Главная
Skipped breadcrumb items
IES-1248 EE
Инструкция по эксплуатации Страница: 123

Главная
Zyxel
IES-1248 EE
Инструкция по эксплуатации Страница: 123

Zyxel IES-1248 EE — настройка переключателей: управление таймерами и приоритетами трафика [123/544]

Превью страниц Страница 123 / 544

Zyxel IES-1248 EE [123/544] Note standalone mode is recommended for network topologies that use loops

Chapter 13 Switch Setup

IES-1248-51/51A/53 User’s Guide

123

Leave All Timer Leave All Timer sets the duration of the Leave All Period timer for GVRP in

milliseconds. Each port has a single Leave All Period timer. Leave All Timer

must be larger than Leave Timer.

Port Isolation

Active

Turn on port isolation to block communications between subscriber ports. When

you enable port isolation you do not need to configure the VLAN to isolate

subscribers.

MAC Anti-Spoofing Select this if you want the IES-1248 to generate an alarm, issue a SNMP trap,

and disable the port when an existing MAC address appears on another port.

Switch Mode Select Standalone to use both of the IES-1248’s Ethernet ports (ENET 1 and

ENET 2) as uplink ports.

Note: Standalone mode is recommended for network topologies

that use loops.

Use Daisychain mode to cascade (daisychain) multiple IES-1248. The IES-

1248 uses Ethernet port one (ENET 1) as an uplink port to connect to the

Ethernet backbone and uses Ethernet port two (ENET 2) to connect to another

(daisychained or subtending) IES-1248.

Note: Daisychain mode is recommended for network topologies

that do not use loops.

Priority Queue

Assignment

IEEE 802.1p defines up to 8 separate traffic types by inserting a tag into a MAC-

layer frame that contains bits to define class of service. Frames without an

explicit priority tag are given the default priority of the ingress port. Use the next

two fields to configure the priority level-to-physical queue mapping.

The device has 4 physical queues that you can map to the 8 priority levels for

outgoing Ethernet traffic. The device has 8 physical queues that you can map to

the 8 priority levels for outgoing ADSL traffic. Traffic assigned to higher index

queues gets through the device faster while traffic in lower index queues is

dropped if the network is congested.

Priority Level The following descriptions are based on the traffic types defined in the IEEE

802.1d standard (which incorporates IEEE 802.1p).

Priority 7 Typically used for network control traffic such as router configuration messages.

Priority 6 Typically used for voice traffic that is especially sensitive to jitter (jitter is the

variations in delay).

Priority 5 Typically used for video that consumes high bandwidth and is sensitive to jitter.

Priority 4 Typically used for controlled load, latency-sensitive traffic such as SNA

(Systems Network Architecture) transactions.

Priority 3 Typically used for “excellent effort” or better than best effort and would include

important business traffic that can tolerate some delay.

Priority 2 This is for “spare bandwidth”.

Priority 1 This is typically used for non-critical “background” traffic such as bulk transfers

that are allowed but that should not affect other applications and users.

Priority 0 Typically used for best-effort traffic.

Apply Click Apply to save your changes to the IES-1248’s volatile memory. The IES-

1248 loses these changes if it is turned off or loses power, so use the Config

Save link on the navigation panel to save your changes to the non-volatile

memory when you are done configuring.

Cancel Click Cancel to begin configuring this screen afresh.

Table 15 Switch Setup (continued)

LABEL DESCRIPTION

Zyxel IES-1248 EE — настройка переключателей: управление таймерами и приоритетами трафика [123/544]

Содержание

Похожие устройства