Home
Главная
Bosch
Парогенератор
TDS 2515
Инструкция по эксплуатации Страница: 14

Bosch TDS 2515 [14/122] Cleaning maintenance

Bosch TDS 2510 [14/122] Cleaning maintenance

Trouble shooting

Problem Possible causes Solution

The steam generator

does not come on.

• There is a connection problem.

• The steam tank and/or main power

button is not switched on.

• Check the mains cable, the plug and

the socket.

• Press the buttons for main power (6)

and steam tank (4) «On/Start».

The iron does not

heat up.

• The main power button is not

switched on.

• The temperature control knob is set

to the «min» position.

• Press the main power button (6) «On».

• Set the temperature control knob (13)

to the desired position.

The iron begins

to smoke when

switched on.

• During first use: Certain components

on the appliance have been lightly

greased at the factory and may

produce a little smoke when initially

heated.

• During later use: the soleplate may

be soiled.

• This is completely normal and will stop

after a short while.

• Clean the soleplate according to the

cleaning instructions in this manual.

Water flows through

the holes on the sole

plate.

• The steam function is being used

before it has reached temperature.

• The water is condensing inside the

pipes because steam is being used

for the first time or has not been

used for a long time.

• Reduce the steam flow when ironing

at low temperatures (Variable steam

control (3)).

• Point the iron away from the ironing

area and press the steam release

button (15) until steam is produced.

5. Shake the base unit for a few moments and then

empty it completely over a sink or bucket. To

obtain the best result, we recommend that this

operation is done twice

6. Important: before re-closing, make sure no water

remains in the boiler.

7. Replace and tighten up the boiler drainage plug

with a coin

Intelligent steam

This ironing system has intelligent steam control,

which provides additional steam depending on the

user demand.

Cleaning & Maintenance

1. After ironing, pull out the plug and allow the

appliance to cool down before cleaning.

2. Wipe the housing, handle and iron body with a

damp cloth.

3. If the soleplate is soiled with dirt or scale, clean

it with a damp cloth.

4. Never use abrasive products or solvents.

Important:

• Always unplug the appliance from the mains

supply before carrying out any cleaning or

maintenance operation on it.

Storing the appliance (D)

1. Always allow the appliance to cool down before

storing it.

2. Set the switches for main power and steam

boiler to the «Off/Stop» position and disconnect

the connection.

3. Place the iron on the iron pad, standing on the

soleplate.

4. Empty the water tank and store the mains cable

on the cord rewind facility. Tidy the steam hose

on the handle of the iron using the cord clip

provided (12). Do not wrap the cords too tight.

Содержание

Похожие устройства

en 5 Shake the base unit for a few moments and then empty it completely over a silk or bucket To obtain the best result we recommend that this operation is done twice 6 Important before re closng make sure no water remans h the boiler 7 Replace and tighten up the boiler cfrahage plug with a con Intelligent steam This ronng system has ntelligent steam control which provides additional steam depending on the user demand Cleaning Maintenance 1 After ronng pull out the plug and allow the appliance to cool down before clean ng 2 Wipe the housng handle and ron body with a damp cloth 3 If the soleplate is soiled with dirt or scale clean it with a damp cloth 4 Never use abrasive products or solvents Important Always unplug the appliance from the mans supply before carryng out any cleanng or mantenance operation on it Storing the appliance D 1 Always allow the appliance to cool down before storng it 2 Set the switches for man power and steam boiler to the Off Stop position and disconnect the connection 3 Place the iron on the ron pad standng on the soleplate 4 Empty the water tank and store the mans cable on the cord rewind facility Tidy the steam hose on the handle of the iron usng the cord clip provided 12 Do not wrap the cords too tight Trouble shooting Problem Possible causes Solution The steam generator doesnot come on There is a connection problem Check the mans cable the plug and the socket Press the buttons for main power 6 and steam tank 4 On Start The steam tank and or man power button is not switched on The iron does not heat up The man power button is not switched on The temperature control knob is set to the mh position Press the man power button 6 On Set the temperature control knob 13 to the desired position The iron begns to smoke when switched on During first use Certain components on the appliance have been lightly greased at the factory and may produce a little smoke when n itially heated During later use the soleplate may be soiled This is completely normal and will stop after a short while The steam junction is being used before it has reached temperature Reduce the steam flow when ronng at low temperatures Variable steam control 3 Pont the iron away from the ronng area and press the steam release button 15 until steam is produced Water flows through the holes on the sole plate The water is condensing inside the pipes because steam is being used for the first trne or has not been used for a long time 14 Clean the soleplate accordng to the cleaning nstructions n this manual

Скачать