Vitek VT-3003 Инструкция по эксплуатации онлайн [10/28] 811692
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-3003 Инструкция по эксплуатации онлайн [10/28] 811692

Vitek VT-3003 Инструкция по эксплуатации онлайн [10/28] 811692
10
ENGLISH
WARNING: Before installing the whisk (9) and the
gear (8), make sure that the power plug is not inserted
into the mains socket.
•
Insert the whisk attachment (9) into the whisk gear (8).
•
Insert the egg whisk gear (8) into the motor unit
(3) and turn it until corresponding marks on the
gear (8) and the motor unit (3) match, make sure
that the gear (8) and the egg whisk (9) are fixed
properly.
•
Insert the power plug into the mains socket.
•
Make sure that speed control knob (6) is set to
«MIN» position.
•
Immerse the whisk (9) into the bowl with food.
Note: You can put the foodstuffs into the cup (10).
•
To switch the unit on, press and hold down the but-
ton (5).
•
You can adjust speed with speed control knob (6).
•
After you finish using the unit, unplug it, disconnect
the egg whisk gear (8) from the motor unit (3) by
turning it until corresponding marks on the gear (8)
and the motor unit (3) match.
•
Remove the whisk (9) from the gear (8).
ATTENTION!
–
Do not use the whisk attachment (9) to knead tight
dough.
–
Put products into the bowl before switching the unit on.
USING THE CHOPPER
The chopper is used to chop meat, cheese, onion,
herbs, garlic, carrots, walnuts, almonds, prunes, veg-
etables and fruit.
ATTENTION! Do not chop very hard products, such as
ice cubes, frozen products, nutmegs, coffee beans,
cereals etc.
Before you start chopping:
–
Cut meat, cheese, onions, vegetables or fruit into
pieces approximately 2x2 cm in size.
–
Remove stems of herbs, shell nuts.
–
Remove bones, sinews and cartilage from meat.
Chopping
Caution: the blades of the chopping knife (12) are
very sharp!
Always hold the chopping knife (12) by the upper plas-
tic end.
•
Place the chopper bowl (11) on a flat stable surface.
•
Set the chopping knife (12) on the axis inside the
chopper bowl (11).
•
Put the products into the chopper bowl (11).
Note: Do not switch the unit on when the chopper bowl
(11) is empty.
•
Place the geared lid (13) on the chopper bowl (11)
and rotate the geared lid (13) clockwise until it is
fixed.
•
Install the motor unit (3) on the geared lid (13)
feeding chute, turn the motor unit (3) clockwise
until bumping, having matched the correspond-
ing marks on the geared lid (13) and the motor
unit (3), make sure that the motor unit (3) is fixed
properly.
•
Install the motor unit (3) strictly in the vertical posi-
tion and evenly.
•
Connect the unit to the mains by inserting the
power cord plug into the mains socket.
•
Make sure that speed control knob (6) is set to
«MIN» position.
•
To switch the unit on, press and hold the but-
ton (5).
•
You can adjust speed with speed control knob (6).
•
During operation hold the motor unit (3) with one
hand and the chopper bowl (11) with the other
hand.
•
After using the unit, wait until the chopping knife
(12) fully stops.
•
Remove the power plug from the mains socket.
•
Disconnect the motor unit (3) from the geared lid
(13) chute by turning the motor unit (3) counter-
clockwise.
•
Remove the geared lid (13) having turned it coun-
terclockwise.
•
Carefully remove the chopping knife (12) taking it
by the plastic end.
•
Take the chopped products out of the chopper
bowl (11).
ATTENTION! Strictly follow the described sequence
of operations.
Notes: To engage the «Turbo» mode, press and hold
the button (4) for 60 seconds when using blender
attachment (1), 30 seconds when chopping in the
chopper bowl (11). Do not use the whisk attachment
(9) in the «Turbo» mode.
To achieve the best results, refer to the table below:
Products Maximum amount
of foodstuff
Approximate process-
ing time, seconds
Recommended attachment
(whisk, blender, chopper)
Herbs 20 g 10-30 chopper
Meat 250 g 35 chopper
Nuts 200 g 30 chopper
Cheese 150 g 30 whisk
Bread 1 slice 20 chopper
Boiled eggs 2 pcs 90 blender
Onions 100 g 30 chopper

Похожие устройства

Скачать