Makita 6319 DWFE [9/36] Adjustable depth rod fig 4
9
NOTE:
• The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufac-
turer’s batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it
may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-
tery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location
exposed to direct sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a while.
Charging will begin after the battery cartridge is cooled by the cooling fan installed in the charger (DC24SA only).
When the temperature on battery is more than approx. 70°C, two charging lights may flash in red color, and when
approx. 50°C – 70°C, one charging light in red color.
• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger
or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.
• Any of the following conditions indicates damage to the charger and/or battery cartridge. Ask your Makita Authorized
or Factory Service Center to check them.
1) The charging light does not flash (green) when the battery charger is plugged into a power source.
2) The charging light does not light up or flash (red) when the battery is inserted in the charger port.
3) Charging is not completed at even more than two hours after red light comes ON at start of charging.
Side grip (auxiliary handle) (Fig. 3)
Always use the side grip to ensure operating safety.
Install the side grip so that the teeth on the grip fit in
between the protrusions on the tool barrel. Then tighten
the grip by turning clockwise at the desired position. It
may be swung 360° so as to be secured at any position.
Adjustable depth rod (Fig. 4)
The adjustable depth rod is used to drill holes of uniform
depth. Loosen the thumb screw, set to desired position,
then tighten the thumb screw.
Installing or removing driver bit or drill bit
(Fig. 5 & 6)
Important:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before installing or removing
the bit.
Turn the sleeve counterclockwise to open the chuck jaws.
Place the bit in the chuck as far as it will go. Turn the
sleeve clockwise to tighten the chuck. To remove the bit,
turn the sleeve counterclockwise.
When not using the driver bit, keep it in the bit holders.
Bits up to 45 mm long can be kept there.
Switch action (Fig. 7)
CAUTION:
Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the “OFF” position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Reversing switch action (Fig. 8)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for forward rotation or from the B side for reverse
rotation. When the switch lever is in between (the neutral
position), the switch trigger cannot be pulled.
Speed change (Fig. 9)
To change the speed, first switch off the tool and then
slide the speed change lever to the “II” side for high
speed or “I” side for low speed. Be sure that the speed
change lever is set to the correct position before opera-
tion. Use the right speed for your job.
CAUTION:
• Always set the speed change lever fully to the correct
position. If you operate the tool with the speed change
lever positioned half-way between the “I” side and “II”
side, the tool may be damaged.
• Do not use the speed change lever while the tool is run-
ning. The tool may be damaged.
Selecting the action mode (Fig. 10)
This tool employs an action mode changing ring. Select
one of the three modes suitable for your work needs by
using this ring. For rotation only, turn the ring so that the
arrow on the tool body points toward the
M
mark on the
ring. For rotation with hammering, turn the ring so that
the arrow points toward the
X on the ring. For screw-
driving (rotation with clutch), turn the ring so that the
arrow points toward the
U mark on the ring.
CAUTION:
Always set the ring correctly to your desired mode mark.
If you operate the tool with the ring positioned half-way
between the mode marks, the tool may be damaged.
Adjusting the fastening torque (Fig. 11)
The fastening torque can be adjusted in 16 steps by turn-
ing the adjusting ring so that its graduations are aligned
with the arrow on the tool body. The fastening torque is
minimum when the number 1 is aligned with the arrow,
and maximum when the number 16 is aligned with the
arrow.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
Screwdriving operation (Fig. 12)
First, turn the action mode changing ring so that the
arrow on the tool body points to the
U marking. Adjust
the adjusting ring to the proper torque level for your work.
Then proceed as follows.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the trigger as
soon as the clutch cuts in.
Содержание
- Bhp460 1
- Indoor use only 4
- Symbole 4
- Symbols 4
- Символы 4
- Achtung 5
- Do not discard batteries into garbage can or the like 5
- Примечание 5
- English 6
- Explanation of general view 6
- Safety instructions 6
- Specifications 6
- Additional safety rules for charger battery cartridge 7
- Additional safety rules for tool 7
- Important safety instructions for charger battery cartridge 7
- Save these instructions 7
- Charging fig 2 8
- Conditioning charge dc24sa only 8
- Cooling system dc24sa only 8
- Installing or removing battery cartridge fig 1 8
- Operating instructions 8
- Tips for maintaining maximum battery life 8
- Trickle charge maintenance charge 8
- Adjustable depth rod fig 4 9
- Adjusting the fastening torque fig 11 9
- Installing or removing driver bit or drill bit fig 5 6 9
- Reversing switch action fig 8 9
- Screwdriving operation fig 12 9
- Selecting the action mode fig 10 9
- Side grip auxiliary handle fig 3 9
- Speed change fig 9 9
- Switch action fig 7 9
- Blow out bulb fig 13 10
- Drilling operation 10
- Hammer drilling operation 10
- Maintenance 10
- Replacement of carbon brushes fig 14 15 10
- Ec declaration of conformity 11
- Makita international europe ltd 11
- Noise and vibration 11
- Deutsch 12
- Sicherheitsvorschriften 12
- Technische daten 12
- Übersicht 12
- Wichtige sicherheitshinweise für ladegerät und akku 13
- Bedienungshinweise 14
- Bewahren sie diese hinweise sorgfältig auf 14
- Ein und ausbau des akkus abb 1 14
- Umweltschutz 14
- Zusätzliche sicherheitsregeln für die maschine 14
- Zusätzliche sicherheitsregeln für ladegerät und akku 14
- Anpassungsladung 15
- Erhaltungsladung 15
- Kühlsystem 15
- Laden abb 2 15
- Tips zur erhaltung der maximalen akkulebensdauer 15
- Drehrichtungsumschalter abb 8 16
- Drehzahlumschalter abb 9 16
- Montage und demontage des schraubendreher bzw bohrereinsatzes abb 5 u 6 16
- Schalterfunktion abb 7 16
- Seitengriff zusatzgriff abb 3 16
- Verstellbarer tiefenanschlag abb 4 16
- Wahl der betriebsart abb 10 16
- Bohren 17
- Einstellen des anziehdrehmoments abb 11 17
- Schlagbohrbetrieb 17
- Schraubbetrieb abb 12 17
- Blaseball abb 13 18
- Ce 2003 18
- Ce konformitätserklärung 18
- Geräusch und vibrationsentwicklung 18
- Kohlebürsten wechseln abb 14 u 15 18
- Makita international europe ltd 18
- Wartung 18
- Dane techniczne 19
- Instrukcje bezpieczeństwa 19
- Ostrzeżenie używając urządzeń zasilanych akumulatorem podstawowe środki ostrożności muszą być zachowane aby zmniejszyć ryzyko ognia wycieku elektrolitu i uszkodzenia ciała włączając poniższe przeczytaj wszystkie podane instrukcje przed użyciem tego produktu i zachowaj je do wglądu dla bezpiecznego użycia 19
- Polski 19
- Wyjaśnienia dotyczące narzędzia i jego użycia 19
- Ważne zalecenia dotyczące bezpiecznego posługiwania się ładowarką i wkładką akumulatorową 20
- Dodatkowe zaelcenia dotyczące bezpiecznego posługiwania się ładowarką i wkładką akumulatorową 21
- Dodatkowe zasady bezpieczeństwa 21
- Instrukcja obsługi 21
- Nie przechowuj urządzenia ani wkładki akumulatorowej w miejscach gdzie temperatura może dochodzić do lub przekraczać 50 c 122 f 21
- Przestrzegać niniejszych instrukcji 21
- Wkładanie lub wyjmowanie wkładki akumulatorowej rys 21
- Ładowanie rys 21
- Dc24sa 22
- Podładowywanie ładowanie ciągłe małym prądem 22
- Porady dotyczące zapewnienia maksymalnej żywotności akumulatora 22
- Układ chłodzenia 22
- Ładowanie optymalne 22
- Działanie przełącznika rys 7 23
- Działanie przełącznika zmiany kierunku rys 8 23
- Operacje wkręcania rys 2 23
- Regulacja momentu dokręcającego rys 11 23
- Regulowalny miernik głębokości rys 4 23
- Uchwyt boczny pomocniczy rys 3 23
- Wybór trybu pracy rys 10 23
- Zakładanie lub wyjmowanie końcówki śrubokrętowej lub wiertła rys 5 i 6 23
- Zmiana prędkości rys 9 23
- Gruszka do wydmuchiwania pyłów rys 13 24
- Konserwacja uwaga 24
- Operacje wiercenia 24
- Wiercenie udarowe 24
- Wymiana szczoteczek węglowych rys 14 i 15 24
- Ce 2003 25
- Makita international europe ltd 25
- Szummy i drgania 25
- Ue deklaracja zgodności 25
- Инструкции по мерам безопасности 26
- Русский язык 26
- Технические характеристики 26
- Важные инструкции по безопасности для зарядного устройства и батареиного картриджа 27
- Дополнительные правила безопасности 28
- Дополнительные правила безопасности для зарядного устройства и батарейного картриджа 28
- Инструкция по эксплуатации 28
- Сохраните эти инструкции 28
- Компенсационная зарядка эксплуатационная зарядка 29
- Советы по поддержанию максимального срока службы батареи 29
- Боковой захват дополнительная ручка рис 3 30
- Действие обратного переключения рис 8 30
- Действия при переключении рис 7 30
- Регулируемый стержень глубины рис 4 30
- Установка или удаление завинчивающего сверла или сверла дрели рис 5 и 6 30
- Выбор действующего режима рис 10 31
- Операция завинчивания рис 2 31
- Операция сверления 31
- Переключение скорости рис 9 31
- Регулировка крутящего момента рис 11 31
- Воздуходувный баллон рис 13 32
- Замена угольных щеток рис 12 и 13 32
- Обслуживание 32
- Операция сверления с отбоем 32
- Ce 2003 33
- Makita international europe ltd 33
- Ес декларация соответствия 33
- Шум и вибрация 33
Похожие устройства
- Scarlett SC-1177 Инструкция по эксплуатации
- Gorenje K12E Инструкция по эксплуатации
- M-Audio Oxygen 61 Инструкция по эксплуатации
- Nokia 7230 Graphite Инструкция по эксплуатации
- Makita 6980 FDWDE Инструкция по эксплуатации
- Scarlett SC-1176 Инструкция по эксплуатации
- Gorenje K17W Инструкция по эксплуатации
- M-Audio Oxygen 49 Инструкция по эксплуатации
- Nokia 2720 Deep Red Инструкция по эксплуатации
- Makita BTW 200 SAE Инструкция по эксплуатации
- Proma BPK-2075/400 25702154 Инструкция по эксплуатации
- Scarlett SC-1175 Инструкция по эксплуатации
- HP N121XL (CC641HE) Инструкция по эксплуатации
- Gorenje K17E Инструкция по эксплуатации
- Nokia X3-02 White Silver Инструкция по эксплуатации
- Makita 6805 BV Инструкция по эксплуатации
- Proma BO-25 25000370 Инструкция по эксплуатации
- Scarlett SC-1174 Инструкция по эксплуатации
- Gorenje FS900W Инструкция по эксплуатации
- AEG MCD2541E-M Инструкция по эксплуатации