![Hitachi CM 9 SR [11/78] English](/img/pdf.png)
Hitachi CM 9 SR [11/78] English
![Hitachi CM9SR [11/78] English](/views2/1002845/page11/bgb.png)
10
English
Loosening the wing nut and moving the base will
allow adjustment of the cutting depth.
CAUTIONS
䡬 Leaving the wing nut loosened may result in injury.
Securely tighten the wing nut after adjusting the
cutting depth.
INSTALLING DUST COLLECTION HOSE
When cutting a material which generates cutting dust,
use the dust collection hose as follows:
(1) Remove the rubber cap and install the accessory
adaptor. (Fig. 4)
(2) Install the dust collector hose for the power tool in
the accessory adaptor. (Fig. 4)
CAUTION
䡬 Always install a rubber cap on the dust collection
adaptor when the dust collection hose is not used.
INSTALLING/REMOVING DIAMOND WHEEL
1. Installation
(1) Loosen the knob nut and remove the cover (B).
(2) Wipe the cutting dust from the spindle and washers.
(3) Make sure the rotation direction of the diamond
wheel conforms to the direction indicated on the
gear case and install the diamond wheel as shown
in Fig. 1.
(4) Press the lock pin and secure the spindle. Tighten
the wheel nut adequately with the provided wrench.
(Fig. 1)
NOTE
䡬 Always use the provided wrench to secure the wheel
nut.
2. Removal
Remove the wheel nut with the provided wrench
and remove the diamond wheel. (Fig. 1)
CUTTING
1. Cutting procedures (Fig. 5)
(1) Place this tool on the material to be cut and align
the cutting line and the diamond wheel.
The cutting can be performed smoothly if you cut
straight ahead on the cutting line in the initial cut.
(2) Turn on the switch when the diamond wheel is not
touching the material to be cut.
2. Switch operation
Switch ON: Push the locking button forward and
then press the switch lever.
* For continuous use, press the switch
lever. The switch lever is locked by
pushing the locking button forward
once again.
(*Subject to change depending on
area.)
Switch OFF: Press and release the switch lever.
3. Precautions immediately after finishing operation
After switching off the machine, do not put it down
until the depressed center wheel has come to a
complete stop. Apart from avoiding serious accidents,
this precaution will reduce the amount of dust and
swarf sucked into the machine.
STANDARD ACCESSORIES
(1) Wrench ........................................................................ 1
(2) Adaptor ....................................................................... 1
Standard accessories are subject to change without notice.
APPLICATION
䡬 Cutting or scribing concrete
䡬 Cutting or scribing tile
䡬 Cutting or scribing stone
䡬 Cutting or scribing roof tile
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a power receptacle while
the power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Checking and installing the diamond wheel
Check the diamond wheel is a specified one and
is not cracked, broken or bent. Check the diamond
wheel is installed securely. For installation, refer to
“Installing/removing diamond wheel”.
5. Fitting and adjusting the dust collection cover (Fig. 1,
Fig. 2)
The dust collection cover is a protective device to
prevent injury should the diamond wheel shatter
during operation. Ensure that the cover is properly
fitted and fastened before commencing cutting
operation.
[Installing and adjusting the dust collection cover]
䡬 Open the lever and insert the locating pin of dust
collection cover, bringing it into line with the across
flats of packing ground.
䡬 Then, turn the dust collection cover to a desired
position (for use).
䡬 Close the lever and fix it. If and when required, carry
out adjustments by tightening or loosening the screw.
䡬 If the lever does not move smoothly, apply some
lubricating oil to the sliding section between the set
piece and the lever.
䡬 Fasten the dust collection cover at the position where
the across flats of the dust collection cover
positioning pin and packing ground are aligned (the
position where the dust collection cover is inserted),
but do not use it.
6. Confirm the spindle lock mechanism
Confirm that the spindle lock is disengaged by
pushing push button two or three times before
switching the power tool on (See Fig. 1).
7. Cutting depth adjustment (Fig. 3)
Lowering the wing nut will loosen and raising it will
tighten.
01Eng_CM9SR_EE 6/30/08, 17:2510
Содержание
- Cm 9sr 1
- Cm 9uby 1
- Cutter steinsäge èûîô ú ôóô ì úì úô przecinarka tarczowa daraboló řezačka beton kesme masina de taiat caneluri in zidarie rezalnik aîïaáìaó ôëîa 1
- Hitachi koki co ltd 1
- ㅃ潶敲䙟䍍㥓剟䕅 1
- Cm 9sr 2
- Cm 9uby 2
- Cutter steinsäge èûîô ú ôóô ì úì úô przecinarka tarczowa daraboló řezačka beton kesme masina de taiat caneluri in zidarie rezalnik aîïaáìaó ôëîa 2
- Hitachi koki co ltd 2
- ㅃ潶敲䙟䍍㥓剟䕅 2
- Hitachi power tools czech s r o 3
- Hitachi power tools hungary kft 3
- Hitachi power tools netherlands b v moscow branch 3
- Hitachi power tools polska sp z o o 3
- Hitachi power tools romania 3
- Hitachi power tools österreich gmbh 3
- Q r t s 3
- 潶敲䉟䍍㥓剟䕅 3
- Hitachi power tools czech s r o 4
- Hitachi power tools hungary kft 4
- Hitachi power tools netherlands b v moscow branch 4
- Hitachi power tools polska sp z o o 4
- Hitachi power tools romania 4
- Hitachi power tools österreich gmbh 4
- Q r t s 4
- 潶敲䉟䍍㥓剟䕅 4
- 呡扬敟䍍㥓剟䕅 5
- Always wear eye protection tragen sie immer einen augenschutz 7
- Always wear hearing protection stets gehörschutz tragen 7
- Avertisment 7
- Bceöàa ìaàeçaèúe cpeàcúça áaçëúê opöaìoç cîyxa 7
- Bceöàa ìaàeçaèúe cpeàcúça áaçëúê öîaá 7
- Cëïçoîê 7
- Daima koruyucu gözlük takın 7
- Dókkat 7
- Figyelem 7
- Jelölések 7
- Mindig viseljen védőszemüveget 7
- Olvasson el minden biztonsági figyelmeztetést és minden utasítást a figyelmeztetések és utasítások be nem tartása áramütést tüzet és vagy súlyos sérülést eredményezhet 7
- Opozorilo 7
- Ostrzeżenie 7
- Purtaţi întotdeauna protecţie auditivă obvezna je uporaba zaščite za ušesa 7
- Purtaţi întotdeauna protecţie pentru ochi 7
- Simboli 7
- Simboluri 7
- Simgeler 7
- Symbole 7
- Symbols 7
- Symboly 7
- Uporaba zaščite za oči je obvezna 7
- Upozornění 7
- V nadaljevanju so prikazani simboli uporabljeni pri stroju pred uporabo se prepričajte da jih razumete 7
- Vždy noste ochranu očí 7
- Vždy používejte chrániče sluchu daima koruyucu kulaklık takın 7
- Warning 7
- Warnung 7
- Zawsze nosić okulary ochronne 7
- Zawsze nosić słuchawki ochronne 7
- Ì ôï 7
- Φ ράτε πάντα τ ν κατάλληλ ε πλισµ για την πρ στασία των µατιών 7
- English 8
- General power tool safety warnings 8
- 〱䕮束䍍㥓剟䕅 8
- Cutter safety warnings 9
- English 9
- Kickback and related warnings 9
- English 10
- Precaution on using cutter 10
- Specifications 10
- Application 11
- Cutting 11
- English 11
- Installing dust collection hose 11
- Installing removing diamond wheel 11
- Prior to operation 11
- Standard accessories 11
- English 12
- Maintenance and inspection 12
- English 13
- Guarantee 13
- Allgemeine sicherheitshinweise für elektrogeräte 14
- Deutsch 14
- 〲䝥牟䍍㥓剟䕅 14
- Deutsch 15
- Sicherheitswarnungen für die benutzung der steinsäge 15
- Deutsch 16
- Rückstoss und damit verbundene warnungen 16
- Anwendungsgebiete 17
- Deutsch 17
- Standardzubehör 17
- Technische daten 17
- Vor der inbetriebnahme 17
- Vorsichtsmassnahmen bei verwendung der steinsäge 17
- Deutsch 18
- Installation ausbauen der diamantschleifscheibe 18
- Installation des staubabscheide schlauchs 18
- Schneiden 18
- Deutsch 19
- Garantie 19
- Wartung und inspektion 19
- Deutsch 20
- Ïïëóèî 21
- Π ƒ π π π º π ƒπ à ƒ π à 21
- 〳䝲敟䍍㥓剟䕅 21
- Ïïëóèî 22
- Ƒ π π π º π π ƒπ à ª ƒª ƒ à 22
- ª π ã π ƒ π π π 23
- Ïïëóèî 23
- º ƒª 24
- Ã π ã ƒ ƒπ π 24
- Ïïëóèî 24
- Ƒ ã ムà π ƒπ à ª ƒª ƒ à 24
- Ƒπ π àƒ π 24
- Π ƒ ª 24
- À ƒª à ƒª π ª π à ƒ ã à 25
- À ƒª ø à 25
- Ïïëóèî 25
- À ƒ π ã 26
- Ïïëóèî 26
- Ïïëóèî 27
- Ogólne wskazówki bezpieczeństwa dotyczące urządzeń elektrycznych 28
- Polski 28
- 〴偯江䍍㥓剟䕅 28
- Polski 29
- Wskazówki bezpieczeństwa dotyczące przecinarki tarczowej 29
- Odrzut i związane z nim ostrzeżenia 30
- Polski 30
- Dane techniczne 31
- Polski 31
- Przed użyciem 31
- Wskazówki bezpieczeństwa dotyczące użytkowania urządzenia 31
- Wyposażenie standardowe 31
- Zastosowanie 31
- Cięcie 32
- Konserwacja i inspekcja 32
- Polski 32
- Zakładanie węża systemu odprowadzania pyłu 32
- Zakładanie zdejmowanie diamentowej tarczy tnącej 32
- Gwarancja 33
- Polski 33
- Polski 34
- Magyar 35
- Szerszámgépekre vonatkozó általános biztonsági figyelmeztetések 35
- 〵䡵湟䍍㥓剟䕅 35
- A daraboló biztonsági figyelmeztetése 36
- Magyar 36
- Magyar 37
- Visszarúgás és kapcsolódó figyelmeztetések 37
- Óvintézkedések a daraboló használatával kapcsolatban 37
- Alkalmazások 38
- Az üzembehelyezés előtti tennivalók 38
- Gyémántkorong felszerelése eltávolítása 38
- Magyar 38
- Műszaki adatok 38
- Porgyűjtő tömlő felszerelése 38
- Ellenőrzés és karbantartás 39
- Magyar 39
- Vágás 39
- Garancia 40
- Magyar 40
- Obecná varování týkající se bezpečnosti el přístroje 41
- Čeština 41
- 䍺敟䍍㥓剟䕅 41
- Bezpečnostní upozornění týkající se řezačky 42
- Čeština 42
- Odmrštění a příslušná varování 43
- Upozornění pro používání řezačky 43
- Čeština 43
- Instalace demontáž diamantového kotouče 44
- Instalace hadice pro zachycování prachu 44
- Parametry 44
- Použití 44
- Před použitím 44
- Standardní příslušenství 44
- Čeština 44
- Údržba a kontrola 45
- Čeština 45
- Řezání 45
- Záruka 46
- Čeština 46
- Genel elektrókló alet güvenlók uyarilari 47
- Türkçe 47
- 呵牟䍍㥓剟䕅 47
- Beton kesme güvenlók uyarilari 48
- Geró tepme ve ólgóló uyarilar 48
- Türkçe 48
- Beton kesócónón kullanilmasiyla ólgóló uyarilar 49
- Teknók özellókler 49
- Türkçe 49
- Aletó kullanmadan önce 50
- Elmas çarkin takilmasi çikarilmasi 50
- Standart aksesuarlar 50
- Toz emme hortumunun takilmasi 50
- Türkçe 50
- Uygulamalar 50
- Bakim ve ónceleme 51
- Garantó 51
- Türkçe 51
- Türkçe 52
- Avertismente generale privind siguranţa în folosirea sculei electrice 53
- Română 53
- 〸副浟䍍㥓剟䕅 53
- Avertizări pentru mașina de tăiat caneluri în zidărie 54
- Română 54
- Precauţii la folosirea mașinii de tăiat caneluri în zidărie 55
- Reculul și avertizările referitoare la recul 55
- Română 55
- Accesorii standard 56
- Română 56
- Specificaţii 56
- Utilizare 56
- Înainte de utilizare 56
- Montarea demontarea discului diamantat 57
- Montarea furtunului pentru colectarea prafului 57
- Română 57
- Tăiere 57
- Întreţinere și verificare 57
- Garanţie 58
- Română 58
- Slovenščina 59
- Splošna varnostna navodila za električno orodje 59
- 〹卬潟䍍㥓剟䕅 59
- Slovenščina 60
- Varnostna opozorila v zvezi z rezalnikom 60
- Slovenščina 61
- Specifikacije 61
- Udarec nazaj in nevarnost s tem v zvezi 61
- Varnostni ukrepi za uporabo rezalnika 61
- Nameščanje cevi za zbiranje prahu 62
- Nameščanje odstranjevanje diamantnega kolesa 62
- Pred uporabo 62
- Rezanje 62
- Slovenščina 62
- Standardni dodatki 62
- Uporaba 62
- Garancija 63
- Slovenščina 63
- Vzdrževanje in pregledi 63
- Slovenščina 64
- Oåôàe èpabàãa åeâoèachoctà èpà paåote c ùãektpoàhctpìmehtom 65
- Pyccíëè 65
- 創獟䍍㥓剟䕅 65
- Pyccíëè 66
- Èpeñoctepeüehàe èo åeâoèachomì èoãúâobahàû aãmaâhoâ èàãoâ 66
- Bõåpoc oåpathoéo haèpüüehàü à cbüâahhõe c ùtàm èpeñìèpeüñehàü 67
- Pyccíëè 67
- Mepõ èpeñoctopoühoctà èpà paåote c aãmaâhoâ èàãoâ 68
- Pyccíëè 68
- Ctahñapthõe akceccìapõ 69
- Oåãactú èpàmehehàü 69
- Pyccíëè 69
- Texhàóeckàe xapaktepàctàkà 69
- Èoñéotobka k ùkcèãìatañàà 69
- Peâka 70
- Pyccíëè 70
- Texhàóeckoe oåcãìüàbahàe à èpobepka 70
- Ìctahobka chütàe òãàîobaãúhoéo kpìéa c aãmaâhoâ kpomkoâ 70
- Ìctahobka òãahéa èõãeìãobàteãü 70
- Pyccíëè 71
- Éapahtàü 71
- Pyccíëè 72
- ㄱ䉡捫彃䴹卒彅 73
- Cm9uby 74
- Hitachi power tools czech s r o 77
- Hitachi power tools hungary kft 77
- Hitachi power tools netherlands b v moscow branch 77
- Hitachi power tools polska sp z o o 77
- Hitachi power tools romania 77
- Hitachi power tools österreich gmbh 77
- Q r t s 77
- 潶敲䉟䍍㥓剟䕅 77
- Cm 9sr 78
- Cm 9uby 78
- Cutter steinsäge èûîô ú ôóô ì úì úô przecinarka tarczowa daraboló řezačka beton kesme masina de taiat caneluri in zidarie rezalnik aîïaáìaó ôëîa 78
- Hitachi koki co ltd 78
- ㅃ潶敲䙟䍍㥓剟䕅 78
Похожие устройства
- Panasonic SC-PT70EE-K Инструкция по эксплуатации
- Behringer ULTRA CHORUS UC100 Инструкция по эксплуатации
- Panasonic SC-BFT800EE-K Инструкция по эксплуатации
- Hitachi CM 5 SB Инструкция по эксплуатации
- Behringer ULTRA DISTORTION UD100 Инструкция по эксплуатации
- Karcher KMR 1250 D KAT Инструкция по эксплуатации
- Philips HTS7140 Инструкция по эксплуатации
- Sparky FK 653 Инструкция по эксплуатации
- Behringer ULTRA FLANGER UF100 Инструкция по эксплуатации
- Karcher KMR 1250 B 2SB Инструкция по эксплуатации
- Asus WX-LAMBOR White Инструкция по эксплуатации
- AEG 413605 MFE 1500 Инструкция по эксплуатации
- Philips HTS5120 ⁄ 51 Инструкция по эксплуатации
- Behringer ULTRA METAL UM100 Инструкция по эксплуатации
- Karcher KMR 1250 LPG 2SB Инструкция по эксплуатации
- Tomahawk CAN-1000 Инструкция по эксплуатации
- Philips HTS9520 Инструкция по эксплуатации
- Bosch GNF 20 CA 0.601.612.508 Инструкция по эксплуатации
- Tomahawk Х5 Инструкция по эксплуатации
- Karcher KMR 1250 D Инструкция по эксплуатации