![Graco ProControl 1KS [27/36] Check resistance](/img/pdf.png)
Graco ProControl 1KS [27/36] Check resistance
![Graco ProControl 1KS [27/36] Check resistance](/views2/1193397/page27/bg1b.png)
Electrical
3A1163A 27
Grounding
Ground the ProControl system as instructed here and in
the individual component manuals. A ground wire and
clamp, part no. 223547, is available from Graco.
NOTE: To prevent electrical noise interference from high
voltage equipment, do not connect the robot ground to
the same ground point used by these ProControl com-
ponents.
NOTE: Different ground points (unequal potential) may
cause current to flow through component cables, caus-
ing incorrect signals.
EasyKey
Connect a ground wire from the EasyKey ground screw
to a true earth ground. F
IG. 14.
Gun Flush Box (Manual or Semi-automatic
mode only)
Connect a ground wire from the Gun Flush Box ground
lug to a true earth ground. F
IG. 14.
Wall Mount Fluid Station
Connect a ground wire from the Wall Mount Fluid Sta-
tion ground screw to a true earth ground. F
IG. 14.
Color Change Module
Connect a ground wire from the Color Change Module
ground screw to a true earth ground. A ground wire and
clamp, part no. 223547, is available from Graco. F
IG. 14.
Flow Meters
Connect the meter cables as shown in the System
Electrical Schematic Hazardous Area on page 31.
Failure to properly connect the shield may cause incor-
rect signals.
Feed Pumps or Pressure Pots
Connect a ground wire and clamp from a true earth
ground to the pumps or pots. See pump or pressure pot
manual.
Air and Fluid Hoses
Use grounded hoses only.
Spray Gun
Follow the grounding instructions in your gun manual.
Fluid Supply Container
Follow local code.
Object Being Sprayed
Follow local code.
All Solvent Pails Used When Purging
Follow local code. Use only conductive metal pails/con-
tainers placed on a grounded surface. Do not place the
pail/container on a nonconductive surface, such as
paper or cardboard, which interrupts the grounding con-
tinuity.
Check Resistance
Have a qualified electrician check resistance between
each ProControl component and true earth ground. If
resistance is greater than 1 ohm, a different ground site
may be required. Do not operate the system until the
problem is corrected.
Your system must be grounded. Read Warnings,
page 6. For intrinsic safety, ground wires for the
EasyKey, Fluid Station, and Gun Flush Box must all be
connected to the same true earth ground. See F
IG. 14,
page 28.
To ensure proper grounding, resistance between Pro-
Mix components and true earth ground must be less
than 1 ohm. Read Warnings, page 6.
Содержание
- A1163a 1
- Installation 1
- Procontro 1
- Contents 2
- Equipment approvals 3
- Related manuals 3
- Models 4
- System configuration and part numbers 4
- Standard features accessories 5
- Warning 6
- Warnings 6
- Warning 7
- Warning 8
- Changing materials 9
- Important two component material information 9
- Isocyanate conditions 9
- Keep components a and b separate 9
- Material self ignition 9
- Moisture sensitivity of isocyanates 9
- Component identification and definition 10
- Intrinsically safe installation requirements 12
- Location 12
- Location requirements 12
- Optional cables 12
- A1163a 13 13
- Advertissement la substitution de composants peut compromettre la securite intrinseque 13
- Class i div i group d t3 us and canada class i zone i group iia t3 atex only taub 20 c to 50 c 13
- Fm08atex0074 system assembly certificate 13
- Intrinsically safe installation 13
- Location 13
- Non hazardous location only hazardous classified location 13
- Note see intrinsically safe installation requirements on page 12 13
- Note this is control drawing also applies to the procontrol 1ks see also 13
- On page 15 13
- Warning substitution of components may impair intrinsic safety for installation maintenance or operation instructions see instruction manual 13
- General information 14
- Wall mounting 14
- A1163a 15 15
- Procontrol 1ks system layout drawing 15
- Wall mounting 15
- Air connections 17
- Air supply 17
- Requirements 17
- Fluid connections 18
- Fluid supply 18
- Requirements 18
- Connect main power 21
- Electrical 21
- Requirements 21
- Connect easykey to fluid station control 22
- 3a1163a 24
- Board to the color change board see 24
- Color change board 1 color change board 2 24
- Connect a 5 pin electrical cable from the labeled con 24
- Connect color change module 24
- Depending on the number of color change boards and color change modules being used in your system 24
- Effect on system 24
- Electrical 24
- For wiring between the color change board and the sole noids see the color change module electrical sche matic 24
- If you are using two color change modules to add colors connect a 5 pin electrical cable from the first color change board to the second color change board 24
- Nection port j11 on the fluid station control 24
- One color change board 24
- S3 s6 s5 s4 s3 s6 s5 s4 24
- Set switches s3 s6 on the color change board s as shown in table 2 and 24
- Table 2 color change board switch settings 24
- To install the color change module s see manual 312787 24
- Two color change boards 24
- 3a1163a 26
- Color change module electrical schematic 26
- Electrical 26
- Wiring diagram 26
- Air and fluid hoses 27
- All solvent pails used when purging 27
- Check resistance 27
- Color change module 27
- Easykey 27
- Feed pumps or pressure pots 27
- Flow meters 27
- Fluid supply container 27
- Grounding 27
- Gun flush box manual or semi automatic mode only 27
- Object being sprayed 27
- Spray gun 27
- Wall mount fluid station 27
- 3a1163a 28
- Control box 28
- Control box ground screw 28
- Control box ground wire 28
- Easykey display 28
- Easykey ground screw 28
- Easykey ground wire 28
- Electrical 28
- Grounding 28
- Robot ground wire connect to separate ground point see note on page 27 28
- Ti16331a 28
- True earth ground check your local code for requirements 28
- A1163a 29 29
- Control air 29
- Purge air 29
- Schematic diagrams 29
- System pneumatic schematic 29
- 3a1163a 30
- Non hazardous area 30
- Note the electrical schematic illustrates all possible wiring expansions in a procontrol 1ks system some compo nents shown are not included with all systems 30
- Schematic diagrams 30
- System electrical schematic 30
- A1163a 31 31
- Booth control board 31
- Flow control board 31
- Fluid press sens 31
- Ground terminal 31
- Hazardous area 31
- I s meters 31
- Note the electrical schematic illustrates all possible wiring expansions in a procontrol 1ks system some compo nents shown are not included with all systems 31
- Schematic diagrams 31
- System electrical schematic 31
- Tecno v p 31
- Dimensions and mounting hole layouts 32
- Wall panel mounting bracket only 32
- Technical data 35
- For the latest information about graco products visit www graco com 36
- Graco headquarters minneapolis international offices belgium china japan korea 36
- Graco inc p o box 1441 minneapolis mn 55440 1441 copyright 2010 graco inc is registered to iso 9001 www graco com 36
- Graco information 36
- Graco standard warranty 36
- To place an order contact your graco distributor or call to identify the nearest distributor phone 612 623 6921 or toll free 1 800 328 0211 fax 612 378 3505 36
Похожие устройства
- Graco ProControl 1KS Технические характеристики
- Graco ProDispense Инструкция по эксплуатации
- Graco ProDispense Брошюра
- Graco ProDispense Сертификат
- Graco EcoQuip 2 EQm Инструкция по эксплуатации
- Graco EcoQuip 2 EQm Брошюра
- Graco EcoQuip 2 EQs Инструкция по эксплуатации
- Graco EcoQuip 2 EQs Брошюра
- Graco EcoQuip 2 EQs Elite Инструкция по эксплуатации
- Graco EcoQuip 2 EQs Elite Брошюра
- Graco EcoQuip 2 EQs2 Twinline Инструкция по эксплуатации
- Graco EcoQuip 2 EQs2 Twinline Брошюра
- Graco Manzel GBL 7500 24K466 Инструкция по эксплуатации
- Graco Manzel GBL 7500 24K466 Технические характеристики
- Graco Manzel GBL 7500 24K466 Сертификат
- Graco Manzel GBL 7500 24J391 Инструкция по эксплуатации
- Graco Manzel GBL 7500 24J391 Технические характеристики
- Graco Manzel GBL 7500 24J392 Инструкция по эксплуатации
- Graco Manzel GBL 7500 24J392 Технические характеристики
- Graco Manzel GBL 7500 24J393 Инструкция по эксплуатации