![Kramer RC-13TC Руководства по эксплуатации онлайн [7/16] 139618](/img/pdf.png)
Kramer RC-13TC Руководства по эксплуатации онлайн [7/16] 139618
![Kramer RC-13TC Руководства по эксплуатации онлайн [7/16] 139618](/views2/1152618/page7/bg7.png)
RC-13TC - Defining the RC-13TC Video Transport Controller 5
Figure 2: RC-13TC Video Transport Controller Rear Panel
# Feature Function
4 KNET TERM Termination Switch Use to set the K-NET bus termination (see
Section
5.2.2)
5 KNET 4-pin Removable Terminal
Blocks (1 and 2)
Connect to a master room controller or to another
auxiliary device.
Connect GND to GND, B to B, A to A, +12V to
+12V (see Section
5.2)
6 RESET (DEFAULT) Factory
Default Reset Button
Press and hold during power-up to erase all
custom programming.
Note: The current LCD text and all button actions
are erased
7 Ring Tongue Terminal Grounding
Screw
Connect to grounding wire (see Section 6)
8 RS-232 3-pin Removable
Terminal Block
For controlling a display, switcher, AV source or
other AV equipment
9 IR Infrared 2-pin Removable
Terminal Blocks (1 and 2)
Connect to IR emitters (see Figure 3).
Connect OUT 1 or OUT 2 to IR+ (anode), GND to
GND (cathode)
10 PROGRAM (USB) Connector Connect to a computer to program the unit ID,
LCD text and button actions using K-Config
Configuration software
11 Power Supply 2-pin Removable
Terminal Block
Connect to power supply (see Section 5.1.2).
Connect GND to GND, +12V to +12V
12 FW UPGRADE Switch For the use of Kramer service personnel only
Содержание
- User manual 1
- Contents 2
- Figures 2
- Introduction 3
- Achieving the best performance 4
- Getting started 4
- Overview 5
- Defining the rc 13tc video transport controller 6
- This section defines the rc 13tc 6
- The rc 13tc as a standalone video transport controller 8
- Using your video transport controller 8
- Connecting a standalone rc 13tc to a power supply 9
- Connecting the rc 13tc as a standalone video transport controller 9
- Connecting multiple rc 13tc devices as system controllers 10
- Setting the k net termination 10
- The rc 13tc as an auxiliary control panel 10
- Operating the rc 13tc video transport controller 11
- Connect the ring tongue terminal to the building grounding point wire we 12
- Figure 7 defines the grounding screw components 12
- Grounding the rc 13tc video transport controller 12
- Insert the m3x6 screw through the toothed lock washers and the tongue 12
- Insert the m3x6 screw with the two toothed lock washers and ring tongue 12
- Preventing static electricity from impacting the performance of the unit 12
- Recommend that you use a green yellow awg 18 0 2mm2 wire crimped 12
- Terminal in the order shown above 12
- Terminal into the grounding screw hole and tighten the screw 12
- The grounding screw is used to earth the chassis of the unit to the building ground 12
- To ground the rc 13tc 12
- We recommend that you ground the rc 13tc 12
- With a proper hand tool 12
- Mounting the faceplate 13
- Technical specifications 14
Похожие устройства
- Kramer WP-500 Руководства по эксплуатации
- Kramer SL-1 Руководства по эксплуатации
- Kramer SL-10 Руководства по эксплуатации
- Kramer SL-12 Руководства по эксплуатации
- Kramer K-Router Plus Руководства по эксплуатации
- Kramer EDID Designer Руководства по эксплуатации
- Kramer K-Config 2 Руководства по эксплуатации
- Kramer Site-CTRL™ Руководства по эксплуатации
- Kramer RC-5B2 Руководства по эксплуатации
- Kramer RC-5B4 Руководства по эксплуатации
- Kramer RC-53D Руководства по эксплуатации
- Kramer RC-53DLC Руководства по эксплуатации
- Kramer RC-54DL Руководства по эксплуатации
- Kramer RC-108 Руководства по эксплуатации
- Kramer RC-116 Руководства по эксплуатации
- Kramer FC-10ETH Руководства по эксплуатации
- Kramer FC-21ETH Руководства по эксплуатации
- Kramer FC-22ETH Руководства по эксплуатации
- Kramer FC-24ETH Руководства по эксплуатации
- Kramer FC-26 Руководства по эксплуатации