/10]
Макгруп McGrp.ru

ADJ Quad Phase HP — инструкция по эксплуатации и обслуживанию светового оборудования [8/10]

Превью страниц Страница 8 / 10
ADJ Quad Phase HP [8/10] Fixture cleaning
ADJ Products, LLC - www.adj.com - Quad Phase HP Instruction Manual Page 15
Quad Phase HP Fuse Replacement
Quad Phase HP Cleaning
Quad Phase HP Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
2. Check the sound sensitivity level.
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
ADJ Products, LLC - www.adj.com - Quad Phase HP Instruction Manual Page 16
Quad Phase HP ADJ-RC1 Operation
The ADJ-RC1 infrared remote (sold seperately) has many differnet
functions and gives you complete control of your Mega Tri 60. To
control the your desired fixture you must aim the controller at the
front of the fixture and be no more the 30 feet away. To use the ADJ
LED RC you must first activate the fixtures infrared receiver, to acti-
vate the receiver please see the instructions on page 10.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
COLOR - Press this button to enter Dimmer mode. Adjust the output
intensity using either the number buttons, or using the “DIMMER +”
and “DIMMER -” buttons.
STROBE - This button will activate the strobe effect. You can control
the flash rate by pressing the “DIMMER +” and “DIMMER -” buttons.
If you press and hold this button the unit will begin to strobe.
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run.
SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.
SHOW - This designates the fixture as a slave fixture in a master/
slave configuration.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the out-
put intensity and to adjust the strobe speed.
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that
the fuse holder is located inside the power socket. Insert a flat-head
screw driver into the power socket and gently pry out the fuse holder.
Remove the bad fuse and replace with a new one. The fuse holder also
has a holder for a spare fuse.

Содержание

55

Похожие устройства

Узнайте, как правильно обслуживать и настраивать световое оборудование. Решение распространенных проблем, советы по чистке и замене предохранителей.

Google Play RuStore